User Manual for better bathrooms models including: BeBa-27962 Sahara Towel Radiator, Sahara Towel Radiator, Towel Radiator, Radiator
BeBa_27962, BeBa_27963, BeBa_27964, BeBa_27965, BeBa_27966, BeBa_27967, BeBa_27968, BeBa_27969 BeBa_27970 Sahara Towel Radiator Please note: Image is for illustrative purposes only and may differ slightly to the actual product Multi-person assembly Tools required We always recommend using professional tradespeople to install your product V1_10.11.20 Product Code BeBa_27962 BeBa_27963 BeBa_27964 BeBa_27965 BeBa_27966 BeBa_27967 BeBa_27968 BeBa_27969 BeBa_27970 BTU 993 904 914 1102 1697 1392 1199 1880 1508 Wattage 291 265 268 323 497 408 351 551 442 Parts A. 1 x Radiator B. 1 x Air Vent (Bleed Valve) C. 1 x Blanking Cap D. 4 x Wall plug E. 4 x Wall Bracket F. 4 x Washer G. 4 x Wall screw H. 4 x Rail Bracket I. 4 x Bracket Screw J. 4 x Connecting Screw Please note that Parts are for illustrative purposes only and may differ slightly to the actual product Tools required Spanner Flathead screwdriver Philips screwdriver Tape measure Drill and 8mm drill bit Spirit Level Pencil Sealing tape 3 Installation Please note: Before starting any installation, turn off the water supply. Please note: Before commencing any installation, the desired location should be checked before drilling, that no pipes or wires can be damaged. First, prepare the water supply pipes to match up with the towel radiator and valve dimensions being used. Fit the radiator valve tail and nut into the towel rail (not supplied) (at both sides) and using sealing tape, tighten into position, then follow the installation below. 1. Fit the blanking cap and air vent in the top of the rail, (add a little sealer tape to secure) and tighten using the spanner, be sure not to overtighten. 2. The rear of the towel rail has four location holes to fix the brackets. Measure the distance between all the location holes and mark these on the wall in the required location, use a spirit level to ensure these are horizontally and vertically aligned. 4 3. Using the drill and 8mm drill bit, drill into the marked positions then insert the wall plugs and tap flush to the finished wall surface. Please note: If drilling into a tile, it is recommended to tape the wall to prevent the drill from slipping. 4. Position the wall brackets and screw into place using the screws provided (securing each with a washer) with the Philips screwdriver. 5. Next, proceed to fix the rail brackets to the rear of the radiator and screw into place using the screws provided with the Philips screwdriver. 5 6. Align and push the rail brackets on the radiator onto the wall brackets secured to the wall. Secure the two together with the connecting screws provided (insert through the slot in the bracket) and tighten using the Philips screwdriver, be sure not to overtighten. Please note: You may need two people to connect the radiator, depending on the model purchased. 7. Finally, fit the radiator valves to the pipework and connect to the radiator valve tail and tighten all connections. IMPORTANT! The product is supplied un-filled. The rail should be filled with a water (80%) and glycol (20%) mixture if NOT being connected to the central heating system, also allow 5% air gap. After installation After the above installation, turn on the water supply and using the flathead screwdriver, open the air vent via the central screw, open the inlet valve and let the water rush into the radiator. Check all connections for leaks. Once water overflows from the air vent, this means that there will be no air bubbles present. Use a screwdriver to close the air vent and then the radiator is ready to use. Cleaning This radiator is made from steel with a painted finish. To maintain the surface of your product (especially when subjected to steam or splashes), wipe with a clean damp cloth and wipe dry. Do not use abrasive cleaning agents or materials which can strip and scratch the surface; the use of these agents or materials can invalidate your guarantee. It is recommended to wipe and dry on a regular basis. 7pdf-lib (https://github.com/Hopding/pdf-lib) WPS 文字