SCHLAGE logo

SCHLAGE AD-200 Offline Commercial Keypad Lock

SCHLAGE AD-200 Offline Commercial Keypad Lock

Installation InstructionsSCHLAGE AD-200 Offline Commercial Keypad Lock fig 1

  1. Prepare door.
    IMPORTANT! See template. Additional door preparation may be required.
  2. Identify model of lock.
    AD-200 Printed on box label. Choose steps to perform by models listed in corner.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 2
  3. Install door position switch (DPS).
    Ensure alignment on door and jamb.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 3
  4. Route RS-485 cable and power wires.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 4
  5. If not using batteries (standard option), route power wires.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 5
  6. When retrofitting, install RX switch. Install in existing 98/99 exit device. SCHLAGE AD-200 Offline Commercial Keypad Lock fig 6
  7. Install sex bolts to secure device.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 7
  8. Install grommet. SCHLAGE AD-200 Offline Commercial Keypad Lock fig 8
  9. Route RX wires.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 9
  10. Install device per manufacturer instructions.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 10
    For proper function, cam must be in down position.
  11. Install spindle into assemblySCHLAGE AD-200 Offline Commercial Keypad Lock fig 11
  12. Install reader.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 12
  13. Check lever handing.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 13
  14. Install cylinder and lever.
    Verify tailpiece is horizontal.
    Keyed LeverSCHLAGE AD-200 Offline Commercial Keypad Lock fig 14
  15. Install outside assembly.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 15
  16. Install inside assembly.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 16
  17. Connect white DPS wires.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 17
  18. Connect ribbon cable.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 18
  19. If RX, insert plug.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 19
  20. Install RS-485 communication module.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 20
    Install lower cover.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 21
  21. Install wireless communication module.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 22
  22. Apply power, AD-200/250/400 only. Optional Torx® security screws are included.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 23
    Hardwired option:
    See user guide for wiring details.
  23. Carefully remove insulator strip from battery.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 24
  24. Install cover and screws.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 25
  25. Set up lock. After installing the lock, see the user guide for setup and operation.

Lever removalSCHLAGE AD-200 Offline Commercial Keypad Lock fig 26

Changing the cylinder’s tailpieceSCHLAGE AD-200 Offline Commercial Keypad Lock fig 27

Rehanding
  1. Remove USB plug.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 28.
  2. Remove cover from baseplate.
    NOTE: on keypad only applications, reader is not removable!SCHLAGE AD-200 Offline Commercial Keypad Lock fig 29
  3. Remove spring cage.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 30
  4. Move lever stop to opposite side − Align arrow with latch.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 31
  5. Reinstall springcage.
    IMPORTANT: Verify that the correct size screw is used.SCHLAGE AD-200 Offline Commercial Keypad Lock fig 32
  6. Reassemble cover, baseplate, and mounting plate.
    IMPORTANT: Do not pinch the ribbon cable during reassembly.

Documents / Resources

SCHLAGE AD-200 Offline Commercial Keypad Lock [pdf] Instruction Manual
AD-200, AD-250, AD-300, AD-400, AD-200 Offline Commercial Keypad Lock, AD-200, Offline Commercial Keypad Lock

References

Leave a comment

Your email address will not be published.