SCHLAGE

Schlage Control™ Smart Deadbolt
with Engage Technology

Installation Instructions

Model BE467F

Schlage Control Smart Deadbolt BE467F

Warnings and Cautions

WARNING

Warnings indicate potentially hazardous conditions, which if not avoided or corrected, may cause death or serious injury.

CAUTION

Cautions indicate potentially hazardous conditions, which if not avoided or corrected, may cause minor or moderate injury. Cautions may also warn against unsafe practices.

Caution: Cautions indicate a condition that may cause equipment or property damage only.

Prepare for Installation

Tools Needed

    • Phillips screwdriver
    • Tape measure

Optional Tools

    • Flathead screwdriver
    • TorxTM driver

Important Notes

WARNING

Install and test lock with door open to avoid being locked in or out!

Caution: Use provided bolt!
DO NOT use a power drill for installation!

Check door dimensions.

See consumer.schlage.com/Service-Support for door preparation instructions if dimensions are different.

Schlage Control Smart Deadbolt BE467F - Prepare for Installation

Install the Lock

1 Install bolt and strike.

Caution: Use provided bolt!

1a Adjust bolt length, if necessary.

Measure the backset.

Schlage Control Smart Deadbolt BE467F - Adjust bolt length

If the measurement is 2C\v” (70 mm), extend the bolt.

Schlage Control Smart Deadbolt BE467F - Adjust bolt length 2

1b If desired, change to the square-corner faceplate.

Schlage Control Smart Deadbolt BE467F - Adjust bolt length 3

1c Install the bolt into the door.

CAUTION

If the bolt does not remain retracted throughout installation, locking and unlocking could be reversed, resulting in an unsecured residence.

Schlage Control Smart Deadbolt BE467F - Install the bolt into the door

1d Install the strike into the frame.
i Install all the parts shown for maximum security.

Schlage Control Smart Deadbolt BE467F - Install the strike into the frame

2 Install the outside assembly

CAUTION

If the bolt does not remain retracted throughout installation, locking and unlocking could be reversed, resulting in an unsecured residence.

2a Install the outside assembly on the outside of the door.

Schlage Control Smart Deadbolt BE467F - Install the outside assembly

3 Install the inside assembly.

CAUTION

If the cam is not in the correct position during installation, locking and unlocking could be reversed, resulting in an unsecured residence.

3a Make sure the cam on the inside assembly is in the correct position.

Schlage Control Smart Deadbolt BE467F - Install the inside assembly

3b Install the inside assembly on the inside of the door.
i Bolt must remain retracted!

Schlage Control Smart Deadbolt BE467F - Install the inside assembly on the inside of the door

3c Secure the inside assembly with two screws.
i If the screw holes are blocked by the cam, see step 3a.

Schlage Control Smart Deadbolt BE467F - Secure the inside assembly with two screws

3d Connect the cable to the inside assembly.

Schlage Control Smart Deadbolt BE467F - Connect the cable to the inside assembly

3e Install the batteries.

Schlage Control Smart Deadbolt BE467F - Install the batteries.

3f Install the inside cover.

Schlage Control Smart Deadbolt BE467F - Install the inside cover

3g Secure the inside cover with two screws.

Schlage Control Smart Deadbolt BE467F - Secure the inside cover with two screws

4 Test the Lock

4a Extend and then retract the bolt using the inside bolt throw.

Schlage Control Smart Deadbolt BE467F - Test the Lock

i Outside bolt throw should spin freely until a valid credential is presented.

5 Set up the lock.

Continue to www.schlage.com to download the Schlage Control Smart Locks User Guide.

 

Schlage Control Smart Deadbolt BE467F Installation Manual – Optimized PDF
Schlage Control Smart Deadbolt BE467F Installation Manual – Original PDF

Leave a comment

Your email address will not be published. Required fields are marked *