MP Series Turbo Immersion Blender
“
Specifications:
- Brand: Robot Coupe
- Model: Immersion Blender
- Warranty: One Year Limited Commercial Warranty
Product Usage Instructions:
Introduction:
Welcome to your new Immersion Blender from Robot Coupe. Please
read the following instructions carefully to ensure safe and
efficient operation of your device.
Operating the Immersion Blender:
1. Plug the device into a compatible power outlet following the
power supply guidelines.
2. Press the power button to start the blender.
3. Use the immersion blender to mix, blend, or puree ingredients
as needed.
Working Position:
Hold the immersion blender firmly with one hand while operating
it with the other hand. Ensure a stable working position to prevent
accidents.
Assembly & Disassembly:
When assembling or disassembling the blender for cleaning or
maintenance, follow the guidelines provided in the user manual to
avoid any damage to the device.
Cleaning and Maintenance:
After each use, detach the blending attachment and clean it
thoroughly with warm soapy water. Ensure all parts are completely
dry before reassembling.
Regular maintenance is essential to keep your immersion blender
in optimal condition. Refer to the manual for detailed maintenance
instructions.
FAQ:
What should I do if my immersion blender stops working?
If your immersion blender stops working, check the power supply
connection, and ensure the device is assembled correctly. If issues
persist, refer to the troubleshooting section in the user manual or
contact customer service.
How often should I clean my immersion blender?
We recommend cleaning your immersion blender after each use to
prevent food residue buildup and maintain hygiene standards.
Regular cleaning will also prolong the life of your device.
“`
New
Register your product
on line
Robot Coupe U.S.A., Inc. 264 South Perkins, Ridgeland, MS 39157 Phone: 800/824-1646 · 601/898-8411 email: info@robotcoupeusa.com – website: www.robot-coupe.com
· MP 350 Turbo · MP 350 Turbo V.V. · MP 450 Turbo · MP 450 Turbo V.V. · MP 550 Turbo · MP 600 Turbo · MP 800 Turbo · MP 350 Turbo Combi · MP 450 Turbo Combi · MP 450 Turbo FW · MP 450 Turbo FW XL
03/11/2022
IMPORTANT WARNING
WARNING
KEEP THESE INSTRUCTIONS IN A SAFE PLACE
WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get to know your appliance and enable you to use the equipment correctly. Please read these instructions in their entirety and make sure that anyone else who may use the appliance also reads them beforehand. Our equipment is designed for professional use and must not be used by children under any circumstances.
UNPACKING
· Carefully remove the equipment from the packaging and take out all the boxes or packets containing attachments or specific items. · WARNING – some of the tools are very sharp e.g. blades, discs… etc.. · Store manuals, tools and spare parts in a safe place available to the users of the machine
CONNECTION
· Always check that your power supply corresponds to that indicated on the identification plate on the motor unit and that it can withstand the amperage. · The unit must always be connected to a grounded outlet with Ground Fault Circut Interrupter (GFCI) protection device.
HANDLING
· Always take care when handling the blades, asthey are extremely sharp. · Wear cut-proof gloves when handling the blades.
03/11/2022
USE
· The machine must not be modified in any way from its original configuration. · Never tamper with, or defeat the purpose of the locking and safety systems. · Do not leave the machine running unattended. · The machine must be operated and stored in a location not subject to water drips or spray or explosive vapors. · Should the machine malfunction or should any part be damaged, it must not be operated until it is repaired by a qualified technician using only genuine Robot Coupe repair parts. · Failure to follow these operating instructions or attempts to operate the machine outside its design limits may create a hazardous condition that could damage the machine and/or injure users. Special attention should be given to the use of the operation controls and safety features.
CLEANING
· As a precaution, always unplug your appliance before cleaning it.
· Always clean the appliance and its attachments at the end of each cycle. · Never immerse the motor base in water. · For parts made from aluminum, use metal safe detergents intended for aluminum. · Caustic detergents used in automatic dishwashers quickly degrade plastic parts. Hand wash plastic parts if possible. · Robot Coupe can in no way be held responsible for the user’s failure to follow the basic rules of cleaning and hygiene.
