QiDi PLUS5 3D Printer User Guide

PLUS5
Please read this guide carefully
before using this product
Quick Start Guide

All pictures are for illustrative purposes only, actual product may vary due to product optimization.

Printer Introduction

Print Head Introduction

How to Remove the Print Head Front Cover

The print head front cover features a buckle structure on the top. Do not remove it directly. First, unlock it by lifting it upward, then remove the print head front cover outward and laterally.

QIDI Studio

There is QIDI Studio slicing software in the USB flash drive. After installing and operating it, you can learn how to use the software in the User Manual.

Starting Up

1. Open the packaging box. Remove the top foam and the glass cover box,
2. Take out the printer.
3. Take out the accessory box.
   If you have purchased the “Plus5 Combo”, please remove the accessory box according to the instructions on the attached card.
4. Take out the power cord from the accessory box and plug it into the printer.
5. Turn on the printer.
6. Follow the on-screen instructions to complete the startup setup.

First Printing

Click the button to start printing.
*Pre-saved models files use PLA Rapido filament by default.

Tips

1. Some other brands of ABS filaments are less heat resistant and it is recommended to set the chamber temperature no more than 55 degrees Celsius. Otherwise the filaments may be softened in advance and cause clogging.
2. If the filaments do not stick to the print platform:
   1) Please check if the nozzle is far away from the print plate, you can adjust the platform upward by Z-offset adjusting function.
   2) Because of the different ambient temperatures in different regions, the temperature of the heat bed can be increased appropriately to increase the adhesion of the filaments.
   3) If above all can not work, please contact the after-sales service for assistance.

Usage Notice

• Do not place the machine near flammable or explosive materials or high-temperature sources. Please place the machine in a ventilated, cool, and low-dust environment.
• Ensure the machine is powered off (unplug power cord) before performing maintenance or modifications.
• Before applying power to the machine, check that the voltage is correct.
• Never reach inside QIDI printers while they are in operation.
• Children should be under constant supervision when using QIDI products.
• The printer contains high-speed moving parts, so be careful of hands pinching.
• There is a potential risk of burns: the print head of the QIDI printers can reach temperatures above 300 °C, while the hot bed can reach temperatures above 100 °C. Do not touch either of these parts with your bare hands.
• Do not place the printer in a vibrating or other unstable environment. Otherwise the shaking of the machine will affect the printing quality.
• After printing, use the residual temperature of the print head to clean the filament around the nozzle with the dedicated tools in time. Do not touch either of these parts with your bare hands.
• Regular maintenance of the printer is essential. When the printer is powered off, use a dry cloth to clean the printer body, removing dust, residual filaments, and foreign objects from the optical axes.
• The linear guides and Z-axis lead screws require periodic cleaning and lubrication.
• If the machine is in standby mode for a long time, please unplug the power of it.
• If the machine is not used for a long time, please pay attention to protect the printer from dust and damp.
• Modifying system files or installing non-official plugins constitutes a voluntary waiver of official technical support. Users assume all risks associated with such actions, including firmware malfunctions, system failures, or other issues, which are explicitly excluded from warranty coverage. To restore the original system state, perform a “Factory Reset” via the settings interface.

Contact Information

There are manuals, slicer software and other related informations in the USB flash drive. For more detailed instructions and precautions, please refer to the electronic version of the manual in the U disk or obtain the latest information according to the contact information below.
If you need support, please feel free to contact us :
After-sales Service E-mail address: Plus5support@qidi3d.com/Plus5support02@qidi3d.com
Official website: www.qidi3d.com
You can check the official Wiki of QIDI Tech for more tutorials on machine usage and maintenance: https://wiki.qidi3d.com/en/home
TEL: 0086-577-66881077
If you have any suggestions or complaints, please contact with this E-mail address: Karl@qd3dprinter.com

https://wiki.qidi3d.com/en/home

https://www.facebook.com/QIDI3D	https://www.reddit.com/r/QidiTech3D/
https://www.youtube.com/@QIDITech	https://twitter.com/QIDI_3dprinter