RSG logo

Limited Life Protective Clothing

– Instructions For Use

  • These garments are limited use protective clothing manufactured to meet the requirements of PPE regulation 2016/425 and PPE standard EN13688: protective clothing general requirements.
  •  Manufactured under ISO 9001 quality control procedures.
  •  Bag and garment labels indicate producttype.
  •  Selection of the garment suitable for the application is the users final responsibility.
  • Recommended for single use applicationsonly.
  •  Ensure all seams and closures are intact. Worn, damaged or contaminated garments should not be used.
  •  No special storage conditionsrequired.
  •  Fabrics with low air permeability can cause heat stress. Frequent rest is advised.
  •  Garments will protect only the parts of the body they cover. Connections with other PPE may require appropriate sealing.
  •  All Type 5 testing has been conducted with face, ankles and wrists sealed with PVC tape. This may be appropriate in some applications.
  •  PB- Partial body protection garments will only protect parts of the body that are covered.
  • Microporous TS Series passes all the tests defined in EN14126:2003 for protection against infective agents. We recommend that the Chemical Workwear range should be used for any hazardous biological protection as it features fully sealed seams.
  •  Uncontaminated garments can be disposed of to landfill or incineration with out harmful effects. Contaminated garments must be disposed of appropriately according to the requirements of the contamination.
  •  Whilst meeting the FR requirements of EN 14116, the standard is primarily for flame protective garments, in which case the standard requires that the fabric should NOT come into contact with skin. However RSG FR range garments are not intended
    to protect against flame but rather to wear over other flame protective garments to provide liquid / dust protection AND improve thermal protection. The requirements of EN 1149 however require that the garment should come into contact with the
    skin at the wrists or face for the Earthing of any static charge through the body. This is contrary to the strict requirements of EN14116. We therefore suggest the user determines the requirements and whether Earthing by contact through skin is
    appropriate given the flame protective requirements
  •  Not suitable for use in extremely low temperatures (sub zero) or temperatures higher than 100 degrees.

– Electrostatic Properties EN1149-5:2018

Fabrics are treated to meet the requirements of EN 1149-1:2006 & EN 1149-5:20
8. EN 1149 is stated in ATEX and German
regulation TRBS 2153 (replacement for BGR 132) as the best determination of suitability for protective clothing in electrostatic dissipative protective clothing is intended to be worn in explosive/oxygen enriched or Zone 0 atmospheres. A risk assessment should
be conducted by qualified personnel. In addition, in any explosive atmosphere: – see EN 60079-10-1 and EN 60079-10-2) in which the minimum ignition energy of any explosive atmosphere is not less than 0,016 mJ;

  • Garments should be worn correctly, fully closed and contact with the skin maintained directly or through other anti-static PPE to allow charge dissipation.
  • The garment should fully cover any non-dissipative clothing during normal use including when bending and moving.
  • The wearer should be properly earthed. Do not adjust or remove in use, clothing shall be worn in such a way that it permanently covers all non-complying materials during normal use (including bending movements). Any footwear or materials between the garment fabric and the floor should have a resistance lower than 2.5 x108 Ohms to allow charge dissipation.
  • Anti-static treatments may fade and may be affected by wear, tear and laundering. Do not re-use.
  • Anti-static testing is conducted in relative humidity of 25% +/- 5%. At lower humidity dissipative properties may be lower. The garment passes the requirement Ljmn, 82/90 ≤30% and Ls, 8/10 ≤15%.”

-Resistance to permeation by chemicals

The Chemical Workwear range, Multi-Use Chemical Workwear FR been tested to EN 369 or EN 374-3 to indicate resistance to chemicals. Tests on the fabric and seams have been conducted. Note that breakthrough times on seams may be lower than
on the fabric. Other chemicals have been tested. Please refer to your supplier for further information.

