SAMSUNG QM32R-B 32 Inch LED-backlit LCD Display User Manual

QM32R-B 32 Inch LED-backlit LCD Display

Smart Signage User Manual (By Model)
This manual provides information about your Smart Signage including supported types and product specifications per model.
QBR (QB43R QB49R QB50R QB55R QB65R QB75R QB85R QB98R) QER (QE82R) QMR (QM32R QM43R QM49R QM50R QM55R QM65R QM75R QM85R) QMR-T (QM32R-T QM43R-T QM55R-T)
The colour and the appearance may differ depending on the product, and the content in the manual is subject to change without prior notice to improve the performance. Recommended hours of use per day for the QBR models (except for QB98R), QM32R-T, and QER models is less than 16 hours. If the product is used for longer than 16 hours a day, the warranty may be void. An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e., where the user manual has not been read). (b) You bring the unit to a repair centre, but it is found that the product has no defect (i.e., where the user manual has not been read). You will be informed of the administration fee amount before a technician visits.
© Samsung Samsung owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung is prohibited. Trademarks other than Samsung are property of their respective owners.

Table of contents

Preparations

Checking the Components

3

Parts

4

QM32R/Q*43R/Q*49R/Q*50R/Q*55R/

Q*65R/Q*75R/Q*85R/QE82R/QM32R-T/

QM43R-T/QM55R-T

4

QB98R

5

Anti-theft Lock

6

Ports

7

Q*43R/Q*49R/Q*50R/Q*55R/Q*65R/

Q*75R/Q*85R/QE82R

7

QM32R

8

QB98R

9

QM32R-T

10

QM43R-T/QM55R-T

11

Control menu

12

Administrator menu (Supported models:

QMR-T)

13

Precautions when handling the panel

14

Before Installing the Product (Installation

Guide)

15

Tilting Angle and Rotation

15

Ventilation

15

Installing the Wall Mount

16

Preparing before installing Wall-Mount

16

Installing the Wall Mount

16

Wall Mount Kit Specifications (VESA)

17

Using a touchscreen monitor (Supported models: QMR-T)

Touchscreen monitor

18

Read below before using the product

18

Connecting the touch overlay

18

Connecting the touchscreen monitor

19

Connecting to a PC

19

Connecting to a laptop or tablet PC

19

Configuring the touchscreen monitor

settings

20

Calibration

20

Specifications

General

22

Preset Timing Modes

25

Appendix

Licence

26

2

Chapter 01
Preparations

Checking the Components

” Contact the vendor where you purchased the product if any components are missing.
” The appearance of the components may differ from the images shown.
” A stand is not provided with the product. To install a stand, you can purchase one separately.
” The RS232C adapter can be used to connect to another monitor using the D-SUB (9-pin) type RS232C cable.

Quick Setup Guide
Batteries (AAA x 2) (Not available in some locations)

Warranty card (Not available in some locations)
Remote Control

Regulatory guide RS232C adapter

Power cord
HOLDER-CABLE (Supported models: Q*65R, Q*75R, Q*85R, QB98R, QE82R)

Holder-Ring x 4
(Supported models: Q*43R, Q*49R, Q*50R, Q*55R, Q*65R,
Q*75R, QM43R-T, QM55R-T)

TOUCH OUT cable x 2 (Supported models: QMR-T)

3

Parts
QM32R/Q*43R/Q*49R/Q*50R/Q*55R/ Q*65R/Q*75R/Q*85R/QE82R/QM32R-T/ QM43R-T/QM55R-T
Remote sensor

” The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Parts

Description

Remote sensor

Press a button on the remote control pointing at the sensor on the front of the product to perform the corresponding function.
” Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.

Power button

Turns the product on or off.

Use the remote control within 2.5 m to 4 m from the sensor on the product at an angle of 30° from the left and right.
” To enhance the IR receiver performance, connect an external IR cable (sold separately) to the IR IN port.

