FP2043 SERIES
QUICK START GUIDE
Product Code
FP2043T-V2: 4.3″, 480 x 272 pixels, WQVGA color TFT with 4-wire analog resistive touch screen with 2 serial ports#, one USB Type C, one USB Host port.
FP2043TN-V2: 4.3″, 480 x 272 pixels, WQVGA color TFT with 4-wire analog resistive touch screen with 2 serial ports#, one USB Type C port, one USB Host port, 1 Ethernet port.
FP2043T-E: 4.3″, 480 x 272 pixels, WQVGA color TFT with 4-wire analog resistive touch screen with 2 serial ports#, one USB Type C, one USB Host port. It supports 1 expansion module.
FP2043TN-E: 4.3″, 480 x 272 pixels, WQVGA color TFT with 4-wire analog resistive touch screen with 2 serial ports#, one USB Type C port, one USB Host port, 1 Ethernet port. It supports 1 expansion module.
[# Note: For more information about #, please refer specifications section.]GETTING STARTED
User should follow the given sequence to configure and use any FlexiPanels series unit:
- Install FlexiSoft Software.
- Create a PZM application using FlexiSoft software.
- Connect programming cable.
- Download Firmware i.e. driver for the HMI.
- Download application.
- Now FP unit is ready to use in the system.
For More Information, Visit
https://www.renuelectronics.com
SPECIFICATIONS
| Power (Base) | 24VDC(+20%,) @130mA, 3.12W (T-V2 module) 24VDC (+20%,) @150mA, 3.6W (TN-V2 module) |
| Power (With Expansion) | 24VDC(+20%) @160mA, 3.84W (T-E module) 24VDC (+20%,) @180mA, 4.32W (TN-E module) |
| Display | 4.3″, 480 x 272 pixels, WQVGA color TFT with 4-wire analog resistive touch screen |
| LEDs | 1 |
| RAM | 16MB max. |
| User Application | 8MB |
| FLASH | 16MB |
| Ladder Memory | 2MB |
| Alarm Memory | 1350 Alarms |
| Retentive Memory | 8000Words |
| Data Log | 4MB |
| Keep Memory Registers | 1000Words |
| Panel Cutout | 80(H) x 111(W)mm |
| Dimensions | 89(H) x 120(W) x 31.5(D)mm |
| Weight | Approx. 200gm |
| Communication | |
| Serial Port | (1 x RS232 ) + (1 x RS485# ) |
| USB Ports | 1 USB Type C & 1 USB Host 1 |
| Ethernet | Ethernet Port |
| SD Card | Micro SD [High Capacity (4GB to 32GB)]
Speed Class:  [While inserting and removing SD card, please make sure to TURNOFF the power to the unit.] |
| Expansion* | Supports 1 Expansion slot |
| Environment & Approvals | |
| Operating Temperature | 0°C to 50°C |
| Storage Temperature | -30°C to 85°C |
| Humidity | 10 to 90% (Noncondensing) |
| Shock | 25g, 11ms, 6 shocks per axis, Total 18 shocks (X, Y, Z) |
| Vibration | 5~150Hz, 3g peak, (X, Y, Z) IP66 |
| Protection | Front panel-IP66, Rare panel-IP20 |
| APPROVALS | CE, UL (Class 1 DIV 2), UKCA, REACH & RoHS |
(REPL Part# EC-Y-FP)
PANEL CUTOUT DIMENSIONS
FRONT VIEW
RIGHT SIDE VIEW TOP VIEW
PANEL CUTOUT DIMENSIONS
Pautout Dimensions: 80.00(H) x 111.00(W)mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 2
Tighten the mounting screws evenly to a torque between 0.4N/m to maintain water and dust resistance.
Earthing
The optimum method for Earthing electronic equipment is to earth it separately from other high-power systems, to earth more than one unit of electronic equipment with a single-point earth. The Earthing marked terminal (see below) is provided on the unit.
COMMUNICATION
This section provides information regarding communication interfaces supported by this product.
Serial Port
1 Physical Port : COM1-RS232, COM2-RS485
| Pin number | Signal |
| 1 | TX+(RS422/RS485) |
| 2 | TXD(RS232) |
| 3 | RXD(RS232) |
| 4 | RX+(RS422/RS485) |
| 5 | GND |
| 6 | NC |
| 7 | NC |
| 8 | TX-(RS422/RS485) |
Y Type Cable
Special “Y” cable for FP unit (two communication levels on one port).
