Categories: RLE Technologies

RLE Technologies WiNG-CO2 Wireless Sensors User Guide

RLE Technologies WiNG-CO2 Wireless Sensors

Supplies Required

  • WiNG-CO2 Sensor
  • Small flathead screwdriver

Modify the CO2 Measurement Interval

The default CO2 measurement interval of the WiNG-CO2 is 2 minutes. This interval can be changed to values from 1 to 15 minutes. Interval modifications will alter the battery life of the device; a shorter interval will reduce the battery life of the sensor.
If you’d like to adjust the measurement interval of the WiNG-CO2 sensor, you can do so after you’ve completed the initial configuration procedure as detailed in the WiNG-CO2 Quick Start Guide.

  1. After you have completed the initial configuration procedure – compensate or altitude, set the auto-zero function, and configure the zero point in fresh air – you can adjust the measurement interval. This should be done at the same time as the initial configuration, and not separately. To configure the measurement interval:
    1. Hold the push button on the top of the sensor. DO NOT release the button. The LED will turn white and then it will turn green.
    2. Continue to hold the button for 5 additional seconds after the LED turns green, until the LED flashes cyan 3 times. Release the button.
  2. Note the current position of the rotary switch. It is in the correct position for the altitude setting for this sensor, and once the measurement interval  has been configured you’ll need to return the rotary switch to this altitude setting.
  3. Set the rotary switch to the desired number of minutes for the CO2 measurement interval.
  4. Press the button to confirm the change. The LED will flash green.
  5. If the rotary switch has changed from the previous position (the altitude configuration setting) then the LED will flash red until the previous position is restored. Reset the rotary switch to the previous position. A green LED indicates that configuration has completed successfully and that the sensor has returned to the main application mode.
Rotary Switch Setting CO2 Measurement Interval
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
A 10
B 11
C 12
D 13
E 14
F 15

WiNG-CO2 – Measurement Interval Configuration Guide

Thank you for purchasing a WiNG-CO2 wireless sensor. Before you change the measurement interval on your sensor, consult rletech.com to ensure you’re working with the most recent version of documentation available. If you need further assistance, please contact RLE Technologies at support@rletech.com.

Documents / Resources

RLE Technologies WiNG-CO2 Wireless Sensors [pdf] User Guide
WiNG-CO2, Wireless Sensors, WiNG-CO2 Wireless Sensors

References

Share

Recent Posts

pdp gaming NS 500-188 Joy-Con Charging Shuttle for Nintendo Switch User Guide

NS 500-188 Joy-Con Charging Shuttle for Nintendo Switch EACH PANEL 85mm 105mm FOR NINTENDO SWITCH…

12 mins ago

DRIJA DOLCETTO 33 Vinera Recessed Compressor User Manual

DOLCETTO 33 Vinera Recessed Compressor Manual de Usuario VINERA CON COMPRESOR PARA EMPOTRAR | DOLCETTO…

12 mins ago

VAULT Rhome Sputnik Chandelier Instructions

Rhome Sputnik Chandelier

13 mins ago

OtterBox Defender Series Tablet Instruction Manual

Defender Series Tablet Defender Series Installation Instructions 1 Release corners and remove shield stand. 2…

13 mins ago

CLAGE M3..7-O E-Mini Instant Water Heater Instruction Manual

M3..7-O E-Mini Instant Water Heater Gebrauchs- und Montageanleitung Operating and installation instructions E-Kleindurchlauferhitzer M 3..7-O…

18 mins ago

SIRMAN Sansone 25 Pasta Sheeter User Manual

Sansone 25 Pasta Sheeter INSTRUCTION, USER AND MAINTENANCE MANUAL ed. 10/2019 - ver. 001 Pasta…

18 mins ago