Power button Power indicator

2.5 m 30° 30°2.5 m 4 m

Speaker
4

QB98R
Speaker

ON/OFF
Spacer logo Remote sensor & Power button

” The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Parts
Spacer logo
Remote sensor

Description
Do not pull on the spacer logo using force. The logo may tear or break off. Press a button on the remote control pointing at the bottom of the product face to perform the function. The remote control sensor is located on the bottom of the product. ” Using other display devices in the same space as the remote control of this product
can cause the other display devices to be inadvertently controlled.
To use remote/eco sensor, make sure the sliding power button is protruding from the bottom of the product.

Power button

To use the power button, make sure the sliding power button is not protruding from the bottom of the product.

Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30° from the left and right. ” To enhance the IR receiver performance, connect an external IR cable (sold separately) to the IR IN port.

5

Anti-theft Lock
” An anti-theft lock allows you to use the product securely even in public places. ” The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. ” The following images are for reference only. Real-life situations may differ from what is shown in the images. ” Supported model: QB98R
To lock an anti-theft locking device:
1 Fix the cable of your anti-theft locking device to a heavy object such as a desk. 2 Put one end of the cable through the loop on the other end. 3 Insert the locking device into the anti-theft lock slot at the back of the product. 4 Lock the locking device.
­ An anti-theft locking device can be purchased separately. ­ Refer to the user guide provided with your anti-theft locking device for details. ­ Anti-theft locking devices can be purchased at electronics retailers or online.
6

Ports

Q*43R/Q*49R/Q*50R/Q*55R/Q*65R/ Q*75R/Q*85R/QE82R
” The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

QB43R / QB49R / QB50R / QB55R / QB65R / QB75R / QB85R

QE82R

QM43R / QM49R / QM50R / QM55R / QM65R / QM75R / QM85R

Port
USB 1 ¨(1.0A)
RJ45
RS232C IN DVI/MAGICINFO IN DVI IN HDMI IN 1 (ARC) HDMI IN 2 HDMI IN 2 (DAISY CHAIN IN) DP IN (DAISY CHAIN IN) HDMI OUT (DAISY CHAIN OUT)
USB 2(0.5A)
DVI/HDMI AUDIO IN AUDIO OUT IR IN RS232C OUT

Description
Connect to a USB memory device. ” The USB ports on the product accept a maximum constant current of 1.0A.
If the maximum value is exceeded, USB ports may not work. Connects to MDC and the Internet using a LAN cable. (10/100 Mbps) ” Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair. Connects to MDC using an RS232C adapter.
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable. MAGICINFO IN: Connects to a network box using DP-DVI cable to use Magicinfo.
Connects to a source device using a HDMI cable or HDMI-DVI cable.
· Connects to a source device using a HDMI cable or HDMI-DVI cable. · Connects to another product using a HDMI cable. Connects to a PC using a DP cable. Connects to another product using a HDMI cable. Connect to a USB memory device. ” The USB ports on the product accept a maximum constant current of
0.5A. If the maximum value is exceeded, USB ports may not work. Receives sound from a source device via an audio cable. Outputs sound to an audio device via an audio cable. Connects to an external IR cable that receives signals from the remote control. Connects to MDC using an RS232C adapter.

7

QM32R
” The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Port
USB 1 ¨(1.0A)
HDMI IN 1 (ARC)
RJ45
RS232C IN HDMI IN 2 (DAISY CHAIN IN) DP IN (DAISY CHAIN IN) HDMI OUT (DAISY CHAIN OUT)
USB 2(0.5A)
AUDIO OUT IR IN RS232C OUT

Description
Connect to a USB memory device. ” The USB ports on the product accept a maximum constant current of 1.0A.
If the maximum value is exceeded, USB ports may not work.
Connects to a source device using a HDMI cable or HDMI-DVI cable.
Connects to MDC and the Internet using a LAN cable. (10/100 Mbps) ” Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair.
Connects to MDC using an RS232C adapter.
· Connects to a source device using a HDMI cable or HDMI-DVI cable. · Connects to another product using a HDMI cable.
Connects to a PC using a DP cable.
Connects to another product using a HDMI cable.
Connect to a USB memory device. ” The USB ports on the product accept a maximum constant current of
0.5A. If the maximum value is exceeded, USB ports may not work.
Outputs sound to an audio device via an audio cable.
Connects to an external IR cable that receives signals from the remote control.
Connects to MDC using an RS232C adapter.