MAINTENANCE
· Do not open the motor housing. There are no user serviceable components inside the electrical housing. Refer control component repairs to qualified technicians. · It is particularly important to maintain and check the attachments since certain ingredients contain corrosive agents, e.g. citric acid. · Never operate the appliance if the power cord or plug has been damaged or if the appliance fails to work properly or has been damaged in any way.
www.robotcoupeusa.com
Register your product online
We reserve the right to alter at any time without notice the technical specifications of this appliance. None of the information contained in this document is of a contractual nature. Modifications may be made at any time. © All rights reserved for all countries by: ROBOT-COUPE S.N.C.
CONTENTS
WARRANTY
IMPORTANT WARNING
· Unpacking · Storage · Power supply · Specifications · Dimensions · Safety features · Warning
INTRODUCTION TO YOUR NEW IMMERSION BLENDER
OPERATING THE IMMERSION BLENDER
· Operation · Continuous operation · Variable-speed operation · Mashed potatoes function · Power cord
WORKING POSITION
· Function blade · Function whisk
ASSEMBLY & DISASSEMBLY
· Function blade · Function whisk · Mixing tool function
CLEANING
· Motor housing · Tube and bell · Blade · Aluminum · Plastic · Whisk gearbox · Whisks · Mixing tool housing · Mixing tool
MAINTENANCE
· Blade · Whisks · Power cord · Tube Seal · Seal Ring · Cartridge
TROUBLE SHOOTING
SERVICE
ELECTRICAL AND WIRING DIAGRAMS
03/11/2022 3
ROBOT COUPE U.S.A., INC. ONE YEAR LIMITED COMMERCIAL WARRANTY
YOUR NEW ROBOT COUPE COMMERCIAL PRODUCT IS WARRANTED TO THE ORIGINAL PURCHASER FOR A PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE. This LIMITED COMMERCIAL WARRANTY is against defects in the material and / or workmanship, and includes labor for replacement of defective parts, provided repairs are performed by an authorized service agency (see attached list). The CUSTOMER must inform the Service Agency of the possibility of warranty coverage and provide a copy of the dated sales or delivery receipt BEFORE WARRANTY REPAIRS ARE BEGUN. All parts or accessories replaced under warranty must be returned to the Service Agency. The warranty for work done or parts replaced under warranty expires at the end of the original warranty period. Replacement parts and accessories are warranted for ninety (90) days from the date of purchase when purchased separately and will be verified by dated sales receipt OR packing slip which list that item. All Robot Coupe Products are considered commercial use only.
4 03/11/2022
THE FOLLOWING ARE NOT COVERED UNDER WARRANTY:
1 – Damage caused by abuse, misuse, dropping, or other similar incidental damage caused by or as result of failure to follow installation, assembly, operating, cleaning, user maintenance or storage instructions, including failure to verify and correct rotation of three phase motors.
2 – Labor to sharpen and/or parts to replace knife assemblies or blades which have become dull, chipped, or worn due to normal use.
3 – Material or labor to renew or repair scratched, stained, chipped, dented, or discolored surfaces, blades, knives, attachments, or accessories.
4 – Transportation charges to or from an authorized service agency for repairs of a machine designated as “CARRY IN SERVICE” (Table Top Models).
5 – Labor charges to install or test attachments or accessories (i.e. bowls, cutting plates, blades, attachments) which are replaced for any reason.
6 – Charges to change Direction-of-Rotation of Three Phase electric motors (INSTALLER IS RESPONSIBLE). All Robot Coupe products must operate counter-clock-wise.
7 – SHIPPING DAMAGE IS NOT COVERED BY WARRANTY. Visible and hidden damages are the responsibility or the freight carrier. The consignee must file a damage claim promptly against the carrier, or upon discovery in the case of hidden damage.
8 – Any ROBOT COUPE COMMERCIAL PRODUCT used in an Industrial application.
Commercial equipment use is defined as but not limited to the preparation of food substance within the confines of a restaurant/facility, that is sold and consumed within said restaurant/facility.
Industrial equipment use is defined as but not limited to the manufacturing of food substance in large batch quantities. The processed food is then packaged and sold off site and or to a distributer for resale off site.
KEEP ALL ORIGINAL CONTAINERS AND PACKING MATERIALS FOR CARRIER INSPECTION
All Robot Coupe equipment should be operated in an ambient room temperature of 60 degrees (F) or higher.
