RIB SUN 2CH Remote Control
The transmitter is supplied with a 12 Vdc battery type 23A.
SUN has a POWER SAVER feature that prevents the battery from discharging accidentally. If the button is pressed and held for more than 8 s, the transmitter switches off automatically and will reactivate thereafter in response to a new command.
A led lights up whenever the control is activated.
If led flashes, this means that battery must be replaced as soon as possible. If the led doesn’t lights, the battery is empty and the command is not executed.
CREATING A CODE IN THE TRANSMITTER
Each SUN has a code programmed in factory.
It is possible to manually change the code with following procedure:
- Press and immediately release the button A on the transmitter.
- You have 2 s to press and hold for 5 s the button B => The Led on the SUN will turn on for 5 s and then will go off. Wait for the led light to go off before memorizing a new code.
- You now have 10 s to manually create the code. To do that you must press 10 times the buttons A (DIP OFF*) or B (DIP ON*), depending on the code one wants to create. At the end, the led light stays on for 3 s to confirm the correct memorization of the new code.
* DIP ON or OFF: correspond to the same position of the Dip-switches available in some of the old generation radio receiver and transmitters.
PROGRAMMING
See the RIB instructions of receivers or CRX scontrol panels.
OPERATING TEMPERATURE
-20 ÷ +50 °C
ATTENTION
- READ AND FOLLOW ALL THE INSTRUCTIONS.
- Keep the transmitter out of the reach of children.
- Command pulses must be given from sites, where You can see the gate.
- Use transmitters only if You can see the gate.
- This instruction booklet is for specialized personnel only.
R.I.B. accepts no responsibility for any damage caused by the safety regulations at present in force not being observed during installation.
The battery polarity and the model are indicated in the battery compartment. We remind you that batteries must be smaltited in compliance with current norms.
In case of wreckage of the transmitter we remind you to remove the battery and dispose according to current norms.
DECLARATION OF COMPLIANCE
- Apparatus model: SUN 2CH
- Object of the declaration:
The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:
EN 300 220-2 V3.2.1
EN 301 489-1 V2.1.1
EN 301 489-3 V2.1.1
EN 60950-1:2014
Specifications
- Product Name: SUN 2CH
- Frequency: 433 MHz
- Model Number: ACG6052
- Battery Type: 12 Vdc, 23A
- Origin: Made in Italy
Transmitter Operation
The transmitter is supplied with a 12 Vdc battery type 23A. It switches off automatically after activation and will reactivate upon a new impulse.
Battery Replacement
If the LED flashes, it indicates a low battery, and you should replace it promptly to ensure proper functioning.
Programming Receivers
Refer to the specific receiver or control panel manuals for programming instructions.
FAQ
Q: What should I do if the LED doesn't light up after pressing the button?
Q: How can I confirm the successful creation of a new code in the transmitter?
Documents / Resources
 | SUN 2CH Remote Control |
Bonjour,
Je dispose déjà de plusieurs télécommandes de ce type (RIB SUN 2CH). J’en ai acheté deux autres pour avoir des doubles mais je ne trouve pas de méthode pour les programmer à partir de celles que j’avais en ma possession.
Pouvez-vous me donner le moyen de copier les codes depuis les anciennes aux nouvelles ?
Merci de votre réponse.
Cordialement.
Je dispose déjà de plusieurs télécommandes de ce type (RIB SUN 2CH). J'en ai acheté deux autres pour avoir des doubles mais je ne trouve pas de méthode pour les programmer à partir de celles que j'avais en ma possession.
Pouvez-vous me donner le moyen de copier les codes depuis les anciennes aux nouvelles ?
Merci de votre réponse.
Cordialement.
How do I copy codes from an old RIB SUN 2CH remote control to a new one?
The RIB SUN 2CH remote control does not support direct cloning or copying from one remote to another. Instead, each remote control must have its code manually configured or programmed directly into the receiver.
To manually set a specific code on your new remote control, follow these steps:
Après avoir configuré le code sur la télécommande, vous devez l'enregistrer sur votre récepteur en suivant le manuel de votre récepteur ou de votre coffret électronique CRX RIB.
Read the full Q&A page