8

QB98R
” The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

RJ45

Port

USB 1 ¨(1.0A)
DVI/MAGICINFO IN RS232C IN RS232C OUT DVI/HDMI AUDIO IN HDMI IN 1 (ARC) HDMI IN 2 (DAISY CHAIN IN) DP IN (DAISY CHAIN IN) HDMI OUT (DAISY CHAIN OUT)
USB 2(0.5A)
AUDIO OUT IR IN

Description
Connects to MDC and the Internet using a LAN cable. (10/100 Mbps) ” Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair.
Connect to a USB memory device. ” The USB ports on the product accept a maximum constant current of 1.0A.
If the maximum value is exceeded, USB ports may not work.
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable. MAGICINFO IN: Connects to a network box using DP-DVI cable to use Magicinfo.
Connects to MDC using an RS232C adapter.
Connects to MDC using an RS232C adapter.
Receives sound from a source device via an audio cable.
Connects to a source device using a HDMI cable or HDMI-DVI cable.
· Connects to a source device using a HDMI cable or HDMI-DVI cable. · Connects to another product using a HDMI cable. Connects to a PC using a DP cable.
Connects to another product using a HDMI cable.
Connect to a USB memory device. ” The USB ports on the product accept a maximum constant current of
0.5A. If the maximum value is exceeded, USB ports may not work.
Outputs sound to an audio device via an audio cable.
Connects to an external IR cable that receives signals from the remote control.

9

QM32R-T
” The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Port
USB 1 ¨(1.0A)
HDMI IN 1 (ARC)
RJ45
RS232C IN HDMI IN 2 (DAISY CHAIN IN) DP IN (DAISY CHAIN IN) HDMI OUT (DAISY CHAIN OUT)
USB 2(0.5A)
AUDIO OUT IR IN RS232C OUT TOUCH OUT SCREEN TOUCH OUT PC

Description
Connect to a USB memory device or TOUCH OUT cable. ” The USB ports on the product accept a maximum constant current of 1.0A.
If the maximum value is exceeded, USB ports may not work.
Connects to a source device using a HDMI cable or HDMI-DVI cable.
Connects to MDC and the Internet using a LAN cable. (10/100 Mbps) ” Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair.
Connects to MDC using an RS232C adapter.
· Connects to a source device using a HDMI cable or HDMI-DVI cable. · Connects to another product using a HDMI cable. Connects to a PC using a DP cable.
Connects to another product using a HDMI cable.
Connect to a USB memory device or TOUCH OUT cable. ” The USB ports on the product accept a maximum constant current of
0.5A. If the maximum value is exceeded, USB ports may not work.
Outputs sound to an audio device via an audio cable.
Connects to an external IR cable that receives signals from the remote control.
Connects to MDC using an RS232C adapter.
Connect to a USB port on the product to use the touch function.
Connect to a USB port on a PC to use the touch function.

