RAIGOH 4420 CD Record Able ReWrit Able Unit
CD-Recordable / ReWritable unit
CD-R/RW
E-IDE/ATAPI internal
User’s Manual
MP7040A АТАРІ INTERNAL MODEL CD-R/RW Drive
System environment
This unit can be operated in the system environment explained here.
| System requirements | CPU | 100 MHz (or faster) Pentium (for 4x speed, 166MHz or faster recommended) |
| Memory | Windows 98/95: 32MB or greater. Windows NT Workstation Ver. 4.0: 32MB or greater (64MB or over recommended) | |
| Harddisk | Hard disk with average access time of 19msec or less, and data transfer speed of 1,200KB/sec or greater. 75MB or more free space. (The free space needed for writing depends on the quantity of data.) | |
| Interface | Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) | |
| Drive bay | 5.25-inch half height bay required | |
| Power | +5V/+12V power socket required | |
| Software Required OS | Windows 98/95, Windows NT Workstation Ver. 4.0 (Service Pack 3) or later*1 | |
| CD-R, CD-RW discs | Ricoh, Kao, Mitsubishi Chemical, Taiyo Yuden, Mitsui Toatsu, TDK or Kodak discs are recommend. | |
- Occasionally the CD-R and CD-RW discs written by the CD-R/RW drive cannot be read by other CD drives*2. These unreadable discs should read using the CD-R/RW drive.
- With Windows NT Workstation Ver. 4.0, only usable with Ahead® NERO The disc written using the CD-R/RW drive might not be readable b
- CD-ROMs other than Multi-read compatible (Random UDF compat ible) CD-ROMs.
Multiread compatible (Random UDF compatible) CD-ROMs are:
- CD-ROMs that can read low reflectance
- CD-ROMs that support Packet Write.
Drive functions and settings
Front Panel
| Name | Function |
| Disc tray | This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the CD will be loaded. Don’t use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. |
| Eject button | This is the button used to eject or bring in the disc tray. |
| Volume control | This is used to adjust the output volume of the headphone jack. It can’t be used to adjust the output volume for the audio output connectors on the rear panel. Turn the volume down before turning on the power. Sudden loud noises can damage your hearing. This indicator is not illuminated unless the disk is currently being accessed. |
| Headphone jack | This jack is for connecting headphones or mini-speakers. |
| Drive activity indicator | This indicator lights orange when a disc is loaded into the drive. When the disc is being accessed, it flashes or lights orange. If no CD is loaded, the indicator does not light even when the power is turned on. When an illegal disc is loaded or some hardware trouble occurs, the indicator blinks. |
Rear panel
| Name | Function |
| Power Connector | Connects to the power supply (5- and 12-V DC) of the host computer. Be careful to connect with the proper polarity. Connecting the wrong way may damage the system (and is not guaranteed). |
| IDE Interface Connector | Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. |
| Jumper Connector | This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. |
| Analog Audio Output Connector | Provides output to a sound card (analogue signal). |
| Digital Audio Output Connector | Not used. |
Installing the Drive
Before Installation
Before installing the drive, please note the following points.
- your will need the following:
- A Phillips head screw driver of a suitable size to fit the securing screws for the drive unit.
- The manual for the computer, so you can find out the positions for the IDE controller.
- Turn off all peripheral appliances of the computer, and the computer itself, and disconnect their power cords from the wall sockets.
- Discharge any static electricity by touching the computer covers etc.
- Record the serial number of the drive unit in the box below.
Serial No.
Jumper Set Up
Before installation, set the jumper on the jumper connector on the rear panel. The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When several (up to four) EIDE devices are connected, each must be set in a unique way. Specific knowledge of hardware and software is necessary to install the drive.
We cannot guaranty against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure.
If two peripheral devices with the same settings are both connected to the Primary or to the Secondary EIDE bus, the host computer may fail to run, or may malfunction, so careful attention is necessary.
