QCY TWS Bluetooth Earbuds QCY-T6
QCY TWS Bluetooth Earbuds QCY-T6

QR Code
For better using experience, please scan to download QCY app before start-up.

Overview

Choose Your Eartips
Please try medium eartips first as they fit most people.

Eartips

Earbud

Earbuds Overview

Charging case

Charging case Overview

How to Pair

First Time Pairing:

  1. Pick up both earbuds, pop both earbuds into the case to activate them.
  2. On cellphone, search forQCY-T6 and tap to connect.

* Once paired earbuds will auto power on upon picking up from the case. If earbuds fail to auto power on, please charge them and try again.

Switch Paired Device:

  1. Turn off phoneA’s Bluetooth faculty and earbuds will auto disconnect and enter into pairing mode.
  2. On phoneB, search for QCY-T6 and tap to connect.

* Multi-point connection is not available. Earbuds will auto reconnect to phoneB upon powering up again.

Pairing Inductions

Factory Setting

Try the following steps to fix connectivity issue)
Set to factory:

  1. On cellphone, search for QCY-T6, tap and choose ignore or cancel pairing.
  2. Pick up two earbuds, keep touching both bars for 8s or until LEDs glow red for ls to power off.
  3. Keep touching both bars for lOs or until LEDs blink red and green 3 times then blink red to set earbuds to factory.

* Please refer “First Time Pairing” to connect after factory setting.
Manual Pairing (please refer the following steps in case two earbuds lose connection)
Power off earbuds then keep touching panels for Ss or until LEDs blink red and green. After then, double touch panels and LEDs will blink red and green. Two earbuds will then auto pair with each other when LED on master earbud blinks red and green and the other one turns off.

Factory Setting

How to Wear

Wearing Induction

  1. Rotate earbud and pop it into your ear then shake head to check wearing stability.
  2. Please adjust mic towards your mouth to gain better calling experience.

Three-way Calling & Switch
Double touch the bar to answer incoming call. If another call is coming in sync, double touch again to put the first call on hold while activating the second one or keep touching the bar for 2s to ignore the second call. Keep touching the bar for 2s to switch between active call and held call.

Mono Mode

  1. Power off earbuds, hold Touch Panel on either earbud for 5s to enter pairing mode(LED blinks red and green)
  2. On cellphone, search for QCT-T6 and tap to connect
  3. Connected
Charging Earbud

Push earbud into the case to charge. LED will glow solid red when charging and turn to green for l minute once top up.

Charging the Case

LED on the case will glow solid red when battery level is under 60%; LED will turn green when battery level is between 60% and 95 and become solid blue when the battery level is over95%.

Product Parameters

Model: lnl947
Pairing name: QCY-T6
Bluetooth version: V5.0 Stand time: approx. l00hr
Charging time: approx. 2hr Music time: approx. 6 hr
Talking time: approx. 5.5hr
Operation range: l0m(with no obstacle)
Battery type: Ii-ion
Battery capacity(earbud): 3.7V 60mAh
Battery capacity(charging case): 3.7V 600mAh
Input parameter(charging case): SV = 600mA
Bluetooth profiles: HSP/HFP/A2DP/AVRCP

Warranty Card

Warranty Card
Warranty Period

12 months after you purchase this item.(or you may inquire your local shopper for more details.)
Free Service:
Supposing any defects caused by quality issues occur within the warranty period, please take this warranty card and purchase receipts to your distributor for free exchange service.

Free exchange service will not be accessed under following circumstances:

  1. Damages caused unauthorized disassembly.
  2. Defects or physical damages caused by leaking or dropping off.
  3. Damages by act of God.Supposing your item is within any damages or defects except the above circumstances, please return to us or your distributor for free repairing.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the fol lowing two conditions: (1) This device may not cause harmfu l interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Icons

Hazardous substances and their contents in the item

Hazardous
This form is made by SJ/T 11364 regulation.
O: means that hazardous substance content in the homogeneous materials of this part is within the limits of (EU) 2015/863 regulation.
X: means that hazardous substance content in ,at least, one certain homogeneous material of this part is beyond the limits of (EU) 2015/863 regulation, but there is no mature alternative in the industry at present, it still conforms to the EU ROHS Directive in the scope of exemption.

 

Notes: Please arrange using time properly as your hearing may be damaged by using the device for a long time.
Manufacturer: Dongguan Hele Electronics Co., Ltd.
Address: Daojiao Town, Dongguan City, Guangdong, China

Tips

  1. Before using the headset, please read the manual carefully and keep it for future references.
  2. The headset need to be fully charged prior to first-time use.
  3. If the headset is left unused for over two weeks, please recharge it periodically.
  4. Please use the chargers made by qualified manufacturer.
  5. If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please re-enter the mode; if a procedure error of your phone occurs, reboot it; if a procedure error of the head set occurs, reboot or reset it.

Caveats

  1. Never disassemble or modify your headset for any reasons to avoid any damages and danger.
  2. Do not store the headset in extreme temperatures (under 0°C or over 45°().
  3. Avoid using the indicator close to the eyes of children or animals.
  4. Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electric shock.
  5. Do not use harsh chemicals or strong detergents to clean the headset.
  6. Keep the headset dry.

QCY TWS Bluetooth Earbuds QCY-T6 User Manual – OCR PDF
QCY TWS Bluetooth Earbuds QCY-T6 User Manual – Optimized PDF
QCY TWS Bluetooth Earbuds QCY-T6 User Manual – Original PDF

Join the Conversation

1 Comment

  1. Today I bought wireless in-ear hearing aids and as a beginner I still couldn’t pair the qcy-tws-qcy-t6 headphones. Please email me a simple way to do this. Well thank you.
    Dnes som si kúpil bezdrôtové sluchadla do uší a nakoľko som začiatočník stále sa mi nepodarilo spárovať slúchadla qcy-tws-qcy-t6. Prosím Vás napíšte mi jednoduchým spôsobom ako to mám urobiť. Ďakujem.

Leave a comment

Your email address will not be published.