SCHLAGE Encode - LOGO

SCHLAGE Encode Smart WiFi Deadbolt

Quick Start Guide

Parts

SCHLAGE Encode Smart WiFi Deadbolt - Parts

Schlage - LOGO

SCHLAGE Encode Smart WiFi Deadbolt - Icon1 Start here!

schlage.com/encode-workswith
Visit: schlage.com/encode-workswith to set up and control your Schlage Encode with your smartphone.

Touchscreen

SCHLAGE Encode Smart WiFi Deadbolt - Icon Communication Icon

  • Flashes when the lock is connecting to WiFi to check for updates.

SCHLAGE Encode Smart WiFi Deadbolt - Icon2 Low Battey Icon

  • Flashes after code are entered when the battery is low.
  • Solid when the battery is critical. The lock will not work without new batteries.

SCHLAGE Encode Smart WiFi Deadbolt - Remote

 Programming and Input LED

  • Flashes white on every digit that is entered.
  • Amber when using manual programming mode.

SCHLAGE Encode Smart WiFi Deadbolt - Icon4 Home Button and Checkmark Icon

  • Turns on the keypad backlight.
  • Starts WiFi connection process.
  • Checkmark flashes when the code entered is correct.
  • Checkmark flashes when manual programming is successful.

SCHLAGE Encode Smart WiFi Deadbolt - Icon5 Lock Button and “X” Icon

  • Locks the lock.
  • Turns on the keypad backlight if the lock is locked.
  • “X” flashes for the wrong user code.

Tools

SCHLAGE Encode Smart WiFi Deadbolt - Taster Phillips screwdriver Don’t use a power drill!

Steep:1

Remove existing lock.
Remove the entire deadbolt, including the bolt. You may also want to remove the strike. A standard Schlage deadbolt is shown. Check with your specific deadbolt manufacturer if you need help.

SCHLAGE Encode Smart WiFi Deadbolt - Lock

Step: 2
Need Help?
Visit: schlage.com/faqs-encode.
Install the bolt. You may have to adjust your bolt length. Make sure the slot in the bolt is centered in the hole.

SCHLAGE Encode Smart WiFi Deadbolt - Bolt

Steep:3
Need Help?
Trouble installing the strike reinforcer?
Visit: schlage.com/faqs-encode and follow interactive instructions.
Install the strike into the door frame. If you have a window next to your door, you may not be able to use the long wood screws to install the reinforcer.

SCHLAGE Encode Smart WiFi Deadbolt - Door Frame

Steep:4
Is it hard to install the touchscreen? Is the tailpiece not installed correctly? If your through-hole seems too small, you may need to remove the spacer.
Visit: schlage.com/faqs-encode.

Install the touchscreen.
Route the cable through the door BELOW the bolt. Align the tailpiece as shown and push the touchscreen onto the door.

SCHLAGE Encode Smart WiFi Deadbolt - Touchscreen

Steep: 5

SCHLAGE Encode Smart WiFi Deadbolt - Taster Phillips screwdriver Don’t use a power drill! You may damage your lock!

Install the backplate.
Route the cable under the bolt and through the hole on the bottom of the backplate. Secure the backplate with screws. Make sure the outside touchscreen is straight before tightening screws all the way.
SCHLAGE Encode Smart WiFi Deadbolt - Backplate

Steep:6
Connect the cable.
Tuck the cable and connector in the space above the spindle.

SCHLAGE Encode Smart WiFi Deadbolt - Connect Cable

Steep: 7

SCHLAGE Encode Smart WiFi Deadbolt - Taster Phillips screwdriver Don’t use a power drill! You may damage your lock!

Secure the lock to the door.
If the bump on the tailpiece doesn’t align with the slot in the back of the inside assembly, make sure your thumbturn is vertical (up and down).

SCHLAGE Encode Smart WiFi Deadbolt - Lock to the door

Steep:8
Install batteries and slide the cover on.

SCHLAGE Encode Smart WiFi Deadbolt - Batteries and slide cover

That wasn’t so bad, was it?
Your lock is now installed! Remember, you still have to set up your lock to use it.

Steep:9
Set up your lock.

SCHLAGE Encode Smart WiFi Deadbolt - Final test

  1. Open your door!
  2. Enter one of the two default user codes.
  3. Your lock will enter a setup routine. When the bolt stops moving, the setup is complete.

Final test!

  1. Close your door.
  2. Extend and retract the bolt using the inside thumb turn.
  3. Make sure the bolt retracts smoothly.
  4. Open your door.
  5. Extend the bolt using the inside thumb turn.
  6. Now enter a user code a the touchscreen.

Need Help?
If the bolt doesn’t extend or retract during testing, visit schlage.com/faqs-encode.

Schlage - LOGO

Now that your lock is installed
you can use a smart home system to lock and unlock your door from anywhere and add user codes for guests and household members.
schlage.com/encode-workswith
Visit: schlage.com/encode-workswith for a list of compatible smart home apps that allow you to control your Schlage Encode with your smartphone.

Lock and unlock

To lock your door just tap the lock icon.
You can also lock your door from inside by turning the thumb turn toward the door edge.

SCHLAGE Encode Smart WiFi Deadbolt - Lock

To unlock your door enter a user code.
You can also unlock your door from inside by turning the thumb turn away from the door edge.

SCHLAGE Encode Smart WiFi Deadbolt - Unlock

Questions about your new Schlage Encode Smart WiFi Deadbolt?
Please don’t return it to the store! Let us help you first!
www.schlage.com/faqs-encode

Allegion - LOGO

© Allegion 2018 Printed in U.S.A P518-415 Rev.08/18-d

SCHLAGE Encode Smart WiFi Deadbolt - BercodeP518-415

Documents / Resources

SCHLAGE Encode Smart WiFi Deadbolt [pdf] User Guide
BE489WB CAM 619, Encode Smart WiFi Deadbolt, Encode

Leave a comment

Your email address will not be published.