QLIGHT P340 Multipurpose High Bay Motion Sensor
Application
Automatically ON/OFF function:
Daylight threshold is on 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/200Lux；
Standby period is 0s; Light on when detect movement and off after people leave at night. Applications: Corridor, Staircase.
- With sufficient daylight, even when motion detected, light remains OFF.
- With insufficient daylight, when motion detected, light ON.
- After the last detection and the present hold time elapsed, light OFF.
No daylight function
Daylight threshold is on “Disable”; Standby period is on 0s/10s/30s/1min/5min/10min/30min/60min.
Light on when detect movement, After people leave, Light off after stand-by period.
Stand-by period is set to +∞，The light will always remain ON.
- When motion is detected, the sensor will switch on the light to 100% brighteness.
- After people leave the detection area, light remains 100% brightness within hold time.
- After the last detection and the present hold time elapsed, light OFF.
Function Demo – Dimmable control/Corridor function
Daylight threshold is on 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/200Lux;
Standby period is on 0s/10s/30s/1min/5min/10min/30min/60min.
Light on when detect movement and off after people leave at night. Applications: Corridor, Staircase.
- With sufficient daylight, even when motion detected, light remains OFF.
- With insufficient daylight, when motion detected, light ON.
- After last detection, the light will be dimmed down to the stand-by dimming level (10%, 20%,30% or 50%) after holdtime.
- After the stand-by period, light OFF.
Daylight Priority
Dusk/Dawn sensor:
Dual-PD technology brings a fully automatic dusk/dawn sensor which can tell the difference between natural light and LED light, to ensure the light will be off when needed.
Precondition of Daylight priority:
- Daylight threshold is on 30Lux/50Lux/80Lux/120Lux;
- Standby period is +∞ ；
- Standby dimming level is on 10%/20%/30%.
Application____Daylight priority
Daylight threshold is on 30Lux/50Lux/80Lux/120Lux;
Standby period is +∞; Standby dimming level is on 10%/20%/30%.
- Light automatically on when ambient brightness is lower
- With insufficient ambient brightness, light dims to 100%
- Light dims to standby level if no motion detected after holdtime.
- Light off when ambient lux level is higher than preset lux amount.
Specification
| Input | Voltage | 10.5-15V DC (Currect Required>30mA) |
| Standby Consumption | <30mA (Power Consumption） | |
| Output | Dim Output | DIM 1-10V |
| Daylight Priority Function | Detection area：120Lux/80Lux/50Lux/30Lux Stand-by period：+∞ Stand-by dimming level：10%/20%/30% | |
|
Sensor Parameters | Detection Area | 25%/50%/75%/100% |
| Holdtime | 5s/30s/1min/3min/5min/10min/20min/30min | |
| Daylight Threshold | 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable | |
| Stand-by Period | 0s/10s/30s/1min/5min/10min/30min/60min+∞ | |
| Stand-by Dimming Level | 10%/20%/30%/50% | |
| Microwave Frequency | 5.8GHz±75MHz | |
| Microwave Power | <0.3mW | |
| Mounting Height | ≤12m/39.36ft (Ceiling Mounted) | |
| Detection Range | Max,ø16m/52.49ft (Ceiling Mounted) | |
| Motion Detection | 0.5~1m/s | |
| Others | Temperature | -20°C~+60°C |
| IP Grade | IP65 | |
| Warranty | 5 Years | |
| Remark | Factory Default Setting: Detection area 100%/ Hold time 5s/ Daylight threshold Disable/ Stand-by period 0s/Stand-by dimming level 10%. | |
Detection coverage
Typical installation height 8-12m.
This figure indicates the maximum distance at the highest mounting height with 100% sensitivity.
Documents / Resources
 | QLIGHT P340 Multipurpose High Bay Motion Sensor [pdf] Instruction Manual P340 Multipurpose High Bay Motion Sensor, P340, Multipurpose High Bay Motion Sensor, High Bay Motion Sensor, Bay Motion Sensor, Motion Sensor, Sensor |
