ORTUR Laser Master 2 S2 LU2-2 and Rotary Roller Instruction Manual

1. Введение

This manual provides essential instructions for the safe and effective operation of your ORTUR Laser Master 2 S2 LU2-2 laser engraver and the ORTUR Laser Rotary Roller (YRR2.0). Please read this manual thoroughly before use to ensure proper setup, operation, and maintenance.

2. Информация по технике безопасности

WARNING: This product is a Class 4 laser device. Direct exposure to the laser beam can cause severe eye and skin damage. Always wear appropriate laser safety goggles during operation.

The ORTUR Laser Master 2 S2 LU2-2 incorporates several safety features:

• Защита G-сенсора: Если гравировальный станок сместится или наклонится во время работы, лазер автоматически остановится.
• Laser Beam Stop Protection: If the computer system halts or the USB cable disconnects, causing the engraver to stop moving, the laser beam will automatically cease to prevent fire hazards.
• Idle Laser Shutdown: If the machine is powered on but remains stationary for an extended period, the laser will automatically turn off.
• Конструкция средств защиты глаз: The panoramic filter glass protective cover filters 97% of ultraviolet light, reducing the need for additional goggles. However, wearing safety goggles is still highly recommended.

Image: ORTUR Laser Master 2 S2 LU2-2 showing dimensions (390x410mm engraving area) and four key safety features: Exposure Duration Detection, Laser Beam Safety Guard, Power Control System, and Position Movement Protection.

3. Особенности продукта

3.1. Laser Engraver (Laser Master 2 S2 LU2-2)

• High-Performance Motherboard: Equipped with a 32-bit professional motherboard and ORTUR Laser 1.8 firmware, enabling faster and more precise operations with stepper motor speeds up to 5000 mm/min.
• Ultra-Fine Compression Laser: Features a 2100mW output laser with an ultra-fine focal area reduced to 0.07*0.06mm, allowing for detailed engraving.
• Большая область гравировки: Provides a generous engraving area of 390*410mm.

Image: Comparison of the LU2-2's new compressed spot technology (0.07*0.06mm) versus other lasers (0.23*0.23mm), demonstrating finer detail in engraving results.

Image: Close-up of the 32-bit professional motherboard, highlighting its advanced components for increased speed and accuracy.

3.2. Laser Rotary Roller (YRR2.0)

• Cylindrical Object Engraving: Designed for engraving on cylindrical or small-diameter objects such as round wood, cups, bottles, pipes, bowls, guitars, drums, and tubes.
• Adjustable Diameters: Features 7 adjustable diameters, accommodating objects from 8mm to 100mm.
• Bracket Support: Includes a bracket with wheels to provide stable support for items like wine glasses during engraving.

Image: Diagram illustrating the 7 adjustable gear positions on the rotary roller, allowing for engraving on objects with diameters from 8mm to 100mm.

4. Настройка

4.1. Laser Engraver Assembly

The ORTUR Laser Master 2 S2 LU2-2 requires assembly. Follow the detailed instructions provided in the separate assembly guide included with your product. Ensure all components are securely fastened before proceeding.

4.2. Rotary Roller Installation (Optional)

To use the rotary roller, connect it to the laser engraver according to the rotary roller's specific installation instructions. Ensure it is properly aligned and secured for stable operation.

4.3. Установка программного обеспечения

The ORTUR laser engraver is compatible with various engraving software:

• ЛазерGRBL: Free software, widely used for basic engraving tasks.
• Лайтберн: Paid software, offering advanced features and greater control.

Загрузите и установите предпочитаемое программное обеспечение с официального сайта. websites. Ensure your computer meets the system requirements:

• Операционные системы: Windows 7 / 8 / XP / 10 / 11, macOS, Linux.

Connect the engraver to your computer via USB after software installation.

5. Инструкция по эксплуатации

5.1. Basic Engraving Process

1. Подготовьте материал: Place your chosen material securely on the engraving bed.
2. Сфокусируйте лазер: Adjust the laser module height to achieve the optimal focal point on the material surface. Refer to your assembly guide for specific focusing methods.
3. Расчет нагрузки: Open your engraving software (e.g., LaserGRBL, LightBurn) and load your desired design file.
4. Установить параметры: Configure engraving parameters such as power, speed, and passes based on the material type and desired effect.
5. Предварительноview и позиция: Используйте предустановленные функции программного обеспечения.view function to ensure the design is correctly positioned on the material.
6. Начать гравировку: Запустите процесс гравировки из программного обеспечения. Always wear laser safety goggles during operation.

5.2. Using the Rotary Roller for Cylindrical Engraving

When engraving cylindrical objects, replace the standard engraving bed with the ORTUR Laser Rotary Roller. Ensure the object is securely placed on the rollers and properly aligned.

Image: The ORTUR Laser Rotary Roller in action, demonstrating 360-degree rotating engraving on a cylindrical object (e.g., a can), with a bracket providing support for items like wine glasses.

Adjust the rotary roller's diameter settings to match your object. In your engraving software, select the rotary engraving mode and adjust parameters accordingly. The machine will rotate the object while the laser engraves, creating a seamless design around its circumference.

5.3. Совместимые материалы

The ORTUR Laser Master 2 S2 LU2-2 can engrave on a wide range of materials, including but not limited to:

• Бумага
• Бамбук
• Древесина
• Кожа
• Печатная плата
• оксид алюминия
• Metal (engraving only, not cutting)
• Glass (with appropriate preparation)

Изображение: Бывшийamples of various items engraved using the ORTUR laser engraver, including wine glasses, bottles, tumblers, rolling pins, rings, and pens, showcasing its wide applicability.

6. Техническое обслуживание

• Чистая лазерная линза: Regularly inspect and clean the laser lens using a soft, lint-free cloth and appropriate lens cleaning solution to maintain optimal engraving quality.
• Очистить мусор: Remove any dust, smoke residue, or material debris from the engraving area and machine components after each use.
• Смажьте движущиеся части: Periodically lubricate the guide rails and lead screws with a suitable lubricant to ensure smooth movement.
• Проверьте соединения: Убедитесь, что все кабели и соединения надежны и не имеют повреждений.

7. Поиск Неисправностей

• Лазер неожиданно остановился:
  • Check if the machine was bumped or tilted (G-sensor activated).
  • Verify USB cable connection to the computer.
  • Ensure the computer system is not halted.
  • If idle for too long, the laser will shut off automatically; restart the engraving process.
• Низкое качество гравировки:
  • Убедитесь, что лазер правильно сфокусирован на поверхности материала.
  • Очистите линзу лазера от пыли и остатков материала.
  • Adjust engraving power and speed settings for the specific material.
• Машина не отвечает:
  • Проверьте электропитание и соединения.
  • Verify USB connection to the computer.
  • Restart the engraving software and the machine.

8. Технические характеристики

8.1. ORTUR Laser Master 2 S2 LU2-2

8.2. ORTUR Laser Rotary Roller (YRR2.0)

Image: Detailed specifications and dimensions of the ORTUR Laser Rotary Roller YRR2.0, showing its physical measurements.

9. Гарантия и поддержка

For warranty information and technical support, please refer to the documentation included with your product or visit the official Ortur website. You can also contact Ortur customer service for assistance with any issues or questions regarding your device.

Официальный Ортур Webсайт: www.ortur.net