Nillkin SnapHold Magnetic Wall Mount for MagSafe Compatible Devices

1. Введение

The Nillkin SnapHold Magnetic Wall Mount provides a convenient and secure way to mount your MagSafe-compatible iPhone or device on various flat surfaces. This product is designed for hands-free use in locations such as bathrooms, kitchens, gyms, and bedrooms, allowing you to enjoy media, video calls, or follow instructions without holding your device. The strong magnetic attraction ensures your device remains firmly in place.

2. Совместимость продукции

The Nillkin SnapHold Magnetic Wall Mount is designed for optimal compatibility with:

• iPhone 17 Pro Max/17 Pro/17/16/15/14/13/12 Series
• MagSafe Cases
• Nillkin Magnetic Cases
• Devices with MagSafe rings

Note: This product is not suitable for use in vehicles.

Image: Compatibility chart for Nillkin SnapHold Magnetic Sticker.

3. Настройка и установка

Follow these steps to properly install your Nillkin SnapHold Magnetic Wall Mount:

1. Подготовка поверхности: Choose a clean, flat, and dry surface for installation. Wipe the surface thoroughly to remove any dust, dirt, or moisture.
2. Remove Release Paper: Carefully peel off the protective release paper from the adhesive side of the magnetic sticker.
3. Наклейте стикер: Press the magnetic sticker firmly onto the prepared surface. Apply pressure for a few seconds to ensure strong adhesion.
4. Разрешить установку: For optimal adhesion and stability, allow the sticker to set for at least 12 hours before attaching your device.

Important: Do not stick the magnetic sticker directly onto your phone. It is designed to be affixed to a wall or other flat surface. Avoid removing and re-pasting the sticker, as this will decrease its adhesiveness.

Image: Step-by-step installation guide for the SnapHold Magnetic Sticker.

Image: Correct and incorrect application of the magnetic sticker.

4. Инструкция по эксплуатации

Once the SnapHold Magnetic Wall Mount is securely installed, using it is simple:

• Прикрепить устройство: Bring your MagSafe-compatible iPhone (or device with a MagSafe case/ring) close to the installed magnetic sticker. The strong rubidium magnet will automatically attract and secure your device.
• Отрегулируйте положение: The magnetic connection allows for easy rotation and adjustment of your device's orientation (portrait or landscape) to suit your viewпотребности.
• Удалить устройство: Gently pull your device away from the magnetic sticker to detach it.

Image: Various application scenarios for the magnetic phone holder.

Image: Specific examples of the phone holder in use in a bathroom, gym, and bedroom.

5. Техническое обслуживание

To ensure the longevity and performance of your Nillkin SnapHold Magnetic Wall Mount:

• Keep the magnetic surface clean and free from debris.
• Avoid exposing the adhesive to extreme temperatures or direct sunlight for prolonged periods, as this may weaken the bond.
• Do not attempt to reposition the sticker after initial application, as this will compromise its adhesive strength.

6. Поиск Неисправностей

If you encounter any issues with your magnetic wall mount, consider the following:

• Weak Adhesion: Ensure the surface was thoroughly cleaned and dry before application. Avoid touching the adhesive side during installation. Allow the recommended 12-hour setting time. If the sticker has been repositioned multiple times, its adhesive may be compromised.
• Устройство не зависает: Verify that your phone or case is MagSafe compatible or has a built-in magnetic ring. Ensure there are no obstructions between your device and the magnetic sticker.
• Device Falling: Check if the magnetic sticker is firmly attached to the wall. Ensure the device's weight does not exceed the magnetic holder's capacity (800g magnetic attraction).

7. Технические характеристики

8. Гарантия и поддержка

Your Nillkin SnapHold Magnetic Wall Mount comes with a Гарантия 12 месяца. For any product issues, concerns, or dissatisfaction, please contact Nillkin customer support directly for assistance.