Specifications
<Drive· MP7040A>
| Type | Internal type (bare drive) | |||
| Interface | Enhanced-IDE (ATAPI) | |||
| Data buffer memory | 2MB | |||
| Data transfer speed | 16.7MB/sec. | |||
| Write/Read speed (Ave) | 20x: 2MB/sec.(Mode1, Mode2 Form1)<Only read>*1 | |||
| 20x: 2.55MB/sec.(Mode2,Form2)<Only read>*1 | ||||
| 8x: 1.2MB/sec. (Mode1, Mode2 Form1) <Only read>*1 | ||||
| 8x: 1.36MB/sec. (Mode2 Form2)<Only read>*1 | ||||
| 4x: 600KB/sec. (Mode1, Mode2 Form1) | ||||
| 4x: 681KB/sec. (Mode2, Form2) | ||||
| 2x: 300KB/sec. (Mode1, Mode2 Form1) | ||||
| 2x: 342KB/sec. (Mode2 Form2) | ||||
| 1x: 150KB/sec. (Mode1, Mode2 Form1) | ||||
| 1x: 171KB/sec. (Mode2 Form2) | ||||
| 1x: 172KB/sec. (CD-DA) | ||||
| Average access time | 120m sec. or less | |||
| Initial processing time | CD-ROM 12 sec. | |||
| CD-R/RW 17 sec | ||||
| Mounting direction | horizontal/vertical(eject button at top when vertical) | |||
| Compatible formats | Format | <Write> | <Read> | <Play> |
| CD-DA | • | • | • | |
| CD-ROM | • | • | ||
| CD-Extra | • | • | • | |
| CD-ROM XA | • | • | • | |
| Photo CD | • | • | ||
| CD-I | • | • | ||
| CD-ROM + CD-DA | • | • | • | |
| Video CD | • | • | • | |
| Loading system | Tray type (automatic loading/eject) | |||
| Power | DC5V, DC12V | |||
| Power consumption | 12w max (normal operation) 6w max (standby) | |||
| Weight | Less than 1.5 Kg. | |||
| Dimensions | 146 × 193 x 41.5 mm (Width, depth, height) | |||
| Reliability | ||||
| Error Rate | 10-12 bits or less | |||
| MTBF | 100,000 hours or greater | |||
| MTTR | Within 30 minutes | |||
| Environmental Conditions | When operating | When not operating | ||
| Temperature | 5°C to 40°C (No air cooling) | -30°C to 65°C | ||
| Humidity | 5% to 90% R.H. (No condensation) | 5% to 95% R.H. (No condensation) | ||
| * Drive speed drops to 8X when reading or overwriting CD-RW discs. | ||||
* Drive speed drops to 8X when reading or overwriting CD-RW discs.
| Environmental Conditions | When operating | When not operating |
| Vibration | 0.035mmpp (10 to 45Hz) | 1 × 9.8 m/s2 (5 to 300Hz) |
| 0.025mmpp (45 to 65Hz) | ||
| 0.2 × 9.8 m/s2 (65 to 150Hz) | ||
| Shock | 2 × 9.8 m/s2 (6m sec. half sine) | 40 ×9.8 m/s2 (11m sec. half sine) |
| Environmental dust | Class 3 million or less (3 million particles of 0.5 micron dust per cubic foot or less) | |
The drive’s appearance and specifications may change without notice.
<Disc>
The above specifications are for Ricoh CD-Rand CD-RW discs
Recommended Discs
- CD-R: Ricoh, Kao, Taiyo Yuden, Mitsubishi Chemical, Mitsui Toatsu, TDK, and Kodak discs
- CD-RW: Ricoh, Kao, Mitsubish.i Chemical discs
This drive cannot be used with 80 mm CDs
Parts No. R6730807
Copyright RICOH Co. Ltd. 1998.All rights reserved.
Documents / Resources
 | RAIGOH 4420 CD Record Able ReWrit Able Unit [pdf] User Manual mp-7040a, 4420, 4420 CD Record Able ReWrit Able Unit, 4420, CD Record Able ReWrit Able Unit, Able ReWrit Able Unit, Able Unit, Unit |