Robot Coupe U.S.A., Inc., Robot Coupe S.A., or any of their affiliates, distributors, officers, directors, agents, employees or insurers will not be obligated for consequential or other damages, losses, or expenses in connection with or by reason of the use of or the inability to use the machine for any purpose.
THIS WARRANTY IS GIVEN EXPRESSLY AND IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, FOR MERCHANTABILITY AND FOR FITNESS TOWARD A PARTICULAR PURPOSE AND CONSTITUTES THE ONLY WARRANTY MADE BY ROBOT COUPE, U.S.A., Inc.
IMPORTANT WARNING
WARNING
KEEP THESE INSTRUCTIONS IN A SAFE PLACE
WARNING: In order to limit accidents such as electric shocks, personal injury or fire, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get to know your appliance and enable you to use the equipment correctly. The operation manual should be kept within easy access to all users for reference and should be read completely by all first time users of the machine. Our equipment is designed for professional use and must not be used by children under any circumstances.
UNPACKING
· Carefully remove the equipment from the packaging and take out all the boxes or packets containing attachments or specific items. · Warning- Some parts are very sharp e.g.blade.Wear cutting gloves when handling the blade.
STORAGE
· You are advised to install the wall bracket provided with the machine and to store your Immersion Blender on it. Hang the Immersion Blender with the motor unit UP.
POWER SUPPLY
a. Connect the Immersion Blender to 110-120 Volt 60 Hz Power supply.
b. Connect the Immersion Blender only to Ground Fault Interrupt (GFI) Safety type outlet.
c. Do not connect the Immersion Blender with extension type power cord.
d. GFI type outlets protect the machine from expensive damage and protect the operator from serious injury or death.
SPECIFICATIONS
· MP 350 Turbo – 120V/60Hz / 5,5 Amp. “Series C” · MP 450 Turbo – 120V/60Hz / 0,6 Amp. “Series C” · MP 550 Turbo – 120V/60Hz / 0,7 Amp. “Series C” · MP 600 Turbo – 120V/60Hz / 7,7 Amp. “Series C” · MP 800 Turbo – 120V/60Hz / 8,3 Amp. “Series C · MP 350 Turbo V.V. “Series C” · MP 350 Turbo Combi
“Series C” – 120V/60Hz / 5,5 Amp. · MP 450 Turbo V.V. “Series C” · MP 450 Turbo Combi
“Series C”. · MP 450 Turbo FW “Series C” · MP 450 Turbo FW XL “Series C” – 120V/60Hz / 6 Amp.
DIMENSIONS (In Inches)
1
2
3
i i
B
B
A
B
H
E
B
F
C
G D
E D
D
F
C
C
1
A
MP 350 Turbo
A = 05 B = 28 35/64 C = 03 15/16 D = 14 11/64 I = 06 15/16
MP 350 Turbo V.V.
A = 05 B = 28 35/64 C = 03 15/16 D = 14 11/64 I = 06 15/16
MP 450 Turbo A = 05 B = 32 31/64 C = 03 15/16 D = 18 07/64 I = 06 15/16
2
MP 450 Turbo V.V.
A = 05 B = 32 31/64 C = 03 15/16 D = 18 07/64 I = 06 15/16
MP 550 Turbo
A = 05 B = 36 27/64 C = 04 21/64 D = 21 03/64 I = 06 15/16
MP 600 Turbo
A = 05 B = 38 03/32 C = 04 03/16 D = 22 53/64 I = 06 15/16
3
MP 800 Turbo
A = 05 B = 45 03/16 C = 04 21/64 D = 29 39/64 G = 08 03/9 H = 07 04/9 I = 06 15/16
MP 350 Turbo Combi
A = 5 B = 30 33/64 C = 03 15/16 D = 16 09/64 E = 17 21/64 F = 04 47/64 I = 06 15/16
MP 450 Turbo Combi
A = 5 B = 34 29/64 C = 03 15/16 D = 20 05/64 E = 17 21/64 F = 04 47/64 I = 06 15/16
MP 450 Turbo FW
A = 5 B = 31 11/16 E = 17 21/64 F = 04 47/64 I = 06 15/16
MP 450 Turbo FW XL A = 05 29/32 B = 46 11/4 C = 32 17/64 D = 06 07/8
Blade Attachment Capacities
· Thanks to a very powerful motor, the MP 350 Turbo can process up to 50 quarts, the MP 450 Turbo up to 100 quarts, the MP 550 Turbo up to 200 quarts, the MP 600 Turbo up to 300 quarts and the MP 800 Turbo up to 400 quarts. The quality of the finished product is outstanding.
