RAIDON PC04M-41 Quick Setup

Product Diagrams and Package Contents
Front View

- A Disk LED Indicator
- B Disk Tray Handle
- C Disk Tray Ejection Button
Package Contents
- PC04M-41 unit x1
- Quick Installation Guide
- Standard Bracket x1
- Low-Profile Bracket x1
- Screws & TRAY unlock Keys
Please Note:
- Check the product and all included accessories for defects or missing parts. If you encounter any issues, contact your product supplier.
- For additional information, resources, and downloads, please visit the RAIDON official website at www.RaidonTek.com
LED Status Guide
| Status | Disk LED Status |
|---|---|
| Disk idle | Blue light always On (Note 1) |
| Data accessing | Blue light flashing (Note 2) |
Note 1: Based on the SSD design, for some SSDs, the LED will not light up when it is idle.
Note 2: Based on the SSD design, for some SSDs, the LED will not flash when it is accessing data.
Hardware Installation Guide
Follow these steps to install the PC04M-41:
- Install the PC04M-41
- Insert the PC04M-41 into the PCI Express slot on your motherboard.
- Unlock Disk Tray
- Use the included key, press the tray ejection button to the right, and pull the tray out.

- Use the included key, press the tray ejection button to the right, and pull the tray out.
- Open the Top Cover
- Open the top cover of the case.

- Open the top cover of the case.
- Install M.2 NVMe SSD
- Insert an M.2 NVMe SSD and secure it with the latch.

- Insert an M.2 NVMe SSD and secure it with the latch.
- Put the Top Cover Back
- Close and secure the top cover back onto the case.
- Insert Disk Tray
- Close the handle and slide the tray back into the unit.

- Close the handle and slide the tray back into the unit.
- Power On
- Turn on the system; the operating system should automatically detect the disk.
- Format Disk
- Follow the OS prompts to format the disk if necessary.
How to Adjust the Latch Position
Press the latch and rotate it 90 degrees to remove it. After moving it to the appropriate position, reverse the operation to secure the latch.
How to Change the Bracket
By releasing the screws, you can remove the original bracket, replace it with the desired bracket, and then re-tighten the screws.

Precautions Prior to Use
- Ground Yourself – Safely discharge static electricity by grounding yourself before handling components.
- Unplug Power – Power off and unplug the computer before installation.
- Use a Static-Free Surface – Avoid working on carpets or conductive materials.
- Read Instructions – Review all steps thoroughly before proceeding.
Thank you for choosing RAIDON products!
Please note that the information in this manual was accurate at the time of publication, but product specifications may have changed prior to shipping. For the latest specifications and updates, visit www.RaidonTek.com or contact your sales representative.
For any inquiries about RAIDON products, or to receive the latest product manuals or firmware updates, please email us at: supporting@raidontek.com.
RAIDON is a brand under RAIDON TECHNOLOGY, INC. All content in this manual is copyrighted by RAIDON Technology, Inc.
Troubleshooting
- If the disk LED behavior doesn’t match expected states: LED idle and flashing indications may vary by SSD design; for some SSDs the LED may not light up when idle and may not flash when accessing data.
- If you have missing parts or defects: check the product and all included accessories; if you encounter issues, contact your product supplier.
- If the system doesn’t detect the disk after installation: confirm the installation sequence (tray unlocked, top cover opened/closed correctly, M.2 NVMe SSD inserted and latched, disk tray slid fully back in) and ensure the system is powered on before checking OS detection.
Documents / Resources
![]() | PC04M-41 Quick Setup Guide |
References
- User Manualmanual.tools