10

QM43R-T/QM55R-T
” The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Port
USB 1 ¨(1.0A)

RJ45
RS232C IN DVI/MAGICINFO IN HDMI IN 1 (ARC) HDMI IN 2 (DAISY CHAIN IN) DP IN (DAISY CHAIN IN) HDMI OUT (DAISY CHAIN OUT)
USB 2(0.5A)
DVI/HDMI AUDIO IN AUDIO OUT IR IN RS232C OUT TOUCH OUT SCREEN TOUCH OUT PC

Description
Connect to a USB memory device or TOUCH OUT cable. ” The USB ports on the product accept a maximum constant current of 1.0A.
If the maximum value is exceeded, USB ports may not work.
Connects to MDC and the Internet using a LAN cable. (10/100 Mbps) ” Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair.
Connects to MDC using an RS232C adapter.
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable. MAGICINFO IN: Connects to a network box using DP-DVI cable to use Magicinfo.
Connects to a source device using a HDMI cable or HDMI-DVI cable.
· Connects to a source device using a HDMI cable or HDMI-DVI cable. · Connects to another product using a HDMI cable. Connects to a PC using a DP cable.
Connects to another product using a HDMI cable.
Connect to a USB memory device or TOUCH OUT cable. ” The USB ports on the product accept a maximum constant current of
0.5A. If the maximum value is exceeded, USB ports may not work.
Receives sound from a source device via an audio cable.
Outputs sound to an audio device via an audio cable.
Connects to an external IR cable that receives signals from the remote control.
Connects to MDC using an RS232C adapter.
Connect to a USB port on the product to use the touch function.
Connect to a USB port on a PC to use the touch function.

11

Control menu
” The power button(«) is located on the bottom of the product. ” If you press the power button on the product when the product is
turned on, the control menu will be displayed.

Power off
Press: Move

Source Press & Hold: Select

Items

Description

Power off

Power off the product.
· With the control menu screen displayed, briefly press the power button to move the cursor to Power off, and then press and hold the power button to turn off the product.

Select the connected input source.

Source

· With the control menu screen displayed, briefly press the power button to move the cursor to Source, and then press and hold the power button to display the input source screen.
· With the input source screen displayed, press and hold the power button to switch to the desired input source.

” The power button can only be used for Power off and Source. ” To exit from the control menu screen, wait for 3 seconds or more without pressing the power button.

12

Administrator menu (Supported models: QMR-T)
” Touching and holding on the screen when the product is turned on displays the administrator menu.
” If the touchscreen control is not available, use the remote control to go to System Touch Control Touch Control and select On from the OSD menu.
” If the administrator menu is not displayed, use the remote control to go to System Touch Control Admin Menu Lock and select Off from the OSD menu.
” This menu is not displayed, when using touch mode on a connected PC.

Buttons
Volume Home Menu
Source Power

Description
Adjust the Volume. · Select Volume from the administrator menu. Enter Home screen. · Select Home from the administrator menu.
Display the OSD menu. To change settings, select a menu item. · Select Menu from the administrator menu.
Select the connected input source. Select an input source from the displayed list of input sources. · Select Source from the administrator menu.
Power off the product. · Select Power from the administrator menu.

Volume

Home

Menu

Source

Power

13

Precautions when handling the panel
” The colour and the appearance may differ depending on the model. Do not stand the product as shown in the image. The panel is fragile and can get damaged.
Lay the product down to handle it as shown in the image. (the packaging can be used). ” Supported models: 85 inches or more
Ensure you use the handles on the back when moving the product. ” Supported models: 85 inches or more
Do not hold or grasp any area of the product within 15 mm from the front.
15 mm
14

Before Installing the Product (Installation Guide)
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. · Ensure that an authorised installation company installs the wall mount. · Otherwise, it may fall and cause personal injury. · Make sure to install the specified wall mount.
Tilting Angle and Rotation
” Contact Samsung Customer Service Centre for further details. · The product can be tilted at a maximum angle of 15° from a perpendicular wall surface. · To use the product in Portrait mode, rotate clockwise until the power indicator (A or B) is
positioned as shown in the images below.
15°
A

A

B

B

” Do not use this model installed on a ceiling, floor, or table.

Ventilation
” Contact Samsung Customer Service Centre for further details.
Installation on a Perpendicular Wall
A Minimum 40 mm B Ambient temperature: Under 35 °C ” When installing the product on a perpendicular wall, allow at least
40 mm of space between the product and wall surface for ventilation and ensure that the ambient temperature is kept below 35 °C.
A

Installation on an Indented Wall
A Minimum 40 mm B Minimum 70 mm C Minimum 50 mm D Minimum 50 mm E Ambient temperature: Under 35 °C ” When installing the product on an indented
wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 °C.

