Smart Plug Mini 2 - Type G

Product Description

The Smart Plug Mini 2 is an intelligent, remotely controlled adapter. It monitors power consumption and allows users to instantly turn on and off any connected device from anywhere in the world or from their couch.

Precautions

• Do not remove the product label as it contains important information.
• Avoid switching maximum loads frequently on or off to sustain a long life for the smart plug.
• Be careful that no liquid gets into the smart plug, as it may damage the equipment.

Getting Started

1. Connect the Smart Plug Mini 2 to the power outlet.
2. The Smart Plug Mini 2 will begin searching (up to 15 minutes) for a Zigbee network to join.
3. Ensure your Zigbee network is open for joining devices and will accept the Smart Plug Mini 2.
4. While searching, the LED button on the Smart Plug Mini 2 will flash yellow.
5. When the LED button stops flashing, the Smart Plug Mini 2 has successfully joined the Zigbee network.

Note: Pressing the button on the Smart Plug Mini 2 turns it on. The LED light may appear orange/yellow during network search as it flashes yellow and green simultaneously.

Placement

• Place the smart plug indoors within a temperature range of 0-50°C.
• If the device is used as a range extender, position it between the central Zigbee device (gateway) and the sensor(s) or other devices needing extended range.

Resetting

Resetting is necessary if you wish to connect to a different gateway, perform a factory reset to resolve abnormal behavior, or clear accumulated registers and logs.

Steps for Resetting

1. Connect the Smart Plug Mini 2 to the power outlet.
2. Press and hold the button on the device.
3. Continue holding the button until the yellow LED flashes continuously, then release it.
4. After releasing the button, the yellow LED will remain lit for 2-5 seconds. During this period, do not switch off or unplug the device.

Modes

Searching Gateway Mode

The LED indicator flashes yellow every second, indicating the device is searching for a Zigbee gateway.

Normal Mode

A green LED indicates that the smart plug's output is active (the relay is on). The relay can be switched on and off by pressing the LED button.

Off Mode

When the LED button is not lit, the relay is off, meaning there is no output. The relay can be switched on and off by pressing the LED button.

Fault Finding

• In case of a power failure, the device will automatically restore its previous on/off status.
• If experiencing a weak or bad signal, try changing the location of the Smart Plug Mini 2 or your Zigbee gateway.
• If the search for a gateway times out, a short press on the LED button will restart the search.

Other Information

• The Smart Plug Mini 2 is rated for a 13 A continuous load and a 16 A (~3500 W) short-time load.
• The device will automatically switch off if the load exceeds 16 A or if the internal temperature becomes too high.

Disposal

Dispose of the product properly at the end of its life. This is electronic waste and should be recycled.

Certifications

CE Certification

The CE mark on this product confirms its compliance with applicable European Directives and harmonized standards, including:

• Radio Equipment Directive (RED) 2014/53/EU
• Low Voltage Directive (2014/35/EU)
• RoHS Directive 2015/863/EU amending 2011/65/EU

The product also bears the UKCA and WEEE symbols, indicating compliance with UK regulations and proper disposal guidelines for electronic waste.

Other Certifications

The Smart Plug Mini 2 is Zigbee 3.0 certified.

Zigbee Certified Product

All Rights Reserved

Develco Products assumes no responsibility for any errors that may appear in this manual. Develco Products reserves the right to alter hardware, software, and/or specifications detailed herein at any time without notice, and does not commit to updating the information. All trademarks are owned by their respective owners.

Distributed by:

Develco Products A/S
Tangen 6
8200 Aarhus N
Denmark
www.develcoproducts.com