LiteBee Flysky FS-GR3E 3CH RC Receiver User Manual

1. Введение

The LiteBee Flysky FS-GR3E is a compact and reliable 3-channel 2.4Ghz AFHDS receiver designed for use with various Flysky transmitters in RC car and boat applications. This manual provides essential information for proper setup, operation, and maintenance of your receiver.

2. Информация по технике безопасности

• Always ensure correct polarity when connecting power to avoid damage to the receiver or other components.
• Operate your RC model in open areas, away from people, vehicles, and obstacles to prevent accidents.
• Regularly check all connections for security and proper seating before each operation.
• Keep the receiver away from moisture, water, and extreme temperatures to ensure optimal performance and longevity.
• Do not attempt to modify the receiver. Unauthorized modifications may void the warranty and lead to malfunction or damage.

3. Содержимое упаковки

• 1 x LiteBee Flysky FS-GR3E 2.4Ghz 3CH Receiver

4. Технические характеристики

Figure 1: Dimensions of the FS-GR3E receiver.

5. Настройка

5.1 Физическое соединение

This section details the physical connection of the FS-GR3E receiver to your RC model's components.

1. Connect the steering servo to Канал 1 на ресивере.
2. Connect the Electronic Speed Controller (ESC) or throttle servo to Канал 2 на ресивере.
3. Connect any auxiliary functions (e.g., lights, additional servos) to Канал 3. This port is also used for binding.
4. Ensure the power input (4-11V DC) is supplied to the receiver, typically through the ESC or a dedicated battery connected to the VCC port.

Figure 2: LiteBee Flysky FS-GR3E 3CH RC Receiver with labeled ports for connection.

Рисунок 3: Подробная информация view of the receiver's connection ports, including the BIND/CH3 port.

Рисунок 4: Example of the FS-GR3E receiver connected within an RC car setup.

5.2. Процесс связывания

The binding process links your FS-GR3E receiver to your Flysky transmitter, establishing a unique communication link. This process ensures that your receiver only responds to commands from your specific transmitter.

1. Убедитесь, что ваш передатчик Flysky выключен.
2. Insert the binding plug (a small jumper wire or dedicated plug, often included with your transmitter or receiver) into the BIND/CH3 порт на приемнике FS-GR3E.
3. Включите приемник. Светодиод на приемнике должен быстро мигать, указывая на то, что он находится в режиме привязки.
4. Удерживая СВЯЗЫВАТЬ button on your Flysky transmitter (if available, or follow your transmitter's specific binding procedure), power on the transmitter.
5. Светодиод на приемнике должен перестать мигать и загореться постоянно, что указывает на успешное сопряжение.
6. Отпустите кнопку BIND на передатчике.
7. Power off both the receiver and the transmitter.
8. Извлеките клеммную колодку из приемника.
9. Power on the transmitter first, then the receiver. The receiver's LED should illuminate solid, confirming the connection.
10. Test all channels (steering, throttle, etc.) to ensure proper operation before using the model.

5.3. Совместимость

The FS-GR3E receiver is compatible with Flysky transmitters utilizing the AFHDS protocol. Refer to the compatibility chart below for specific models.

Figure 5: Flysky receiver compatibility chart, indicating which transmitters work with various receivers, including the GR3E.

6. Инструкция по эксплуатации

• Последовательность включения питания: Always power on your transmitter first, then power on your RC model (receiver). This ensures the transmitter is broadcasting a signal before the receiver attempts to connect.
• Последовательность выключения: Always power off your RC model (receiver) first, then power off your transmitter. This prevents unintended movements due to loss of signal while the model is still powered.
• Отказоустойчивая функция: The FS-GR3E features a failsafe on Channel 2 (throttle). In case of signal loss or low battery, the failsafe will automatically set the throttle to a pre-programmed position (usually neutral or brake) to prevent the model from running away. Refer to your transmitter's manual for instructions on setting failsafe values.
• After powering on, observe the receiver's LED. A solid LED indicates a successful connection to the transmitter.

7. Техническое обслуживание

• Уборка: Содержите приёмник в чистоте, не допускайте попадания пыли, грязи и влаги. Используйте для чистки мягкую сухую ткань. Не используйте растворители и агрессивные химикаты.
• Соединения: Periodically check all wiring and connections for wear, damage, or looseness. Secure any loose connections.
• Антенна: Ensure the antenna is properly positioned and not damaged. Avoid bending, coiling, or cutting the antenna wire, as this can significantly reduce range and signal quality.
• Хранилище: Store the receiver in a dry, cool place when not in use. Protect it from physical impact and static electricity.

8. Поиск Неисправностей

• Приёмник не получает питания:
  • Проверьте соединения аккумулятора и убедитесь, что аккумулятор заряжен.
  • Verify correct polarity of power connections to the receiver.
  • Ensure the Electronic Speed Controller (ESC) or external power source is functioning correctly.
• Приёмник не привязан:
  • Confirm the binding plug is correctly inserted into the BIND/CH3 port.
  • Ensure the transmitter is in binding mode according to its manual.
  • Verify that the transmitter and receiver are compatible (both use the Flysky AFHDS system).
  • Try binding in a location away from other 2.4GHz devices that might cause interference.
• Intermittent Signal / Short Range:
  • Проверьте наличие физических препятствий между передатчиком и приемником.
  • Ensure the receiver antenna is not damaged, coiled, or shielded by carbon fiber or metal parts within the model.
  • Avoid operating near strong electromagnetic interference sources (e.g., power lines, large metal structures).
  • Check the transmitter battery level.
• Servos/ESC Not Responding:
  • Verify that the receiver is successfully bound to the transmitter (solid LED).
  • Check servo/ESC connections to the correct receiver channels.
  • Ensure servos/ESC are powered and functioning independently.

9. Гарантия и поддержка

For warranty claims or technical support regarding your LiteBee Flysky FS-GR3E receiver, please contact your original retailer or the manufacturer directly. It is recommended to retain your proof of purchase for warranty validation.