MODBUS INTERNAL COM MODULE
Product End of Life Instructions
Potential disassembly risks
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
- Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA 2462 or local equivalent.
- This equipment must only be installed and serviced by qualified electrical personnel.
- Turn off all power supplying this equipment before working on or inside equipment. Lock the switchgear in the isolated position.
- Always use a properly rated voltage sensing device to confirm power is off.
- Install safety barners and display a danger sign.
- Replace all devices, doors, and covers before tuming on power to this equipment.
Failure to follow these instructions will result in death or serious injury.
End of Life Instructions
| To be dismantled | Number on drawing | Component / Material | Weight (ing) | Comment |
| To be depolluted | 1 | Electronic Board (Communication) > 10cm² | 21.33 g | VEGA PCBA |
| Recommendation | 2 | Plastic parts to be dismantled | 19.33 g | PC, PA 6, EPDM |
Product description
| Date of information release | Schneider Electric Industries SAS |
| Accessories | Schneider Electric |
| Product function | The BCM ULP circuit breaker communication module is independent of the trip unit, and it communicates two-way with the modbus network. BCM ULP module is installed behind the MicroLogic trip unit for MasterPact NT/NW, ComPact NS, and PowerPact P- and R-frame circuit breakers and is wired to the microswitches: • For manually operated devices: 1.OF, SDE, and SD contacts • For electrically operated devices: 1.OF, SDE, PF, and CH contacts 2.Connection kit to the MX1 and XF communicating voltage releases The representative product used for the analysis is MODBUS INTERNAL COM MODULE (ref. 33106) and Breaker ULP cord L=1.3m (ref. LV434196). |
| Product reference | 33106, LV434196 |
| Total representative product mass | 69.4 g |
| Representative product dimensions | 87.2 mm x 56.4 mm x 18 mm |
| Manufacturer identification | MODBUS INTERNAL COM MODULE is connected to the ULP devices via the MEDIUM BREAKER ULP CORD. Ulp cord available in three lengths 0.35 m (LV434195), 1.3 m ( LV434196), and 3 m (LV434197), 33119 – Terminal Block |
| Brand name | Nov-23 |
Additional information
| Legal information | This product family is in the scope of European Union directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). The product family must be disposed according to the legislation of the country. This document is intended for use by end of life recyclers or treatment facilities. It provides the basic information to assure an appropriate end of life treatment for the components and materials of the product. | |
| In case of special transportation: transportation method | NO | |
| Recyclability potential | 4% | Recyclability rate has been calculated based on REEECY’LAB tool developed by Ecosystem, for components/materials not covered by the tool, data from the “ECO’DEEE recyclability and recoverability calculation method” was taken. If no data was found a conservative assumption was used (0% recyclability). |
www.se.com ENVEOLI2306024_V1
RCS Nanterre 954 503 439
Capital social 896 313 776 €
Country Customer Care Center
http://www.schneider-electric.com/contact
35, rue Joseph Monier
CS 30323
F- 92500 Rueil Malmaison Cedex
Schneider Electric Industries SAS
Published by Schneider Electric
© 2023 – Schneider Electric – All rights reserved
11/2023
Documents / Resources
 | Schneider Electric LV434196 Modbus Internal Com Module [pdf] Instructions LV434196 Modbus Internal Com Module, LV434196, Modbus Internal Com Module, Internal Com Module, Com Module |