-Chemical Repellency – EN ISO 6530:2005

Name Type Comfort Workwear GP Microporous NS Series Microporous TS Series RSG Multi Use Workwear FR
Sulphuric Acid 30% -Penetration Class 3 Class 3 Class 3 Class 3
-Repellency Class 3 Class 3 Class 3 Class 3
Sodium Hydroxide 10% -Penetration Class 3 Class 3 Class 3 Class 2
-Repellency Class 3 Class 3 Class 3 Class 2
O-Xylene Unclassified 3/2 NT 3/3
Butan-1-ol Unclassified 3/2 NT 3/3

– Resistance to Permeation by Chemicals – EN ISO 6529:2001
Breakthrough Time in Minutes – Class (Fabric/ Seams) 

Chemical Microporous TS Series Chemical Workwear CHEM 1
Series
Chemical Workwear CHEM 2
Series
Chemical Workwear CHEM 3
Series
RSG Multi Use Chemical
Workwear FR
Sulphuric Acid 98% Class 2 Class 6 Class 6 Class 6 Class 1
Sodium Hydroxide
10%
Class 6 Class 6 Class 6 Class 6 Class 6
O-Xylene NT NT NT Class 6 NT
Butan-1-ol NT Class 6 Class 6 Class 6 NT

Technical Properties

– Material Performance Data

Test Comfort
Workwear
GP
RSG-100-
CW
Mcroporous NS Series RSG-100- MPNSS Cool
Workwear
RSG-
100CSW
Mcroporous
TS Series
1080-
Multi-use
Workwear
10100
Multi-use
Chemical
Workwear FR
10110
Chemical Workwear Chem 1 10020- Chemical Workwear Chem2 10030- Chemical Workwear Chem3 10040-
EN530 Abrasion Class 2 Class 3 Class 2 Class 3 Class 2 Class 6 Class 2 Class 6 Class 6
EN863 Puncture Class 1′ Class 1′ Class 1′ Class le Class 2 Class 2 Class 2 Class 2 Class 2
IS02960 Burst Class 2 Class 2 Class 1 Class 1 Class 3 Class 2 Class 1 Class 2 Class 2
IS07854 Flex
Cracking
Class 6 Class 6 Class 6 Class 6 Class 6 Class 5 Class 1 Class 6 Class 4
IS09073 Tear MD – 2
CD – 2
MD – 3 CD – 1 MO – 3
CD – 2
MO – 3
CD – 2
MD – 4
CD – 3
MD – 2
CD – 2
MD – 3
CD – 3
MD – 6
CD – 4
MD – 4
CD – 3
IS013934 Tensile Class 3 MD – 2 CD – 1 MO – 2 CO – 1 Class 2 Class 2 Class 3 MD – 3
CD – 2
MD – 3
CD – 2
Class 2
EN1149-5 Anti-stat Pass Pass Pass Pass Pass Pass Pass Pass Pass

* Radioactive particulate contamination Puncture resistance must be Class 2 to conform to  EN1073-2 (*denotes non conformance)
– Finished Garment Tests

Comfort
Workwear
GP
RSG-100-
CW
Microporous
NS Series
RSG-100-
MPNSS
Cool
Workwear
RSG-
100CSW
Microporous
TS Series
1080-
Multi-use
Workwear
10100
Multi-use
Chemical
Workwear
FR
10110
Chemical
Workwear
Chem1
10020-
Chemical
Workwear
Chem2
10030-
Chemical
Workwear
Chem3
10040-
EN13034:2005 Type 6
EN13982-1:2004 Type 5
EN14605:2004 Type 4
EN14605:2004 Type 3 V
EN1073-2:2002 Class 1 Class 1 Class 1 Class 1 Class 1 Class 1 Class 1 Class 1
1505082 Seam Strength Class 3 Class 3 Class 3 Class 3 Class 3 Class 4 Class 3 Class 4 Class 4
IS014116:2015 Limited Flarre Spread Index 1′ Index 1′

