QYTOYS QYSC-S QY Smart Cube

Thank you for choosing Qiyi Smart Cube Welcome to the era of smart cubing!

Read before use

1. This product has built-in sensors to identify and track the dynamics of the cube. The positions of each face of the cube are fixed, so please DO NOT EXCHANGE THE POSITION OF THE CUBE’S CENTER COVER
2. After waking up, a white face red light that stays on for 4 seconds or a battery level below 10% indicates that the battery is about to run out. To ensure performance, please replace the battery in a timely manner.
3. When replacing the battery, please install each center core in the order printed.
4. During the battery replacement process, be careful not to damage the center core end conductive device.
   • Please read carefully and keep it properly before using the product

Quick Start Guide

Scan the QR code to watch the video tutorial

Product Configuration

Basic Parameters

Based on data from the One-think Technology Lab, actual battery life depends on usage.

APP Download

1. Scan the QR code to download the APP (recommended).
2. For iPhone users, you can search for “Smart Player” in the APP Store to download and install the APP. For Android users, you can search for “Smart Player” in Google Play to download and install the APP.
   • The Apple logo and App Store are trademarks registered by Apple Inc. in the United States and other countries and regions.
   • The Google Play logo is a registered trademark of Google Inc.

Connect the cube

1. Log in to your Smart Player account
   • New users do not need to register, and can directly use their mobile phone number or email to receive a verification code to log in.
2. Wake up the cube: turn any side of the cube and see the red light flashing on the white side for 4 seconds to wake up the cube.
3. Click the “Connect Cube” button in the app and follow the prompts to connect Ensure that the Bluetooth function and location service of the mobile phone have been turned on and authorized for use.

Cube Setting

1. Open the center cover and turn the adjusting piece counterclockwise with your fingers to change the axis distance of the cube
   • The number inside the circular hole of the adjusting piece represents the axis distance, the larger the number, the tighter the cube. There are 7 settings.
2. If you want to obtain stronger elasticity, you need to replace the spare spring
   1. Remove the cube edge and corner pieces.
   2. Press and rotate it by 90 degrees to remove the fixture.
   3. Use a tool to pry off the elastic piece in the center.
   4. Replace the spring and buckle the elastic piece.
   5. Install the adjusting and fixing parts.
   6. Install the cube.

• WARNING: Contains button or coin cell battery. Hazardous if swallowed-see instructions
• WARNING: This product contains a Button or Coin Cell
• Battery. A swallowed Button or Coin Cell Battery can cause internal chemical burns in as little as two hours and lead to death. Dispose of used batteries immediately.
• Keep new and used batteries away from children. If you think batteries might have been swallowed or placed inside any of the body, seek immediate medical attention.

Please note

• Ensure that the Bluetooth function and location service of the mobile phone have been turned on and authorized for use.
• After the cube is connected to the app, if there is no operation after 10 minutes, the cube will automatically disconnect from Bluetooth and enter a sleep state.
• If the cube has been bound to an account, it needs to be reset locally before it can be bound and connected to another account.
• Reset method: Turn the white face of the cube continuously for 5 cycles (20 steps), and the white face indicator light flashes for 4 seconds and remains on for 4 seconds, indicating a successful reset.
• In most cases, using the original spring with 7 different axis distances can meet the needs of most cubers. It is recommended that only users with strong manual skills try to replace the spring.
• If the white face red light is constantly on when waking up, it means that the battery needs to be replaced.
• Please follow the printed color sequence when replacing the battery, otherwise it may result in the inability to solve the cube.
• The Smart Cube is a precision electronic product. When replacing the battery, be sure not to damage the conductive device at the end of the central shaft, as this may result in product damage
• This product cannot be subjected to shock, water, or placed in an environment above 60°C
• This product contains small parts, please do not use it for children under 3 years
• Please use the product strictly under the instructions to avoid equipment damage or personal injury due to improper operation.
• Please replace both batteries at the same time to avoid mixing old and new batteries.

Battery replacement

This step must be performed by an adult

After waking up, a white face with a red light constantly on for 4 seconds or a battery level below 10% indicates that the battery is about to run out. To ensure performance, please replace the battery in a timely manner.
The replacement steps are as follows:

1. Disassemble the entire cube, remove the ball core, and use a small screwdriver to unscrew the 4 screws on the ball shell;
   • Scan the QR code to watch the video tutorial
2. Replace the two CR1632 batteries, noting that the positive and negative electrodes are: the two negative electrodes are facing the “negative” symbols on the bottom and top surfaces, and the two positive electrodes are in direct contact;
   1. Step1: Disassemble the ball core
   2. Step 2: Replace the battery
3. Reinstall the circuit board and six central axes;
   1. Step1: Install the circuit board back (note: there are connecting buckles on the circuit board and the ball bearing base that require orientation).
   2. Step 2: Install the central axe back in the order of the printed colors on the circuit board.
4. Screw in the screws and assemble the entire cube.

Troubleshooting

1. APP cannot detect the cube?
   • Please confirm that the power of the cube is sufficient.
   • Please confirm that the cube is in the awake state. When not connected to the app, the awakened cube will automatically enter the sleep state after 60 seconds.
   • Please confirm that the Bluetooth function and location service of the phone has been turned on and authorized for use.
   • If the cube is connected to other devices, it needs to be disconnected before it can be detected by another device.
   • The cube needs to be reset locally (turning the white face 5 times in a row, or 20 steps) before it can be detected and connected by the new account.
2. The status of the cube is not synchronized with the APP display?
   • Please confirm that the center pieces on each side of the cube are correct
   • Please reset the cube state through the reset function of the app (reset to the original state/reset to color).
   • When the cube’s battery is low, it will automatically go into hibernation, causing the cube’s status to be unable to sync. Please replace the battery as soon as possible.
3. For more questions, please visit one-think.com for technical support or contact us at service@one-think.com.

BATTERY PRECAUTIONS

1. The product uses two 3V CR1632 non-rechargeable coin batteries;
2. The battery should be removed and installed correctly according to the polarity and voltage marks on the toy battery compartment, and the battery should not be short-circuited;
3. Non-rechargeable batteries cannot be charged;
4. Different types of batteries or old and new batteries cannot be mixed;
5. Only batteries that are the same or equivalent to the recommended battery can be used;
6. The exhausted battery should be removed from the toy.
   • If it is not used for a long time, please remove the battery from the device;
7.  The power terminal shall not be short-circuited;
8. It cannot be connected to more than the recommended number of power supplies.

FCC

ID: 2BK6JQY-31002

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Documents / Resources

QYTOYS QYSC-S QY Smart Cube [pdf] Instruction Manual QYSC-S, QYSC-S QY Smart Cube, QY Smart Cube, Smart Cube, Cube

References

• User Manual