Руководство пользователя GPS-насадки HARVEST TEC 880GPS

880GPS GPS Attachment

Инструкция по применению
Model 880GPS
GPS Attachement

880GPS 6/22

1

Harvest Tec 880GPS Table of Contents
Введение оконченоview Installation of GPS Receiver & Harness
Installation of GPS Receiver Installation of GPS Harness Setup Instructions Operating Instructions Converting Yield Date File PC Installation of Yield File Converter Program Converting Yield Data File Troubleshooting Parts Breakdown for Model 880 GPS Pin Outs Warranty

СТР
3 3 3 3 3 4 4 5 5 6 6 7 7 8

2

Introduction Congratulations on purchasing a Harvest Tec Model 880 GPS attachment. The GPS harness will allow you attach a Garmin 16xHVS receiver to Harvest Tec’s 600 moisture monitoring system or the 665 preservative applicator system. This will allow you to collect important baling information to create yield files for each individual job. The model 880GPS includes the Garmin 16xHVS receiver to connect to your Harvest Tec system, and Harvest Tec’s yield mapping file converter program.
надview The Harvest Tec model 880GPS gathers WAAS information on the fly and sends it to the main processor. With this information the system creates a yield mapping file that will be stored within the processor on 600/665 systems. This yield file, after being converted by Harvest Tec’s yield mapping conversion program, can be useful to the user for present and future field management. The yield file is capable of being loaded into any type of field management software. The yield file created will indicate where each bale was tied off. If you have Harvest Tec’s Bale Identification System you will then have the ability to write that coordinate to the Tag and this will give you not only proof of what field the bale came from but also the approximate location of where the bale was made.
Installation of GPS Receiver & Harness Installation of GPS Receiver
Locate the Garmin 16xHVS receiver. The GPS receiver will be mounted on top of your baler in front of the misstie flag indicators or if they’re not present on a flat surface near the knotter cover/door. This location should give the GPS receiver the best available location. Installation of GPS Harness Connect the plug end of the harness from the Garmin receiver into the Optional Port on the Dual Channel Processor (DCP) on the baler. Secure harness to baler with supplied cable ties, making sure wiring harness is not in any pinch points and will not come in contact with moving parts on the baler.
3

Setup Instructions 1. Turn the control system on. After a few seconds the Main Menu screen should appear. Press Setup Mode, the Setup Mode screen will then appear. 2. Press Yield Mapping setup. a. Yield Mapping Setup will now be displayed.
3
4 2
3. Press the underlined value next to Swath Width (Ft). Enter in the swath width that will be baled, press Enter to confirm.
4. Enter the underlined value next to GPS. Enabling the GPS will require entering the appropriate value. Press 0 to Disable, 2 to Enable the Garmin GPS. Press Enter to confirm.
Operation Instructions 1. Once installation and setup is complete the system is ready for baling. There is a GPS indicator icon that will appear in either of the Automatic or Manual mode screens. The GPS icon shows the user that the GPS is transmitting data to the DCP to be processed. The GPS icon, if getting a good satellite signal, will continually increase/decrease in size. While all this is going on a Yield file is being created and saved to the DCP.
ЗНАЧОК GPS
2. Once baling is complete, create a New Job and the yield data file that was written to the DCP yield file will be complete and ready to be converted. See CONVERTING YIELD DATA FILE для следующего шага.
*NOTE: If you’re a first time user, begin with the INSTALLATION OF YIELD DATA FILE CONVERTER PROGRAM before attempting to convert the yield data file. *There is no indication the system is connected to a GPS when using and ISO monitor or an iPad.
4

Converting Yield Data File PC Installation of Yield Data File Программа конвертера
1. Plug the USB flash provided in the 880 kit into the USB port on the computer. 2. The USB flash will have a zipped file on it and will be labeled ydConverterSetup-V1_0_0_0.
a. Double click on that folder to open it and there will be two files inside labeled setup & ydConverterSetup. Double click on ydConverterSetup.
3. A setup screen will appear, click Next. 4. The next screen will ask you what folder you would like to save the File Converter Program in. Use
the default option and click Next to accept. Next a confirmation screen will appear, press Next to confirm. The computer will then let the Yield File Converter Program install itself (Computer will take up to a 1 min to save the yield file converter program to its desktop).
5. Once the program has been installed you will see this Icon on the computers desktop as pictured above. 5

Converting Yield Data File
1. The yield data file that was created on the USB flash while baling will need to be converted before it can be utilized in a yield mapping program. Start by double clicking on the yield mapping file converter Icon located on the computers desktop.
2. The program should open. Click on Select Files and navigate to the USB flash where the data files are located. Selected the file labeled as the users created job name .YDT

3. Once the .YDT file has been selected, click open to start the conversion. This process will take up to a few seconds. The converted file will read; the users created job name ­ym. It will be located on the USB flash that the yield data file был создан на.
NOTE: Once converted, the file is in the appropriate format and it can be used by any yield mapping software/program.