B

B

B

D A
D

C

C

E

15

Installing the Wall Mount
A

Preparing before installing Wall-Mount
To install a wall-mount from another manufacturer, use the Holder-Ring. ” For the QM32R-T, QB85R, QM85R and 82-inch models that it does not provide Holder-Ring(A).
Installing the Wall Mount
· The wall mount kit (sold separately) allows you to mount the product on the wall. · The provided image is only for reference. For detailed information on installing the wall mount, see instructions
provided with the wall mount. · We recommend you contact a technician for assistance when installing the wall mount bracket. · Samsung is not responsible for any damage to the product or injury to yourself or others if you select to install
the wall mount on your own.

16

Wall Mount Kit Specifications (VESA)
” Install your wall mount on a solid wall perpendicular to the floor. To install the product on the other wall area, contact the nearest agency. If you install the product on a slanted wall, it may fall and result in severe personal injury.

· Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
· Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.
· For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.
· Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
· Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
· Do not mount the product at more than a 15 degree tilt.
· Always have at least two people mount the product on a wall. (Four or more people for the 82-inch size and larger models.)
· Standard dimensions for wall mount kits are shown in the table below.

Model Name

VESA screw hole specs (A * B) in millimetres

Standard Screw

Quantity

QB43R / QB49R / QB50R / QB55R / QM32R / QM43R / QM49R / QM50R / QM55R / QM32R-T / QM43R-T / QM55R-T

200 × 200

QB65R / QB75R / QM65R / QM75R

400 × 400

M8

4

QB85R / QM85R / QE82R

600 × 400

QB98R

900 × 600

” Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.

17

Chapter 02
Using a touchscreen monitor (Supported models: QMR-T)

Touchscreen monitor

Connecting the touch overlay

Control a PC by tapping the screen instead of using an input device such as a keyboard or mouse. The touch screen functions by detecting a minute electric current that runs through your body (capacitive). Make sure to use the surface of your finger tip when tapping the screen.
Read below before using the product
· Take extra care to ensure an electrical substance does not contact the screen. The screen may not function properly if there is static.
· Do not press hard on the touchscreen with your finger tip. Do not use a sharp object when tapping the screen. The screen may break or get damaged.
· Do not tap the screen while wearing a glove, with a dirty finger, or using something sharp such as your fingernail or a ballpoint pen. The screen may not function properly.
· Take extra care to ensure the screen does not contact moisture. The touch sensor may not function properly.
· Displaying a still image on the screen for an extended period of time may cause after images (screen degradation) or stains. Switch off the screen when not in use.

” Touch functions are not supported in applications other than the OSD menu and administrator menu.
Connect the TOUCH OUT cable between TOUCH OUT SCREEN and USB 1 ¨(1.0A) or USB 2(0.5A) port on the product.

TOUCH OUT SCREEN

USB 1 (1.0A), USB 2(0.5A)

18

Connecting the touchscreen monitor
” Connecting parts may differ in different products.
Connecting to a PC
1 Connect your PC to the product using a HDMI or HDMI-DVI cable.
Connecting the devices using a HDMI cable
HDMI IN
Connecting the devices using a HDMI-DVI cable
HDMI IN

2 Connect the power cable from the product to the power outlet. 3 After the power supply is connected, the product automatically detects and switches to the
connected input source. ” If the screen appears blank, turn the product off and then on again.
4 Connect the TOUCH OUT PC port on the product to a USB port on the PC using the TOUCH
OUT cable.
TOUCH OUT PC
Connecting to a laptop or tablet PC
A laptop or tablet PC can be connected to the product using the same method when connecting a desktop PC. ” If touchscreen control is not available after the devices are connected
­ Make sure to connect the HDMI or HDMI-DVI cable before connecting the TOUCH OUT cable.
­ If touchscreen control is still unavailable after the cables are connected properly, disconnect the TOUCH OUT cable and then connect it again.