Whisk Attachment Capacities
· Using the whisk attachment all three models process from 2 to 50 egg whites and 30 kg of mashed potatoes or 60 litre of industrial puree. When the mixing tool attachment (FW XL) is used, the MP 450 FW XL can make up to 300 quarts of food preparation.
SAFETY FEATURES
· Safety on Control Switches:
This safety mechanism prevents any unintentional starting of the Immersion Blender. Two buttons must be pressed to start the Immersion Blender. See section “ON OPERATING THE IMMERSION BLENDER” (page 6).
· Safeties on motor thermal protection: If the machine is overused, the thermal protection will stop the unit. In this case, wait for the unit to cool down (a period of up to 30 minutes) before restarting and proceed to the steps of “OPERATING THE IMMERSION BLENDER” (page 6).
· No volt release safety (Supply failure):
if there is a power failure or the machine is unplugged, the Immersion Blender will not restart by itself. See section “ON OPERATING THE IMMERSION BLENDER” (page 6).
· Safeties on motor overload protection:
If there is an obstruction in the container (a spoon or ustensil) or the machine is overused and becomes hot, the unit will stop. This stop indicates that the preparation is too thick or is not adapted for a Immersion Blender. To restart the machine, see section “ON OPERATING THE IMMERSION BLENDER” (page 6).
03/11/2022 5
INTRODUCTION TO YOUR NEW IMMERSION BLENDER
Robot-Coupe has developed a complete line of Immersion Blenders. The features of each are described in the table below.
Models
MP 350 Turbo MP 350 Turbo V.V. MP 450 Turbo MP 450 Turbo V.V. MP 550 Turbo MP 600 Turbo MP 800 Turbo MP 350 Turbo Combi MP 450 Turbo Combi MP 450 Turbo FW MP 450 Turbo FW XL
Variable Speed
· · · · · · · · · · ·
Blade attachment
· · · · · · · · · · ·
Whisk attachment
· · · · · · · · · · ·
Mixing tool attachment
· · · · · · · · · · ·
The Robot-Coupe Immersion Blenders perform a host of culinary feats. The blade attachment will allow you to make soups, vegetable purees and pulps while the whisk attachment is ideal for making pancake batter, mayonnaise, beaten egg whites, chocolate mousse, butter sauces, whipped cream or smooth fromage frais.
The mixing tool attachment (FW XL) is used to blend and homogenise very light preparations such as purees and soups made with dehydrated flakes and sauce + spice mixes.
It is not designed to make pasta or thick purees. The variable speed function will enable you to adjust the speed to suit each preparation and to start the processing at a lower speed in order to reduce splashing.
6 03/11/2022
The Immersion Blender is easily assembled and disassembled for maintenance and cleaning.
OPERATING THE IMMERSION BLENDER
· OPERATION (valid for all models)
The Immersion Blender is equipped with electrical current and temperature overload protection. If the Immersion Blender stops unexpectedly you may try to restart it by following steps 3-5 below. If the Immersion Blender does not restart, allow it to cool for a period of up to 30 minutes and the temperature overload will automatically reset. You should then be able to restart following steps 3-5 below.
1. Check that the control
SB
button (CB) is in the VS
BC
released position.
BV
V
2. Connect the cord to
the power supply.
3. Put the tube into the product with the bell completely immersed.
4. Press and hold down the safety button (SB).
5. Press the control button (CB). The Immersion Blender starts working and the green “ON” indicator (V) lights up.
6. Release the safety button (SB).
7. To stop the Immersion Blender, release the control button (CB), the green “ON” indicator (V) goes off.
· CONTINUOUS OPERATION (valid for all models)
8. Follow steps 1-6 above, then: While the control button (CB) is pressed, press the locking button (LB).
9. Release the control button (CB).
SB V
MOTOR
HOUSING
CB LB
10. Release the locking button (LB). The Immersion Blender then starts working by TUBE itself (the green “ON” indicator (V) lights up).