Решение Проблем

ПРОБЛЕМА

ВОЗМОЖНАЯ ПРИЧИНА

РЕШЕНИЕ

GPS icon not displaying in Auto or Manual modes
Yield Map not showing up on DCP job records

1. GPS disabled.
2. Harness is damaged or the connection is dirty/damaged.
*There is no indication of connection on an iPad or ISO Monitor. 1. GPS is disabled.
2. GPS did not connect to GPS satellites prior to baling.
3. Harness is damaged or the connection is dirty/damaged.

1. Check Yield Mapping Setup to make sure that the GPS is enabled. 2. Inspect GPS wiring harness and connections.
1. Check Yield Mapping Setup to make sure that the GPS is enabled. 2. Verify that the GPS icon is beign displayed in Automatic/Manual modes 3. Inspect GPS wiring harness and connections.

6

Parts Breakdown for Model 880GPS
1

2 3

№ Описание

Часть#

Кол-во

1 GPS-приемник

006-6650GPS 1

2 GPS Receiver Mount 001-2012GPS 1

3 USB Converter File 006-5650USB 1

Закрепить

Разъем звездообразного колеса и датчика скорости тюка на DCP

Контакт 1 Красный

+ 12В мощность

Контакт 2 Черный

-12V Power

Контакт 3 Черный

Garmin RX1

Контакт 4 Белый

Garmin TX1

Контакт 5 Желтый

Сигнальная земля

Контакт 6 Н/Д

Контакт 7 Н/Д

Контакт 8 Н/Д

Контакт 9 Коричневый

7

ООО "ХарвестТек". Соглашение о гарантии и ответственности
Харвест Тех, ООО. отремонтирует или заменит компоненты, в которых будут обнаружены дефекты, в течение 12 месяцев с даты изготовления. Ни при каких обстоятельствах эта гарантия не распространяется на компоненты, которые, по мнению Harvest Tec, LLC. подвергались небрежному использованию, неправильному использованию, модификации, аварии или ремонту с использованием деталей, отличных от тех, которые произведены и получены от Harvest Tec, LLC.
Наши обязательства по данной гарантии ограничиваются бесплатным ремонтом или заменой первоначальному покупателю любой детали, которая, по нашему мнению, имеет признаки дефекта или ненадлежащего качества изготовления, при условии, что эта деталь будет возвращена Harvest Tec, LLC. в течение 30 дней с момента отказа. Если будет установлено, что в системе аппликатора Harvest Tec использовался консервант для сена другой марки, где произошел сбой, то Harvest Tec оставляет за собой право отказать в гарантийном запросе по своему усмотрению. Детали должны быть возвращены через дилера и дистрибьютора, предварительно оплатив транспортные расходы.
Эта гарантия не должна толковаться как предоставление Harvest Tec, LLC. ответственности за вред или ущерб любого рода, прямой, косвенный или случайный, лицам или имуществу. Кроме того, эта гарантия не распространяется на потерю урожая, убытки, вызванные задержками или любыми расходами, предполагаемой прибылью или по любой другой причине. Харвест Тех, ООО. не несет ответственности за возмещение суммы, превышающей стоимость или ремонт дефектов изготовления.
Нет никаких явных или подразумеваемых гарантий товарной пригодности или пригодности для конкретной цели или пригодности по любой другой причине.
Эта гарантия не может гарантировать, что существующие условия находятся вне контроля Harvest Tec, LLC. не повлияет на нашу способность получать материалы или производить необходимые запасные части.
Harvest Tec, LLC. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold.
Пересмотрено 6 ноября
ХАРВЕСТ ТЭК, ООО. а/я 63
2821 ХАРВИ-СТРИТ ХАДСОН, Висконсин 54016
PHONE: 715-386-9100 1-800-635-7468
ФАКС: 715-381-1792 Электронная почта: [электронная почта защищена]
8

Документы / Ресурсы

HARVEST TEC 880GPS GPS Attachment [pdf] Руководство пользователя
880GPS, GPS Attachment, 880GPS GPS Attachment, Attachment, GPS

Оставить комментарий

Ваш электронный адрес не будет опубликован.