19

Configuring the touchscreen monitor settings

To properly use the touch function of the product in Windows, go to Tablet PC Settings and calibrate the product. ” First connect the touchscreen monitor before configuring the following settings. ” The maximum number of touchscreen monitors that can be connected simultaneously varies, depending on the operating system and graphics card settings. ” If Tablet PC Settings is not found in Control Panel, search for Tablet PC Settings from Search Control Panel. ” If used in a multi-screen setup, make sure you have configured QMR-T as the main display.

Calibration
” Instructions below are for Windows 8. The same method applies to both Windows 7, Windows 8 and Windows 10.
” After changing the Picture Size from the OSD menu, you may need to calibrate the picture settings again.
” Upon occurrence of an error during calibration, go to Tablet PC Settings. In the Display tab, tap Reset and calibrate again.
1 In the Display tab, select Setup under Configure.

2 Tap the page displayed on the product with your finger.
” In dual monitor mode: If the following page does not appear on the product, press the Enter key to display the page.
Touch this screen to identity it as the touchscreen.

If this is not the Tablet PC screen, press Enter to move to the next screen. To close the tool, press Esc.

20

3 Select the product from Display under Display options. Next, select Calibrate.

5 After calibration is complete, the message Do you want to save the calibration data?
appears. Select Yes.
Digitizer Calibration Tool
Do you want to save the calibration data?

Yes

No

6 The touchscreen monitor has been calibrated successfully.
” Selecting Reset will remove the calibration data.

4 Perform calibration following the onscreen instructions displayed as shown in the image.

To provide calibration samples, tap the crosshair each time that it appears on the screen. Right-click anywhere on the screen to return to the last calibration point. Press the Esc button to close the tool. Do not change your screen orientation until you have completed the calibration process.

21

Chapter 03
Specifications

General

Model Name
Panel

Size Display area

Model Name
Panel

Size Display area

Model Name
Panel

Size Display area

QM32R / QM32R-T
32 CLASS (31.5 inches / 80.1 cm) 698.4 mm (H) x 392.85 mm (V)

QB43R / QM43R / QM43R-T
43 CLASS (42.5 inches / 107.9 cm) 941.184 mm (H) x 529.416 mm (V)

QB49R / QM49R
49 CLASS (48.5 inches / 123.2 cm) 1073.78 mm (H) x 604.0 mm (V)

QB50R / QM50R
50 CLASS (49.5 inches / 125.7 cm) 1095.84 mm (H) x 616.41 mm (V)

QB55R / QM55R / QM55R-T
55 CLASS (54.6 inches / 138.7 cm) 1209.6 mm (H) x 680.4 mm (V)

QB65R / QM65R
65 CLASS (64.5 inches / 163.9 cm) 1428.48 mm (H) x 803.52 mm (V)

QB75R / QM75R
75 CLASS (74.5 inches / 189.3 cm) 1650.24 mm (H) x 928.26 mm (V)

QB85R / QM85R
85 CLASS (84.5 inches / 214.7 cm) 1872.0 mm (H) x 1053.0 mm (V)

QB98R
98 CLASS (97.5 inches / 247.7 cm) 2158.848 mm (H) x 1214.352 mm (V)

QE82R
82 CLASS (81.5 inches / 207.1 cm) 1805.76 mm (H) x 1015.74 mm (V)

22

Model Name

Resolution Power Supply

Optimum resolution
Maximum resolution

Environmental considerations

Operating Storage

QM32R / QM32R-T

QB43R / QB49R / QB50R / QB55R / QB65R / QB75R / QE82R / QB85R

QB98R / QM43R / QM49R / QM50R / QM55R / QM65R / QM75R / QM43R-T /
QM55R-T / QM85R

3840 x 2160 @ 60 Hz (HDMI) 3840 x 2160 @ 60 Hz (DisplayPort)