11. To stop the
Immersion Blender, press
and release the control
BELL
button (CB). The green
“ON” indicator (V) goes
off.
· VARIABLE-SPEED OPERATION
Follow steps 1 to 6 above, then change the speed of the motor by turning the button (VS) toward the maximum or minimum as required.
It is advisable to start at a low speed when using the whisk.
Principal of automatic speed regulation: Once you have selected the right speed, allow the Immersion Blender to run on it’s own. The speed will remain the same, even if the consistency of the product changes.
· MASHED POTATOES FUNCTION (MP 350 Turbo Combi, MP 450 Turbo Combi, MP 450 Turbo FW). A self-regulating speed system has been specially developped for pureeing tasks using the whisk.
A white circle marked on the speed variation switch indicates the speed dedicated to mashed potatoes preparation. To reach this speed, turn the knob counterclockwise until it stops and a slight detent is felt. Under load the Immersion Blender will stop and start at one seconds intervals.
· POWER CORD After cleaning the machine, wind the cord around the specially designed lugs, without stretching it too much. This will prolong its lifespan.
WORKING POSITION
WA R N I N G
However the Immersion Blender is used, for safe operation, both hands must be positioned on the places described below and always kept as far as possible from sharp, rotating parts.
To make our machines more ergonomic, safer to use and easier to handle, we recommend using the “removable handle” attachment.
The handle can be used on all Immersions Blenders in the Large range including the Combi models (except the MP 800 Turbo).
We recommend holding the Immersion Blender by both the main handle and the removable handle. We also recommend tilting the Immersion Blender slightly, making sure that the bell does not come into contact with the bottom of the recipient.
Installing the handle:
– Unplug the Immersion Blender first.
– Slide the removable handle onto the motor base from underneath the Immersion Blender (1), making sure that:
– the word “TOP” is facing upwards (1).
– Turn the stainless steel adjusting screw anticlockwise (1) until the handle is slightly above the aluminium housing as indicated in step (2).
N.B. During assembly, check that the elastomer seal on the removable handle is always aligned with the rest of the handle (1).
– Then push the handle downwards until it sits on top of the aluminium housing (3).
– Lock the handle into its final position by turning the adjusting screw clockwise (4) until fully tightened.
1
2
3
4
· BLADE FUNCTION For your safety, it is forbidden to let the machine work alone during continuous operation of the machine. It is necessary to keep holding the handle with your hands in order to stop continuous operation quickly in case of emergency. The use of any pan support is also forbidden. 1) For safe, efficient operation, the Immersion Blender must be held by the handle, as indicated in the drawing opposite.
1/3 2/3
03/11/2022 7
2) As shown in the drawing
opposite, the Immersion
Blender foot can also be
placed in contact with the
edge of the pan making sure
it is held at an angle and
that the bell is not in contact 1/3
with the bottom of the pan.
2/3
MP 800 Turbo.
An handle which will help you to have a good grip and facilitate the moving of the machine.
3) For optimum efficiency two thirds of the tube should be immersed in the product.
4) Always make sure that the bell is completely immersed to avoid splashing and that the ventilation openings in the motor housing do not come into contact with any liquid !
8 03/11/2022
· WHISK FUNCTION
For greater efficiency, it is recommended holding the Immersion Blender by the handle and the motor base, as shown in the appended drawing.
The hand on the motor base supports the Immersion Blender.
You can also hold the appliance by the handle with one hand, leaving the other hand free to hold the bowl, if necessary.
While processing we recommend that you move the whisk around in the bowl, in order to ensure that the mixture is completely homogeneous.
We strongly advise you to keep the whisk from touching the sides of the bowl.
For maximum efficiency, at least one-fifth of the whisk length should be immersed. We also strongly advise you to start the processing at a low speed. Handle conveniently located on the mixing tool for a better grip.