*Radioactive particle contamination *Index 1 to be worn with Index 2 garment
– Protection against infective agents EN14126:2003

Test No. Description Result
ISO 16604:2004 Protection against blood & body fluids. Pass- Class 6
ISO 22611:2003 Protection against biologically contaminated aerosols Pass- Class 3
ISO 22612:2005 Protection against dry microbial penetration. Pass- Class 3
EN 14126:2003, Annex A Protection against mechanical contact with substances containing contaminated liquids. Pass- Class 6

– Garment Sizes

RSG 100  MPNSS Test Strip Cutting Module - Garment 11

Select appropriate size for users chest and height.

Body Chest
Size Height (cm) Girth (cm)
S 164- 170 84- 92
M 170- 176 92- 100
L 176- 182 100-108
XL 182- 188 108- 116
2XL 189- 194 116- 124
3XL 194- 200 124-132

RSG 100  MPNSS Test Strip Cutting Module - icon 14

– Explanation of Symbols

RSG 100  MPNSS Test Strip Cutting Module - icon Type 6: EN13034: 2005. Reduced Chemical Spray.
RSG 100  MPNSS Test Strip Cutting Module - icon 1 Chemical protective suits have been tested tothe whole suit test (5.2)  Type 5: EN13982-1: 2004. Dry Particle Protection.
This suit passes the requirement Ljmn82/90 <30% and Ls8/10 < 15%
RSG 100  MPNSS Test Strip Cutting Module - icon 2 Type 4: EN14605: 2005. Chemical Spray.
RSG 100  MPNSS Test Strip Cutting Module - icon 3 Type 3: EN14605: 2005. Liquid Tight Seams.

PB suit test(5.2) Partial Body protection Type 6/4/3.
Type PB[6] partial bodyprotection hasnotbeentested tothe whole
RSG 100  MPNSS Test Strip Cutting Module - icon 4 Protection against radioactive contaminated particles- EN1073-2:2002
Class 1: Nominal protection factor >5<50.
RSG 100  MPNSS Test Strip Cutting Module - icon 6 Electrostatic properties – Surface resistivity – EN1149-5:2018
Garments are treated to be static dissipative onthe inside surface.
RSG 100  MPNSS Test Strip Cutting Module - icon 10 Protection against infective agents EN 14126:2003.
Type 4B/5B/6B
read this guide Refer to further instructions over leaf.
RSG 100  MPNSS Test Strip Cutting Module - icon 11 Do not re-use.
RSG 100  MPNSS Test Strip Cutting Module - icon 12 Protection against heat and flame EN ISO 11416:2015. *Warning triangle denotes that this should be worn with anIndex 2 garment

Note: The Cool Workwear may have reduced protection on the back breathable panel.
The Overboots and Overshoes will only protect the part of the body they are covering – the feet and should be worn in conjunction with a coverall should the wearer need all over body protection.
The Laboratory Workwear is PB and will only protect the parts of the body covered.

– Washing Instructions

RSG 100  MPNSS Test Strip Cutting Module - icon 15

-Approvals

CE Approvals by:

BTTG Manufactured on behalf of:
Unit 14 Wheel Forge WayRSG Safety BV
Trafford Park Marinus
Manchester Dammeweg 38,
M17 1EH5928 PW Venlo,
United Kingdom
NotifedBodyNo.0338The Netherlands
SATRA Technology
Europe Ltd, Bracetown
Business Park, Clonee,
Dublin, D15 YN2P
Ireland
Notified Body No. 2777

Download declaration of conformity @ www.rsgsafety.com in the various languages.

Documents / Resources

RSG 100- MPNSS Test Strip Cutting Module [pdf] Instruction Manual
100- MPNSS, 100- MPNSS Test Strip Cutting Module, Test Strip Cutting Module, Cutting Module

References

Leave a comment

Your email address will not be published. Required fields are marked *