1920 x 1080 @ 60 Hz (DVI) 3840 x 2160 @ 60 Hz (HDMI)

1920 x 1080 @ 60 Hz (DVI) 3840 x 2160 @ 60 Hz (HDMI) 3840 x 2160 @ 60 Hz (DisplayPort)

AC100-240V~ 50/60Hz Refer to the label at the back of the product as the standard voltage can vary in different countries.
Temperature: 0 °C ­ 40 °C (32 °F ­ 104 °F) * For installing the enclosure, keep the internal temperature at 40 °C or below. Humidity: 10% ­ 80%, non-condensing
Temperature: -20 °C ­ 45 °C (-4 °F ­ 113 °F) Humidity: 5% ­ 95%, non-condensing * Applicable before the product package is unpacked.

23

· Plug-and-Play This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimises the monitor settings. Monitor installation takes place automatically. However, you can customise the installation settings if desired.
· Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product performance. · This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution
may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product. · For detailed device specifications, visit the Samsung website. · (Europe only)
To access the EPREL registration of the model: QB43R ~ QB65R / QM43R ~ QM65R / QM43R-T ~ QM55R-T (1) Go to https://eprel.ec.europa.eu (2) Get the model identifier from the energy label of the product and type it in the search box (3)Energy Labelling information of the model is shown * You can directly access the product information via https://eprel.ec.europa.eu/qr/##### (registration no.)
The registration no. can be found on the rating label on your product. · (Turkey only)
To access the energy labelling information of the model:QB43R ~ QB65R / QM43R ~ QM65R / QM43R-T ~ QM55R-T (1) Go to https://www.samsung.com/global/ecodesign_energy (2) Get the model identifier from the energy label of the product and type it in the search box (3)Energy labelling information can be found
24

Preset Timing Modes

The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank with the power indicator on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
” DVI port is not supported on the QM32R, QM32R-T models.

Resolution
IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA CVT, 3840 x 2160RB VESA CVT, 3840 x 2160RB VESA DMT, 640 x 480 VESA DMT, 640 x 480 VESA DMT, 640 x 480 VESA DMT, 800 x 600 VESA DMT, 800 x 600 VESA DMT, 800 x 600 VESA DMT, 1024 x 768 VESA DMT, 1024 x 768 VESA DMT, 1024 x 768 VESA DMT, 1152 x 864 VESA DMT, 1280 x 720 VESA DMT, 1280 x 800 VESA DMT, 1280 x 1024 VESA DMT, 1280 x 1024 VESA DMT, 1366 x 768

Horizontal Frequency
(kHz) 31.469 35.000 49.726 68.681 110.500 133.313 31.469 37.861 37.500 37.879 48.077 46.875 48.363 56.476 60.023 67.500 45.000 49.702 63.981 79.976 47.712

Vertical Frequency
(Hz) 70.087 66.667 74.551 75.062 49.977 59.997 59.940 72.809 75.000 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 59.810 60.020 75.025 59.790

Pixel Clock Sync Polarity

(MHz)

(H/V)

