“
Product Information
Specifications
- Product Name: Scandinavian Trapeze
- Design: Scandinavian-style trapeze
- Intended Use: Indoor use
- Recommended Age: 18 months to 6 years old
- Maximum Load Capacity: 60 kg / 132 lbs
Product Usage Instructions
Safety Measures
To ensure stability and prevent overtipping, securely anchor the
structure to the floor with the provided anchors.
Assembly Instructions
- Attach front and back bases to the right base using screws and
a key. - Attach the left base to the front and back bases using screws
and a key. - Attach ladder sidewalls to the rods using self-tapping
screws. - Attach stands with rods using screws and a key.
- Attach upper bases to the rods using self-tapping screws and a
key. - Insert the rope into the stands for the rope ladder and secure
with screws and a key. - Route the rope through the sidewalls following the provided
instructions.
Care and Maintenance
Regularly inspect the trapeze for any signs of damage or wear.
Clean with a damp cloth when necessary.
Frequently Asked Questions (FAQ)
A: The recommended age for children using the trapeze is from 18
months to 6 years old.
Q: What is the maximum load capacity of the trapeze?
A: The trapeze has a maximum load capacity of 60 kg or 132
lbs.
“`
EN
USER MANUAL
SCANDINAVIAN TRAPEZE
1
WARNING! Read this manual carefully before use
SCOPE OF APPLICATION
This product is a Scandinavian-style trapeze designed for indoor use. It is suitable for children under adult supervision. Improper assembly or use may cause injury. Carefully follow the instructions for safe installation and use. Recommended age: For children from 18 months to 6 years old. Maximum Load Capacity: 60 kg / 132 lbs.
TERMS OF USE
– Only for indoor use. – For domestic use. – Tighten the bolts every 2 months. – Use not more that 1 rope accessory per time. – A safety mat or soft landind area is recommended to minimize injury risks. – The product has no expiration term but change the product or the details of the product immediately if any damage occur. – 2 years warranty. Note: – Warranty does not apply if the product is being damaged due to the weather conditions, as it is for indoor use only; – Manufacturer reserves the right to make structural changes to the product without prior notice, provided such changes do not affect product’s functionality, safety, and key features; – In case of any inappropriate use or failure to comply with the instructions, the manufacturer and seller shall bear no responsibility and the warranty shall not apply. – Responsibility for any damage incurred by children during play on the furniture rests with the supervising adults; if a child is injured while playing with the product, please treat the wound and consult a doctor.
SAFETY MEASURES
– The product must be assembled by an adult. – In disassembled state the product contains small parts constituting a choking hazard for the kid. After the assembly, ensure all screws and fastenings are securely tightened. – To be used under the direct supervision of an adult only. Do not leave the kid alone with the product. – Do not exceed the maximum weight limit. – Do not use at uneven and hard floor. – Do not use the product if it has any visible damage or positioned abnormally. – Do not use the product on the wet or contaminated floor. – Do not place near hazards: ensure the climber is located at least 2m away from windows, sharp corners, hard furniture or any other hazards. The area around the climber should be clear and safe. – Do not place the product close to the sources of radiant heat or under the direct sun rays. – Responsibility for any damage incurred by children during play on the furniture rests with the supervising adults. If a child is injured while playing with the product, please treat the wound and consult a doctor. – Avoid modifying the ladder or adding homemade extensions unless you are sure they are safe and compatible. Modifications can affect the stability and safety of a climber. – In case of any inappropriate use or failure to comply with the instructions, the Manufacturer and Seller shall bear no responsibility and the warranty will not apply. – To prevent overcrowding and ensure stability, limit the number of children using the climber at one time based on the size and design of the climber. – Proper Footwear: Ensure that children wear appropriate footwear to prevent slips and falls. Shoes should have a good grip and be suitable for physical activity. – Do not let the children to climb onto the upper side of the product. It is meant as a climbing frame, not a climbing platform.
2
– To ensure the stability of a construction and prevent overtipping, securely anchor the structure to the floor with the anchors that are added to the assembly kit.
CARE AND MAINTENANCE
– To clean the item, wipe it with a damp cloth or wet wipes. – Avoid excessive moisture – water can penetrate into seams or microcracks and cause damage to wood; in case of spillage on the product – wipe dry. – Do not use abrasive sponges, aggressive detergents, alcohol or acetone. – Do not leave the product outdoors or near heat sources (batteries, fireplaces). – With the appearance of scuffs or fading, you can easily restore a layer of varnish or paint – use the same water base that the product was treated with. Clean the surface and grind lightly before re-coating. – If the product is not used for a long time, store it in a dry room with moderate humidity (40-60%); avoid storage in damp or uninsulated areas.
ASSEMBLY INSTRUCTIONS
1 – Right base
2 – Left base
3 – Front base
1 pc. 4 – Back base
1 pc. 5 – Ladder stand 1
1 pc. 6 – Ladder stand 2
1 pc. 7 – Stand with the rod 1
1 pc. 8 – Stand with the rod 2
1 pc. 9 – Corner stand
1 pc. 10 – Upper base 1
1 pc. 11 – Upper base 2
1 pc. 12 – Right connector
1 pc. 13 – Left connector
1 pc.
1 pc.
14 – Sidewall of additional ladder
1 pc.
15 – Right stand for rope ladder
2 pcs.
1 pc.
16 – Left stand for rope ladder 17 – Rod for the rope
18 – Long rope (3.5 m/137.79 in)
1 pc.
19 – Short tope (1.7m/66,92 in)
3 pcs. 20 – Long rod
1 pc. 21 – Short rod
3 pcs.
a – Self-tapping screw TORX 6×50
16 pcs.
b – Self-tapping screw TORX 6×80
4 pcs. c – TORX key T30
62 pcs. d – Angle 27×27
11 pcs.
e – Self-tapping screw 3.5×16
f – Dowel 6×40
1 pc.