ASSEMBLY & DISASSEMBLY
· BLADE FUNCTION
Attaching the tube to the motor unit, (Except for MP 350 Turbo, MP 450 Turbo, MP 550 Turbo, MP 600 Turbo). – Unplug the Immersion Blender. – Unplug the machine then, align the flat side of A
the conical part C of the tube with catch B in the aluminum casing. – Insert the narrow portion of conical part C of the tube into the aluminum casing. – Turn the tube in the direction of the arrow (see figure) until it is snugly in place.
Removing the tube from the casing – Unplug the Immersion Blender. – Turn the tube in the opposite direction of that used
to attach it. – When it will not go any further, remove the tube
from the conical part. Attaching the bell to the tube
TURN TO
ATTACH BELL
– Unplug the Immersion Blender. – Align the flat side of A the conical part of the tube
with catch B on the inside of the bell. – Insert the conical part C into the bell. With the
washer touching the tube seal D, turn the bell in the direction of the arrow (See figure) to lock the bell lug E and tube lug F snugly together. Disassembling the bell from the tube
– Unplug the Immersion Blender. – Turn the bell in the direction of the arrow 1 (see
next figure) to separate the bell lug E from the tube lug F. – Remove the bell.
Removing the blades Unplug the machine. Turn the bell in the direction of the arrow 1 (see next figure) to separate the bell E from the foot lug F. Remove the bell. To safely remove the sharp blades, hold with the provided blade locking tool. Using the blade disassembling tool, unscrew the male drive coupling. As the drive coupling is unscrewed disengage the blade for easy cleaning.
BLADE LOCKING
BLADES WITH WATERTIGHT SEALS
BELL
· WHISK FUNCTION (MP 350 Turbo Combi, MP 450 Turbo Combi, MP 450 Turbo FW)
Attaching the whisk gearbox to the motor unit
– Unplug the Immersion Blender.
– Align the flat side A of the conical part C of the whisk gearbox with the catch B on the inside of the aluminum casing.
– Insert the conical part C of the whisk gearbox into the aluminum casing.
– Turn the whisk gearbox in the direction of the arrow (see figure) until it is snugly locked into place.
Removing the gearbox
– Unplug the Immersion Blender. – Turn the whisk gearbox in the opposite direction
from that used to attach it. – When it will go no further, remove the whisk
gearbox from the aluminum casing.
TURN TO REMOVE BELL
MALE DRIVING COUPLING BLADE REMOVAL
03/11/2022 9
Fitting the whisk into the whisk gearbox
Removing the whisk from the whisk gearbox
While griping the ejector A in one hand and the holder B in the other, pull the ejector in the direction of the arrow.
Once the mixing tool has been attached to the housing, simply insert the latter into the motor unit, turning it in an anticlockwise direction. Detaching the mixing tool from its housing:
MIXING TOOL
HOUSING
– Grasp the holder in one hand.
– With the other hand, take the first whisk and insert the shaft A into the bore B of the whisk gearbox drive shaft. Make sure the drive lugs D are properly aligned with the notches.
– As you push the whisk into the holder drive shaft C, rotate it slightly in order to slide the drive lugs into the notches D of the drive shaft C, thereby locking the whisk into place inside the shaft.
– To check that the whisk is properly fixed inside the shaft C, gently pull the metal wires.
– Repeat this procedure with the second whisk. If you cannot push it in properly, remove it, rotate it 90° and start again.
10 03/11/2022
Removing the ejector Hold the whisk by the wires B Bin one hand. With the other hand, pull the ejector A in the direction of the arrow (see figure).
· MIXING TOOL FUNCTION (MP 450 Turbo FW XL)
Attaching the mixing tool to the mixing tool housing:
MIXING TOOL
HOUSING
MIXING TOOL
Line the flat side of the mixing tool B up with the flat side of the housing A.
MIXING TOOL
To release the mixing tool from its housing, simply press the button C. All that then remains to be done is to remove the housing from the motor unit.
CLEANING
WARNING
· Always unplug the Immersion Blender before cleaning it!
· Always dilute bleach according to the instructions on the label
· Never run the motor assembly through a dish machine.
· The type and concentration of the sanitation agent must comply with 21 CFR 178 1010 regulations.
· Clean according to local health department regulations.
· MOTOR HOUSING
The Immersion Blender must be clean through all stages of production. Clean between each job using a detergent or disinfectant. Dilute the detergent/ disinfectant following the instructions normally specified on it’s packaging container. Use a cloth lightly dampened (not dripping) with the cleaning solution.
