Пульт дистанционного управления Keilton Basic RM51 для датчика положения фар
Описание
The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.
Функции
- Низкое энергопотребление.
- Infrared communication.
- Setting most of the Keilton Sensors G2.
- Custom Configurations can be saved to A, B, C, D, or For.
- 40′ maximum IR range.
- RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)
Технические характеристики
Информация о заказе
| Модель | Описание |
| РМ51.А0 | Basic Sensor Controller RM51 |
| РМ51.А1 | Basic Sensor Controller RM51 With RML |
Информация о заказе – Аксессуары
| Модель | Описание |
| РМЛ | Extended IR range for commissioning |
Размеры
Этикетка продукта
Удаленные инструкции
Режим памяти (ввод в эксплуатацию)
To begin commissioning, follow these steps:
- Выберите профессионала в области памятиfile: A, B, C, D или E.
- The remote’s indicator lights will flash, indicating the currently saved settings.
- Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
- Point the remote at the desired luminaire and press “SEND.”
- The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
- If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.
E Mode allows for visual adjustment to choose the desired dimming level.
Сбор дневного света (режим F)
Continuous Adjustment Mode adjusts dimming levels based on daylight.
- Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
- Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
- Review the selected settings and make changes as necessary. Press “SEND.”
- If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.
Дополнительные удаленные функции
| ON | Повороты ON светильники. |
| ВЫКЛЮЧЕННЫЙ | Повороты ВЫКЛЮЧЕННЫЙ светильники. |
|
ТЕСТ |
The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100%, Чувствительность: ВЫСОКАЯ, Время выдержки: 2s, Standby dim: 50%, Время работы в режиме ожидания: 2с. |
| ПЕРЕЗАГРУЗИТЬ | Trim= 100%, Sensitivity = Высокий, T1 = 5 мин., Standby Dim = 30%, T2 = 60 мин.,
Photocell = ВЫКЛЮЧЕННЫЙ. |
| ДИМ+/- | Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous
затемнение |
| УРОВЕНЬ ОТДЕЛКИ | Set the Maximum brightness. |
| ЧУВСТВИТЕЛЬНОСТЬ | Set the motion sensitivity of the sensor НИЗКИЙ:50% / ВЫСОКИЙ:100%,
OFF: disable the motion detection function. |
| ВРЕМЯ УДЕРЖАНИЯ | Длительность периода без обнаружения присутствия человека перед переходом в режим ожидания. |
| РЕЖИМ РЕЖИМА | Select any standby dim level. |
| STANDBY ВРЕМЯ | Standby time, when the time is set to “∞”, the daylight detection function is activated. |
| ФОТОЭЛЕМЕНТ | visible light threshold, the fixture is allowed to be turned on when it falls below the threshold
НИЗКИЙ:5fc / ВЫСОКИЙ:20fc, КАЛ: Collect the current visible light illuminance as the threshold, OFF: disable PHOTOCELL function. |
| РЕЖИМ | Default configuration parameters for modes A к F. |
| ОТПРАВЛЯТЬ | Отправьте настройки на датчик. |
| ПО УМОЛЧАНИЮ РЕЖИМ А | Trim= 100%, Sensitivity = Низкий, T1 = 30 мин., Standby Dim = 50%, T2 = ∞, Photocell = КАЛ. |
| РЕЖИМ ПО УМОЛЧАНИЮ B | Trim= 100%, Sensitivity = Низкий, T1 = 30 мин., Standby Dim = 50%, T2 = 15 мин., Photocell = КАЛ. |
| РЕЖИМ ПО УМОЛЧАНИЮ C | Trim= 100%, Sensitivity = Низкий, T1 = 30 мин., Standby Dim = 50%, T2 = 15 мин., Photocell = ВЫКЛЮЧЕННЫЙ. |
| РЕЖИМ ПО УМОЛЧАНИЮ D | Trim= 50%, Sensitivity = Низкий, T1 = 30 сек., Standby Dim = 50%, T2 = 30 мин., Photocell = КАЛ. |
| РЕЖИМ ПО УМОЛЧАНИЮ E | Manual Dimmer Mode, Trim 100%. |
| РЕЖИМ ПО УМОЛЧАНИЮ F | Daylight Harvesting, Trim= 50%, Sensitivity = Низкий, T1 = 15 мин.. |
Связаться с нами
- 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
- Т: +1 443-320-2233 (M-F 9 am-5 pm ET)
- E: support@autani.com
FAQ
How do I change the memory profile настройки?
Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save
Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?
No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.
What is the expected operation if the user sets Standby Time to something other than INFINITE?
moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.
If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?
The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.
Документы/Ресурсы
 |
Пульт дистанционного управления Keilton Basic RM51 для датчика положения фар [pdf] Руководство пользователя RM51.A0, RM51.A1, RM51 Пульт дистанционного управления для датчика крепления, RM51, Пульт дистанционного управления для датчика крепления, для датчика крепления, Датчик крепления |