4 pcs.
1
4 pcs.
4 pcs.
Take front and back bases (3, 4) and attach them to the right base (1) with the help of screws (a) and a key (c). See Pic. 1.
2
Take a left base (2) and using the screws (a) and hex key (c) attach it to the front and back bases (3, 4). See Pic. 2.
4
3
20
Take the ladder sidewalls (5, 6) and using self-tapping screws (a) and a key (c) attach the rods (20). See Pic. 3. Do not screw in the screw marked with exclamation mark (!).
4
Take the stands with the rod (7, 8) and
using the screws (a) and hex key (c)
20
attach the rods (20). See Pic. 4. Do not screw in the screw marked
with exclamation mark (!).
5
Take the upper bases (10, 11) and
20
attach the rods (20) using the
self-tapping screws (a) and a key (c).
See Pic. 5.
5
6
Take the rod for rope (17) and insert them inbetween the stands for rope ladder (15, 16). Join them using self-tapping screws (a) and a key (c). See Pic. 6. ! – Do not screw the hardware into the hole with exclamation mark.
16
17
15
17
17
7
Route of the rope
Take the rope (18), insert it into the hole in sidewall and route it to the hole in the opposite sidewall. See Pic. 7.
Start the rope
Pull the rope and tie a knot following the steps (1-3). Leave 2 cm/0,79 in of rope in reserve at the knot. See Pic. 8.
Tie a knot
Step 1 Step 2 Step 3
6
Start the rope
9
Route the rope into the groove in the sidewall and further to the hole in the opposite sidewall. See Pic. 9.
Route of the rope
10
Route of the rope
Route the rope into the groove in the sidewall and further to the hole in the opposite sidewall. See Pic. 9.
Start the rope
Start the rope
11
Route the rope into the groove in the sidewall and further to the hole in the opposite sidewall. See Pic. 11. Route of the rope
7
12
Route of the rope Route the rope into the groove in the sidewall and further to the hole in the opposite sidewall. See Pic. 12.
Start the rope
Start the rope
13
14
Route the rope into the groove in the sidewall and further to the hole in the opposite sidewall. See Pic. 14.
Route of the rope Route the rope into the groove in the sidewall and further to the hole in the opposite sidewall. See Pic. 13.
Tie a knot
8
15
Insert the rope (19) into the hole. Tie a knot following the steps (1-3) as shown in the Pic. 8. Leave 2 cm/0,79 in of rope in reserve at the knot. See Pic. 15.
16
Tie a knot
Tie a knot at the horizontal tope following the steps (1-4). Route the rope till the end, tying a knot at every horixontal rope. In the end, tie a know following the steps (1-3, see Pic. 8). Leave 2 cm/0,79 in of rope in reserve at the knot. See Pic. 16.
Step 1
Step 2
Step 3
Step 4
Tie a knot
17
Tie a knot
Tie a knot Tie a knot
Repeat the actions shown in the Pic. 16 for 2 other paths of short rope (19). Tie knots in the end in the same way, by the steps (1-3) as shown in the Pic 8. Leave 2 cm/0,79 in of rope in reserve at the knot. See Pic. 17.
9
18
Take the assembled rope ladder and attach it to the pre-assembled base structure using self-tapping screws (a) and a key (c). See Pic. 18.
Pic. 4
Pic. 17
Pic. 2
19
Take the pre-assembled construction, shown in the Pic. 4. Attach it to the previousle assembled construction (see Pic. 18) using self-tapping screws (d) and a key (c). See Pic. 19.
20
Take the pre-assembled construction, shown in the Pic. 3 and a corner stand (9). Attach them to previously assembled construction (see Pic. 19) using self-tapping screws (a) and a key (c). See Pic. 20.
10
Pic. 3
Pic. 5
22
Take right and left connectots (12, 13) and attach them to the construction shown in the Pic. 21. use self-tapping screws (b) and key (c). See Pic. 22.
21
Attach the construction assebled due to the Pic. 5 to the construction assembled due to the Pic. 20. Use self-tapping screws (a) and a key (c). See Pic. 21.
23
20
Take the sidewalls of additional
ladder (14) and join them with the
long rods (20) using screws (c) and
a key (c). See Pic. 23.
11
24
21
Attach the additional ladder (Pic. 23) to the main trapeze construction with short rods (21) using screws (a) and key (c).
25
Anchor the construction to the floor using angles (d), screws (e) and dowels (f). See Pic. 25
POSSIBLE ADD-ONS
Soft mattress
Rope with round platform
Gymnastic rings
12
Rope with spheres
Swingt
How to attach: instruction
1 – Ramp
2 – Hook
Ramp
a – Confirmat screw 5×40 mm
b – 4 mm hex key
1 pc.
a a
2.2 a a
4 pcs.
2.2
2.1
2.2
a a
2.2
a ab
8pcs. + 1 pc. spare
1 pc.
Attach the hooks (2) to the ramp (1) using the confirmat screws (a) and hex key (b). See the pic.
DISPOSAL AND ENVIRONMENTAL INFORMATION
Dispose of the product in accordance with local waste regulations. Components can be recycled where applicable.
MANUFACTURER
Look for manufacturer information on the product packaging.
13
CONTACT INFORMATION
+ 1 804-500-1025 (USA, EN) + 38 050 067 71 15 (UA) unterstutzung@woodandhearts.de support.official@woodandhearts.com woodandhearts.de woodandhearts.com
14
Documents / Resources
 |
WOOD and HEARTS W008 Scandinavian Trapeze [pdf] User Manual W008 Scandinavian Trapeze, W008, Scandinavian Trapeze, Trapeze |