Hathaway Logan 7-FT 3-IN-1 Pool Table with Benches Assembly Instructions

Thank You

Thank you for purchasing this product. Hathaway works around the clock and around the globe to ensure that its products maintain the highest possible quality. In the rare case of issues during assembly or use of this product, please contact the Consumer Hotline at 800-759-0977 for immediate assistance before contacting your retailer. Please read the warranty information for further details.

Assembly Tips

1. Find a clean, level surface to begin assembly. Two adults are recommended for assembly. Use the box corners as a work surface if needed.
2. Remove all contents from the box and verify all parts against the Parts List before beginning assembly. Note: Some parts may be pre-installed or pre-assembled.
3. Some figures or drawings may not look exactly like the product.
4. When installing parts with multiple screws or bolts, hand-tighten all fasteners first, then final tighten with a screwdriver or wrench.
5. Electric screwdrivers can be helpful, but set a low torque and use caution to avoid stripping screws or overtightening, which can damage parts.

Care and Use

1. This product is intended for INDOOR use only.
2. Do NOT drag the table when moving it, as this will damage the legs.

Parts List

All items are packaged in Carton A, except for Bench Parts which are packaged in Carton B.

Hardware Pack - NGP7533

Assembly Instructions

Follow these steps to assemble your Hathaway Logan 7-FT 3-IN-1 Pool Table with Benches.

Bench Assembly

Assemble the benches first. Attach the bench legs (#20) to the bench seat (#19). Secure these using the bench end supports (#21) and appropriate hardware (bolts, nuts, washers from the hardware pack). Install the bench cross braces (#22) and bench middle supports (#23) to connect bench legs for stability. Attach the bench plates (#37) to the underside of the bench seat.

Important Warning: Exercise caution when opening and closing the bench lid. Do not allow children to operate the bench lid. When moving the bench, be cautious. The EVA pads (#24) allow the bench to slide on hard flooring but may cause tipping on carpeting. Lift the bench by its ends to move it.

Pool Table Frame Assembly

Begin assembling the main pool table frame. Attach the left leg (#12) and right leg (#13) to the table body (#11). Secure the legs using the leg end supports (#16) and leg middle panels (#17), along with the leg middle braces (#18). Use the provided hardware (bolts, nuts, washers) for these connections. Install the leg levelers (#32) at the bottom of each leg to ensure the table is stable and level.

Table Top and Game Setup

Once the main frame is assembled, carefully place table top A (#14) and table top B (#15) onto the frame. Ensure they are properly aligned. For table tennis play, attach the table tennis net and posts (#35) to the designated points on the table surface.

General Assembly Guidance

Always verify all parts are present before starting. Hand-tighten all screws and bolts initially, then proceed to final tightening. It is recommended that two adults work together for the assembly process due to the weight of the components.

180-Day Limited Warranty

This product is warranted to the original purchaser to be free from defects in material or workmanship for a period of 180 days from the date of the original retail purchase. This warranty does not cover defects or damage due to improper installation, alteration, accident, or any other event beyond the control of the manufacturer. Defects or damage resulting from misuse, abuse, or negligence will void this warranty. This warranty does not cover scratching or damage that may result from normal usage.

This product is not intended for institutional or commercial use; the manufacturer does not assume any liability for such use. Institutional or commercial use will void this warranty.

This warranty is nontransferable and is expressly limited to the repair or replacement of the defective product. During the warranty period, the manufacturer shall repair or replace defective parts at no cost to the purchaser. Shipping charges and insurance are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation, or replacement of the product or components are not covered under this warranty.

The manufacturer reserves the right to make substitutions to warranty claims if parts are unavailable or obsolete.

The manufacturer shall not be liable for loss of use of the product or other consequential or incidental costs, expenses, or damages incurred by the consumer of any other use. The user assumes all risk of injury resulting from the use of this product.

This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability or fitness for use to the extent permitted by Federal or state law. Neither the manufacturer nor any of its representatives assumes any other liability in connection with this product.

All warranty claims must be made through the retailer where the product was originally purchased. A purchase receipt or other proof of date of purchase will be required to process all warranty claims. The model number and part numbers found within the assembly instructions will be required when submitting any parts requests or warranty claims.

For further warranty information or inquiries, please call 800-759-0977.