SCHEIDT BACHMANN O5K-SCR3 Smartcard Reader

Revisions

The Module

• Product Marketing Name: Smartcard Reader 3.0
• HVIN: 03870610
• FVIN: 07346220
• FCC ID: O5K-SCR3
• IC: 8312A-SCR3

Connections
Pinning of the 52 pin PCIe Edge Connector (ST100)

Interfaces
The main communication Interface to the Host system is USB 2.0. Make sure that requirements made by the USB-Standard are considered.

Environmental conditions

Temperature:

• Operating temperature: -25 to +60°C
• Storage temperature: -30 to +60°C

Interfaces
The main communication Interface to the Host system is USB 2.0. Make sure that requirements made by the USB-Standard are considered.

Environmental conditions

Temperature:

• Operating temperature: -25 to +60°C
• Storage temperature: -30 to +60°C

Humidity:

• 5% to 95% not condensing. The module is sensitive to ESD. Take care while handling these modules.

Power supply

• Supply voltage for digital circuits: 3.3V +/-5%.
• Make sure the voltage is accurate. Good filter practice has to be used.
• RF Supply voltage: 5V +/-5%.
  Make sure the voltage is accurate. Good filter practice has to be used.

Supply voltage for digital circuits: 3.3V +/-5%. Make sure the voltage is accurate. Good filter practice has to be used.

RF Supply voltage: 5V +/-5%. Make sure the voltage is accurate. Good filter practice has to be used. RFID systems require a very high level supply quality. Use linear regulators with high precision and high control speed whenever possible. When using switching power supplies make sure the switching speed is above 500 kHz and use an EMC-optimized layout as well as shielded inductors.

The voltage for digital circuits should be applied first.

Current consumption:

• Max. 300mA at 3.3V.
• Max. 800mA at 5V.

Antennas

There are two RF paths with different antenna connectors. That ensures the right connections for antenna installation. Antennas made by the grantee used for this certification are the only Antennas which should be used in combination with the device. The antenna of the module should not be removed, replaced nor modified. The antenna must not be co-located or operating in conjunction with any other antenna or transmitter within 20cm. No other antenna than the ones from the certification must be used.

Compliance statements

In the manual of the host product, the following statements have to be written in a prominent location:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTICE:
Changes or modifications made to this equipment not expressly approved by (Scheidt & Bachmann GmbH) may void the FCC authorization to operate this equipment.

Certification

FCC (USA)
The FareGo SCR Module complies with Part 15 of the FCC Rules. To fulfill all FCC requirements the integrator must comply with the following regulations:

• The integrator must make sure that the end device is labelled according to FCC requirements. This means that the end device must have a clearly visible label on the outside of the product with at least the following content:

Contains FCC ID: O5K-SCR3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   • The integrator must test the final product to comply with FCC regulations regarding unintentional radiators (FCC sections 15.107 and 15.109) before declaring FCC compliance of his own product.

ATTENTION:
Changes or modifications not expressly approved by Scheidt & Bachmann GmbH could void the user’s authority to operate the equipment.

IC (Canada) 

Labelling requirements for Industry Canada (IC) are similar to those of the FCC. A visible label on the outside of the final product must display at least the following text: Contains IC: 8312A-SCR3 The integrator is responsible for its product to comply with IC ICES-003 & FCC Part 15, Sub. B – Unintentional Radiators. ICES-003 is the same as FCC Part 15 Sub. B and Industry Canada accept the FCC test report or CISPR 22 test report for compliance with ICES-003.

Contact

• Scheidt & Bachmann GmbH
• Breite Str. 132
• 41238 Mönchengladbach
• Germany
• Tel.: +49 (0)2166 / 266 – 0
• www.scheidt-bachmann.com

Documents / Resources

SCHEIDT BACHMANN O5K-SCR3 Smartcard Reader [pdf] User Guide O5KSCR3, scr3, O5K-SCR3 Smartcard Reader, O5K-SCR3, Smartcard Reader, Reader

References

• User Manual