Custom P-Ranger Rugged Handheld Device

Technical Specifications

Warnings and Safety Information

Please read the following warnings and safety guidelines carefully to ensure safe and proper use of the device.

Battery Warnings

1. The rechargeable battery powers the device. Charge the battery when the power level is low. It is recommended to use the entire battery charge before recharging to ensure longer battery life.
2. Do not connect the charger to any power source if it is not in good condition.
3. Never connect the charger to the battery for more than one week, as overcharging shortens battery life.
4. Temperature affects battery charge limits; cool or warm the battery before charging. Recharging may not be successful if the battery temperature is above 55°C or below -20°C.
5. To avoid short circuits, use the battery only for its intended purpose. A short circuit occurs if the battery cathode and anode are connected by a conductor.
6. Never use a damaged battery.
7. Battery life is reduced in extremely hot or cold environments. The device may not function properly under such conditions, even if the battery is fully charged.
8. Do not throw the battery into fire. Dispose of used batteries responsibly via battery recycling services according to local regulations.

Device Warnings

1. Keep the device and accessories out of reach of children.
2. Keep the device dry, as liquids can corrode metal circuits. Avoid high temperatures, which can reduce the life of electronic components, melt plastics, and damage the battery.
3. Do not attempt to open the device case or disassemble the phone. Non-professional disassembly may cause damage.
4. Do not use detergents containing strong acids or strong alkaline to clean the phone.
5. Always use original accessories; otherwise, the warranty will be void.

General Safety Information

1. When using the device, always comply with safety rules to protect users and the environment.

Safety in Traffic

1. Except in emergencies, do not use the device while driving unless hands-free devices are connected to ensure safety and freedom of movement.
2. Ensure complete focus on driving. Park the vehicle in a safe place before using the device. Comply with all applicable regulations. Some electronic devices may be affected by radio waves from this device if not sufficiently protected.
3. It is recommended to use the device only in vehicles with an external antenna.
4. Always employ qualified technicians to install the device in a vehicle.

Flight Safety

1. Switch off the device before boarding aircraft. Devices can interfere with aircraft operations and the mobile network. Using devices on aircraft is illegal and may result in denial of customer service.

Environmental Safety

1. Always comply with current applicable rules and policies.
2. Switch off the device when its use is prohibited or may cause interference or hazards.
3. Wireless transmission equipment, including this device, may interfere with inadequately protected medical devices. Consult a physician or medical device manufacturer if you have questions. The device may interfere with hearing aids, pacemakers, and other electronic medical devices. Follow recommendations from doctors or manufacturers.
4. Users are recommended to switch off devices in places where an explosion may occur (e.g., gas stations, chemical plants). Comply with any restrictions on wireless device use.

FCC Regulatory Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 1.6W/Kg averaged over one gram of this Device RP310 (FCC ID: OAH-5221120). SAR information can be viewed online at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search. This device was tested for typical operations 10mm from the body. To maintain compliance with FCC RF exposure requirements, a 10mm separation distance should be maintained from the user's body.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC ID: OAH-5221120

Disposal Guidelines

Within the European Union

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark [recycle symbol] must be disposed of separately from normal household waste.

Outside the European Union

This includes monitors and electrical accessories, such as signal cables or power cords. When disposing of your display products, please follow the guidance of your local authority, ask the shop where you purchased the product, or follow any applicable agreements. The mark on electrical and electronic products applies only to current European Union Member States.

Short Guide

Box Contents

• 1. Documentation (User manual)
• 2. Device
• 3. Hand strap

Device Components

The device features the following components:

• 1. Headphone jack
• 2. Barcode Scanner
• 3. Touchscreen display
• 4. Barcode trigger key
• 5. +/- Volume keys
• 6. Back Button (OS)
• 7. Home button (OS)
• 8. Menu button (OS)
• 9. F1 Function key
• 10. F2 Function key
• 11. Home button
• 12. Recharge with cradle port
• 13. Battery (internal)
• 14. SIM cards + MicroSD card slot
• 15. Speaker
• 16. Camera
• 17. Barcode trigger key (secondary)
• 18. USB Type-C port

This document provides a description of the main features of the device. For a detailed description of all functions, please refer to the user manual by downloading it from the website www.custom4u.it.

Charging the Battery

Be sure to charge the battery to full when charging it for the first time.

Charging with USB Cable

To charge the battery:

1. Locate the USB Type-C port on the P-Ranger and connect a USB cable (optional).
2. Connect the USB cable to a PC or a suitable power adapter.

Charging with Cradle

To charge the battery:

1. Connect the charging cradle (optional) to a power outlet.
2. Place the device on the charging cradle.

Installing MicroSD and/or SIM Cards

To install SIM cards and/or a MicroSD card:

1. Unscrew the two fixing screws on the back of the device.
2. Remove the plastic cover.
3. Insert the SIM cards and MicroSD card into their respective slots.
4. Reassemble the cover and fix it with the two screws previously removed.

Installing / Replacing the Battery

To install or replace the battery:

1. Unscrew the two fixing screws on the back of the device.
2. Remove the plastic cover.
3. Remove the old battery (if applicable).
4. Place the replacement battery in its slot.
5. Assemble the cover as shown in the figure and fix it with the two screws previously removed.

Product Information

Product Code: 0578200M000026 Rev. 1.14

Markets: US & MEA

Model: P-RANGER 5" RUGGED HANDHELD RP100

FCC ID: OAH-5221120

Manufactured by CUSTOM S.p.A. World Headquarters Via Berettine, 2/B - 43010 Fontevivo, Parma ITALY. Tel. +39 0521 680111 - Fax +39 0521 610701. info@custom.biz - www.custom.biz. All rights reserved.