Do not allow liquid to come into contact with the electrical components contained within the housing. Be careful when cleaning around vents do not allow liquid to drip or seep into the housing. Use a cloth lightly dampened (not dripping) with water to remove detergent/ disinfectant then dry using a clean cloth. After using the Immersion Blender in a hot mixture, cool the bottom of the tube in cold water before disassembling the bell from the tube. Clean immediately after use to prevent product from sticking to surfaces.
WARNING
Never immerse motor housing and/or handle in liquid! The housing contains the electrical components and is not sealed against liquid. Contact with liquid can cause damage to the Immersion Blender and serious injury to the operator.
· TUBE AND BELL
There are two ways to proceed:
· Simple cleaning procedure after each different use
– Submerge the tube and bell in water and run for a few seconds to clean.
– Unplug the power cord.
Complete cleaning procedure on a daily basis – Unplug the Immersion Blender and rinse the bell
under a water tap. – Remove the bell from the tube, then remove the
blade (wear cutting gloves) ! Be careful to avoid damaging the surface of the blade shaft and the watertight seals. – Always dilute the detergent/disinfectant (see above). – Thoroughly dry all parts before reassembling.
· BLADE
The blade can be removed from the bell for thorough cleaning. After cleaning, dry all the parts carefully to prevent oxidation.
· ALUMINUM
Use soft-metal-safe cleaning agents!
· PLASTIC
Be careful, many cleaning agents are corrosive and are not safe for use on plastics! Do not use strong alkaline detergent (having a high concentration of soda or ammonia).
· WHISK GEARBOX
Never immerse the whisk gearbox in water. Clean it with a cloth lightly dampened (not dripping). Never run the whisk gearbox through a dishwasher.
· WHISKS The whisks can be cleaned either by hand or in a dishwasher. To ensure effective cleaning, always remove the whisk ejector.
· MIXING TOOL HOUSING Never immerse the mixing tool housing in water or put it in the dishwasher. Instead, clean it with a slightly damp cloth.
· MIXING TOOL The mixing tool can be washed either by hand or in the dishwasher. You can also clean it with a slightly damp cloth.
MAINTENANCE
· BLADE The performance of the cut essentially depends on the state of your blades and their wear. The blades are subject to wear and as such need to be replaced from time to time to ensure the consistent quality of the end product. You are also advised to change, at the same time, the washer and the watertight seals. A blade service kit is available.
· WHISKS The performance of the whisks depends on the condition of the wires. The metal wires may become worn over time. In order to ensure optimum performance, they will need to be replaced. Do not use a defective or damaged whisk!
03/11/2022 11
· POWER CORD: For your safety, make sure the power cord is always in good condition. The cord is subjected to considerable wear and tear, and must be replaced if it is damaged in any way (cuts, burns, etc.). Procedure for replacing the power cord: 1) Use the dismantling tool supplied with the new
replacement cord. 2) Press the push button (see photo) and pull on the
cord without releasing the dismantling tool. 1
2
1ST STAGE
2ND STAGE
Connect the electrical plug to the power supply.
Make sure the plug is pushed in far enough (two stages). If it is not, the control buttons will not work.
· TUBE SEAL In order to maintain a watertight seal between the tube and bell, inspect the seal for wear and replace it if necessary.
· SEAL RING The seal ring can be lubricated using a suitable food grade grease. In order to maintain a watertight seal, check the seal ring for wear and replace it if necessary. The seal ring is easy to replace so we strongly recommend always checking it is in good repair.
2) Cartridge mounting:
Direct the ears of cartridge B in order to be aligned with the groove of the bell A.
Push the cartridge with the hand in the direction of arrow, then clip on into the bell thanks to the knife dismantling tool.
3) Installing the new cord: Connect the “Easy-Plug” to the motor housing. Before doing so, make sure the electrical plug is not connected to the power supply.
12 03/11/2022
· CARTRIDGE
You need to change the cartridge: – If liquid starts seeping into the foot, – If there is any play in the blade.
1) Cartridge dismantling: Position the knife dismantling tool C on the cartridge B. Remove the cartridge from its place by knocking D on the knife dismantling tool C with a plastic mallet.