- Connect to Panel (HMI)
- Cable length 9″
- Cable length 6″
- Connect to Third Party devices
(DB9 Male Connector) (RS485 Female Connector) (RS232 Female Connector)
| Pin number | Signal | Pin number(RS485) | |
| 1 | TX+ |  | 1 |
| 2 | TXD | 2 | |
| 3 | RXD | 3 | |
| 4 | RX+ | | 4 |
| 5 | SG | | 5 |
| 6 | NC | 6 | |
| 7 | NC | 7 | |
| 8 | TX- | | 8 |
| 9 | RX- | | 9 |
| Pin number | Signal | Pin number(RS232) | |
| 1 | TX+ | 1 | |
| 2 | TXD |  | 2 |
| 3 | RXD | | 3 |
| 4 | RX+ | 4 | |
| 5 | SG | | 5 |
| 6 | NC | 6 | |
| 7 | NC | 7 | |
| 8 | TX- | 8 | |
| 9 | RX- | 9 |
Cable Diagram :
RS232 pinout
RS232 MALE RS232 FEMALE
| Pin number | Signal | Pin number | Signal | |
| 2 | TXD |  | 2 | RXD |
| 3 | RXD | | 3 | TXD |
| 5 | GND | | 5 | GND |
2-wire RS485 pinout
| Signal | Pin number | Signal | |
| A (TX+ / RX+) |  | 1 | TX+ |
| 4 | RX+ | ||
| GND | | 5 | GND and Shield |
| B (TX- / RX-) | | 8 | TX- |
| 9 | RX- |
4-wire RS485 pinout
| Pin number | Signal | Pin number | Signal | |
| YELLOW | TX+ | | 1 | TX+ |
| GREEN | RX+ | | 4 | RX+ |
| BLACK | GND | | 5 | GND and Shield |
| WHITE | TX- | | 8 | TX- |
| BLUE | RX- | | 9 | RX- |
USB Type C Port
- USB Type C, compliant with USB 2.0 specification, self-powered device.
- Connector used: Micro USB Type C Female connector.
| Pin number | Signal |
| 1 | VCC |
| 2 | D- |
| 3 | D+ |
| 4 | NC |
| 5 | GND |
USB Host Port
- USB Host, compliant with USB 2.0 specification.
- USB Host can handle only USB memory stick devices and can source current up to 150mA only.
- Connector used: Standard USB Type a Female connector.
| Pin number | Signal |
| 1 | VCC |
| 2 | D- |
| 3 | D+ |
| 4 | GND |
Ethernet Port
- Fully compliant with IEEE 802.3 / 802.3u standards.
- 10/100 Mbps support.
- Connector used: Standard shielded RJ-45 female jack with in-built speed and link activity indication LEDs.
Default IP Address: 192.168.0.254
Default Subnet Activity Mask: 255.255.255.0
| Pin number | Signal |
| 1 | TX+ |
| 2 | TX- |
| 3 | RX+ |
| 4 | NC |
| 5 | NC |
| 6 | RX- |
| 7 | NC |
| 8 | NC |
REVISION HISTORY
CONTROL DRAWING N v O# CNTL/DWG/FP2043/0318 VER.NO.: 1.00
Hazardous Location Non-Hazardous Location
Class I Division 2 Groups A B C and D
TABLE 1:
| Nonincendive. Equipment | Associated Apparatus | |
| V max (or Ui) | = | Voc or Vt (or Uo) |
| I max (or Ii) | : ≥ | Isc ot It (or Io) |
| Ci + Ccable | : ≥ | Ca (or Co) |
| Li + Lcable | : ≤ | La (or Lo) |
Capacitance and inductance of t≤ wiring from the nonincendive equipment to the associated apparatus shall be calculated and must be included in the system calculations as shown in Table 1
Where the cable capacitance and inductance per foot are not known, the following values shall be used: Caable = 60 pF/ft., Lcable = 0.2 μH/ft
Wiring method must be in accordance with ANSI/NFPA70
WARNING: DO NOT REMOVE OR REPLACE WHILE BE FREE OF IGNITIBLE CONCENTRATIONS OF FLAMMABLE SUBSTANCES.
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous locations only.
WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous.
WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability for Class I, Division 2.
A recommendation for the user to periodically inspect the sealed devices used, for any degradation of properties and replace if degradation is found.
REVISION HISTORY
| Rev. | Description | Date |
| 1.0 | First Draft | 14/08/2020 |
| 1.1 | Added Website Information | 27/08/2020 |
| 1.2 | Updated Communication Information | 07/09/2020 |
| 1.3 | Updated Power supply port position | 06/01/2020 |
| 1.4 | Updated IP rating | 02/06/2021 |
| 1.5 | Replaced USB type from Micro to Type C | 11/10/2021 |
| 1.6 | Added SD card Information | 15/04/2022 |
| 1.7 | Logo updated | 20/09/2022 |
| 1.8 | Specification updated | 09/06/2025 |
RENU Electronics Pvt. Ltd® reserves the right to change or discontinue specifications and features without prior notice.
To view the latest and updated datasheets/manuals, please visit www.renuelectronics.com.
Documents / Resources
 | RENU FP2043 SERIES Analog Resistive Touch Screen [pdf] User Guide FP2043 SERIES Analog Resistive Touch Screen, FP2043 SERIES, Analog Resistive Touch Screen, Resistive Touch Screen, Touch Screen |