DP IN

28.322

-/+

O

30.240

-/-

O

57.284

-/-

O

100.000

-/-

O

442.000

+/-

O

533.250

+/-

O

25.175

-/-

O

31.500

-/-

O

31.500

-/-

O

40.000

+/+

O

50.000

+/+

O

49.500

+/+

O

65.000

-/-

O

75.000

-/-

O

78.750

+/+

O

108.000

+/+

O

74.250

+/+

O

83.500

-/+

O

108.000

+/+

O

135.000

+/+

O

85.500

+/+

O

Port

DVI IN HDMI IN

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

Resolution
VESA DMT, 1440 x 900 VESA DMT, 1600 x 900RB VESA DMT, 1680 x 1050 VESA DMT, 1920 x 1080
VESA DMT, 2560 x 1440RB
CTA-861, 720(1440) x 576i CTA-861, 720(1440) x 480i CTA-861, 720 x 576 CTA-861, 720 x 480 CTA-861, 1280 x 720 CTA-861, 1280 x 720 CTA-861, 1920 x 1080i CTA-861, 1920 x 1080i CTA-861, 1920 x 1080 CTA-861, 1920 x 1080 CTA-861, 1920 x 1080 CTA-861, 1920 x 1080 CTA-861, 1920 x 1080 CTA-861, 3840 x 2160 CTA-861, 3840 x 2160 CTA-861, 3840 x 2160 CTA-861, 3840 x 2160 CTA-861, 3840 x 2160 CTA-861, 4096 x 2160 CTA-861, 4096 x 2160 CTA-861, 4096 x 2160 CTA-861, 4096 x 2160

Horizontal Frequency
(kHz) 55.935 60.000 65.290 67.500
88.787
15.625
15.734
31.250 31.469 37.500 45.000 28.125 33.750 27.000 28.125 33.750 56.250 67.500 54.000 56.250 67.500 112.500 135.000 54.000 67.500 112.500 135.000

Vertical Frequency
(Hz) 59.887 60.000 59.954 60.000
59.951
50.000
59.940
50.000 59.940 50.000 60.000 50.000 60.000 24.000 25.000 30.000 50.000 60.000 24.000 25.000 30.000 50.000 60.000 24.000 30.000 50.000 60.000

Pixel Clock Sync Polarity

(MHz)

(H/V)

DP IN

106.500

-/+

O

108.000

+/+

O

146.250

-/+

O

148.500

+/+

O

Port

DVI IN HDMI IN

O

O

O

O

O

O

O

O

241.500

+/-

O

O

27.000

-/-

O

O

27.000

-/-

O

O

27.000

-/-

27.000

-/-

74.250

+/+

74.250

+/+

74.250

+/+

74.250

+/+

74.250

+/+

74.250

+/+

74.250

+/+

148.500

+/+

148.500

+/+

297.000

+/+

297.000

+/+

297.000

+/+

594.000

+/+

594.000

+/+

297.000

+/+

297.000

+/+

594.000

+/+

594.000

+/+

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

25

Chapter 04
Appendix

Licence
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Open Source Licence Notice In the case of using open source software, Open Source Licences are available on the product menu. Open Source Licence Notice is written only English. For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send email to [email protected]

THIS PRODUCT IS SOLD WITH A LIMITED LICENCE AND IS AUTHORISED TO BE USED ONLY IN CONNECTION WITH HEVC CONTENT THAT MEETS EACH OF THE THREE FOLLOWING QUALIFICATIONS: (1) HEVC CONTENT ONLY FOR PERSONAL USE; (2) HEVC CONTENT THAT IS NOT OFFERED FOR SALE; AND (3) HEVC CONTENT THAT IS CREATED BY THE OWNER OF THE PRODUCT.
THIS PRODUCT MAY NOT BE USED IN CONNECTION WITH HEVC ENCODED CONTENT CREATED BY A THIRD PARTY, WHICH THE USER HAS ORDERED OR PURCHASED FROM A THIRD PARTY, UNLESS THE USER IS SEPARATELY GRANTED RIGHTS TO USE THE PRODUCT WITH SUCH CONTENT BY A LICENSED SELLER OF THE CONTENT.
YOUR USE OF THIS PRODUCT IN CONNECTION WITH HEVC ENCODED CONTENT IS DEEMED ACCEPTANCE OF THE LIMITED AUTHORITY TO USE AS NOTED ABOVE.

26

Documents / Resources

SAMSUNG QM32R-B 32 Inch LED-backlit LCD Display [pdf] User Manual
QMR-B Series, QM32R-B, 32 Inch LED-backlit LCD Display, QM32R-B 32 Inch LED-backlit LCD Display

Leave a comment

Your email address will not be published.