Philips Global Consumer Care - Royal Philips Electronics
Philips Customer Service Support - Home | Philips
User Manual for PHILIPS models including: D260, D265, Cordless DECT Landline Phone, DECT Landline Phone, Landline Phone, Cordless Phone, D260, Phone
Visit the support page for your Philips Cordless phone with answering machine D2651B/01
Visit the support page for your Philips Cordless phone D2601B/01
File Info : application/pdf, 2 Pages, 3.26MB
DocumentDocumentD260 D265 Warning · The Electrical network is classified as hazardous. The only way to power down the charger is to unplug the power supply from the electrical outlet. Ensure that the electrical outlet is always easily accessible. · Refer to safety information before using the product. · Hereby, TP Vision Europe B.V. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. · Use only the power supply listed in the user instructions. · Use only the batteries listed in the user instructions. · Do not allow the product to come into contact with liquids. · Risk of explosion if battery is replaced by an incorrect type. · Dispose of used batteries according to the instructions. · When the handset rings or when the handsfree is activated, keep the handset away from your ear to avoid hearing damage. D265 D260 D265 D260 D265 D265 D265 D260 3 Get started Insert batteries 1 a welcome message (country dependent). 2 Set the country and language if prompted. 3 Set the date and time. · If the time is in 12-hour format, press / to select [am] or [pm] (country dependent). Charge your phone > 70% 40% - 70% Flashing: low battery Scrolling: charging in progress Charge 8 hours 10% - 40% < 10% www.philips.com/suppor t To access the user instructions online, use the reference model number written on the product label at the bottom of the base station. MMD Hong Kong Holding Limited Kong Holding Limited MMD Hong MMD Hong Kong Holding Limited UMS_D260/265 EN_V1.0 4 Enjoy Phonebook Add record 1 Press . 2 Select [Phonebook] > [Add new]. 3 Follow on-screen instructions. Call from the phonebook 1 Press . 2 Select a record and press . Direct access memory You have 2 direct access memories (keys 1 and 2).To dial the saved phone number automatically, press and hold on the keys in standby mode. Depending on your country, keys 1 and 2 are preset to the voice mail number and information service number of your service provider respectively. (network dependent). Call log Call from the call log 1 Press . 2 Select a record and press . View record Press > > [View]. Save record 1 Press > > [Save number]. 2 Follow on-screen instructions. Delete record 1 Press > > [Delete]. 2 Follow on-screen instructions. Redial list Call from the redial list 1 Press . 2 Select a record and press . Save record 1 Press > > [Save number]. 2 Follow on-screen instructions. Delete record 1 Press > > [Delete]. 2 Follow on-screen instructions. Telephone answering machine (for D265 only) Record an announcement 1 Press > [Answ machine] > [Announcement]. 2 Follow on-screen instructions. Listen to the incoming messages Press > [Answ machine] > [Play]. Delete an incoming messages 1 When you listen to the message, press to enter the options menu. 2 Select [Delete], then press Register additional handsets You can register additional handsets to the base station. 1 Press . 2 Select [Services] > [Register], then press 3 Press and hold on the base station for 5 seconds. 4 Enter the system PIN/passcode (0000). 5 Press @ Registration is complete in less than 2 minutes. Restore default settings You can reset your phone settings to the original factory settings. 1 Press . 2 Select [Services] > [Reset], then press to 3 Follow on-screen instructions. Note · You may recall the original PIN/passcode by following this procedure. Technical data Battery · Philips: 2 x AAA NiMH 1.2 V Rechargeable 550 mAh batteries Use only the supplied batteries. Adapter Base and charger: Input: Ouput: Meic: MN0063-E060040 HuaJin: HJ-0600400P1-EU Phonebook with 50 entries Call log with 20 entries Talk time: 16 hours Standby time: 180 hours Note · prevent noise and caller ID problems caused by the DSL interference. · www.p4c.philips.com. Frequently asked questions No signal bar is displayed on the screen. · The handset is out of range. Move it closer to the base station. · If the handset displays [Unregistered], register your handset (see the section on "Register additional handsets"). If I fail to pair (register) the additional handsets to the base station, what do I do? Your base memory is full. Access > [Services] > [Unregister] to unregister the unused handsets and try again. I have chosen a wrong language which I cannot read, what do I do? 1 Press to go back to the standby screen. 2 Press to access the main menu screen. 3 The following options will appear on the screen: [Phone setup] > [Language] [Réglages] > [Langue] > [Sprache] > [Lingua] 4 Select them to access the language options. 5 Select your own language. My handset is in searching status, what do I do? · Make sure that the base station has power supply. · Register the handset to the base station. · Move the handset closer to the base station. I cannot change the settings of my voice mail, what do I do? The voice mail service is managed by your service provider but not the phone itself. Contact your service provider to change the settings. No display · Make sure the batteries are charged. · Make sure there are power and phone connections. The handset on the charger does not charge. · Make sure the batteries are inserted correctly. · Make sure the handset is placed properly on the charger.The battery icon animates when charging. · Make sure the docking tone setting is turned on. When the handset is placed correctly on the charger, you can hear a docking tone. · The charging contacts are dirty. Disconnect the power · Batteries are defective. Purchase new ones with the Bad audio (crackles, echo, etc.) · The handset is nearly out of range. Move it closer to the base station. · The phone receives interference from the nearby electrical appliances. Move the base station away from them. · The phone is at a location with thick walls. Move the base away from them. The handset does not ring. Make sure the handset ringtone is turned on. The caller ID does not display. · The service is not activated. Check with your service provider. · The caller's information is withheld or unavailable.