TROUBLE SHOOTING
· THE IMMERSION BLENDER DOES NOT START.
1. Did you follow the previous operating instructions? See section “OPERATING THE IMMERSION BLENDER” page 6.
2. If the green “ON” indicator does not light up when the control button (CB) is pressed, check the following:
FLASH
MP 600/MP 800
– The network voltage
– Correct connection of the cable to the wall plug.
GREEN “ON”
INDICATOR
– Correct attachment of the cord to the handle (see page 12).
– The state of repair of the cord (any cut wires) If this is the case, see replacement procedure on page 12.
3. Is the machine too hot ? (the Immersion Blender is not operating but the green “ON” indicator up when the control button (CB) is pressed). Allow the Immersion Blender to cool. Then retry.
4. Pull the plug and try another outlet.
5. Check the GFI trip indicator on your outlet. Check the circuit breaker.
6. Call local Robot Coupe authorized service agency.
· THE IMMERSION BLENDER STOPS DURING (WHILE) PROCESSING.
See the section “OPERATING THE IMMERSION BLENDER” page 6.
– The first paragraph describes the overload protection. It may be necessary to allow the machine to cool for up to 30 minutes before restarting.
If the reason is unknown or if the green “ON” indicator comes on when the control button is pressed but the motor does not start:
– Release the control button (CB). – Unplug the Immersion Blender.
– Are the blades free to rotate in the bell?
– Is the drive shaft free to rotate? To check this, unplug the Immersion Blender, remove the bell and test the rotation of the end of the drive shaft manually.
Check the condition of the plug and the power cord.
· THE IMMERSION BLENDER STARTS TO SMELL HOT OR SMOKE
– Turn the Immersion Blender off and unplug it. – Call your local authorized service agency.
· THE MACHINE TRIPS THE GFI (Ground fault Interrupt) OUTLET
The motor or controls are wet or damaged. Do not attempt to use the Immersion Blender until it has been repaired by qualified service persons.
· OVERLOAD WARNING LIGHT (MP 600 Turbo and MP 800 Turbo)
In case of overload or use of the Immersion Blender in a too sticky preparation, the intensity warning flashes for 5 seconds to inform you that the motor will stop shortly.
FLASH
This stop indicates that the preparation in process is too thick or can not be made with a Immersion Blender.
In this case, you can still restart your Immersion Blender. However, your machine will stop again if the consistency of the preparation is not modified.
WARNING
THE BLADES ARE SHARP! It is recommended that cutting gloves be worn when handling the blades. Handle and store the blades with safety in mind. Never try to override or defeat the purpose of the safety mechanisms! Never put anything (utensils etc.) but food material near the blades on the Immersion Blender! Never overload the Immersion Blender! Never turn the Immersion Blender on, unless the bell is completely immersed in the product. Always unplug the Immersion Blender before doing any cleaning or maintenance! Unplug the Immersion Blender whenever it is not being used. Plug the Immersion Blender only into a GFI type outlet. Never use extension cords.
SERVICE
See warranty first then; Should your unit require service, check with your distributor to see where local service is available. If not or if you wish your unit to be serviced at the factory, call for return instructions and ship the unit prepaid to our factory address.
Robot Coupe U.S.A., Inc., Service Department 264 South Perkins
Ridgeland, MS 39157 Phone : 800/824-1646 For service in Canada contact the Robot-Coupe USA factory for repair instructions.
03/11/2022 13
ELECTRICAL AND WIRING DIAGRAMS
03/11/2022 41
03/11/2022 43
44 03/11/2022
Réf. : 450 721c – 03/11/2022 – USA
Robot Coupe U.S.A., Inc.,
Phone: 800/824-1646 · 601/898-8411 264 South Perkins St., Ridgeland, MS 39157
e-mail: info@robotcoupeusa.com website: www.robot-coupe.com
Documents / Resources
 | robot coupe MP Series Turbo Immersion Blender [pdf] User Manual MP 350 Turbo, MP 350 Turbo V.V., MP 450 Turbo, MP 450 Turbo V.V., MP 550 Turbo, MP 600 Turbo, MP 800 Turbo, MP Series Turbo Immersion Blender, Turbo Immersion Blender, Immersion Blender, Blender |