sauermann logo

sauermann HM 110 Humidity Sensor

sauermann HM 110 Humidity Sensor fig 1

Quick Start Guide

Humidity transmittersauermann HM 110 Humidity Sensor fig 2sauermann HM 110 Humidity Sensor fig 3sauermann HM 110 Humidity Sensor fig 4

Operating temperature, protection of the instruments and information about storage
Conditions of use (°C/%RH/m): from 0 to +50 °C; in non-condensing conditions. From 0 to 2000 m. Protection: IP65 (remote and duct models); IP20 (ambient model)
Storage temperature: from -10 to +70 °C.

Dimensions

  • Duct model
  • Ambient model
  • Remote model

sauermann HM 110 Humidity Sensor fig 5sauermann HM 110 Humidity Sensor fig 6

Used symbols

For your safety and in order to avoid any damage of the device, please follow the procedure described in this document and read carefully the notes preceded by the following symbol:
The following symbol will also be used in this document, please read carefully the information notes indicated after this symbol:

Connections

  1. Active switch (S1)
  2. Inactive switch
  3. LCC-S software connection
  4. Output terminal block
  5. Power supply terminal block
  6. Cable glandsauermann HM 110 Humidity Sensor fig 7sauermann HM 110 Humidity Sensor fig 8
  • Inside the front housing
  • Removable front face
  • Fixed back housing

Electrical connections as per NFC15-100 standard

This connection must be made by a qualified and trained technician. To make the connection, the transmitter must not be energized.

2 wires

sauermann HM 110 Humidity Sensor fig 11

3 wiressauermann HM 110 Humidity Sensor fig 10

4 wiressauermann HM 110 Humidity Sensor fig 9

Configuration via LCC-S software (option)

An easy and friendly configuration with the software!
It is possible to configure the device.
For example, the instrument could be configured from 30 to 50% RH.
In order to compensate a possible drift of the transmitter, it is possible to add an offset to the displayed value by the HM110 instrument: it shows 48% RH, a standard instrument shows 45% RH. It is then possible, through the software, to integrate an offset of -3 to the displayed value by the HM 110 instrument
To access the configuration via software:
Connect the cable of the LCC-S to the connection of the transmitter.

PC configurationsauermann HM 110 Humidity Sensor fig 12

  1. Please refer to the
  2. optional LCC-S
  3. software to make the
  4. configuration.

Active switch (S1)

Mounting

To mount the transmitter, mount the ABS plate on the wall (drilling: 6 mm, screws and pins are supplied).
Insert the transmitter on the fixing plate (see A on the drawing beside). Rotate the housing in clockwise direction until you hear a “click” which confirms that the transmitter is correctly installed. sauermann HM 110 Humidity Sensor fig 13

The model with ambient probe does not have any mounting plate. 4 fixing holes are present inside the back housing. Use them to install the transmitter on the required location.

  • Maintenance: Please avoid any aggressive solvent. Please protect the transmitter and its probes from any cleaning product containing formalin, that may be used for cleaning rooms or ducts.
  • Precautions for use: please always use the device in accordance with its intended use and within parameters described in the technical features in order not to compromise the protection ensured by the device.

Customer service portal / Portail service clients Portal de servicio al cliente / Portale servizio clienti Use our Customer service portal to contact us Utilisez notre Portail service clients pour nous contacter
https://sauermann-en.custhelp.com

Documents / Resources

sauermann HM 110 Humidity Sensor [pdf] User Guide
HM 110, Humidity Sensor, HM 110 Humidity Sensor

References

Leave a comment

Your email address will not be published.