Wall Plate Manuals & User Guides

ELEGRP PA-APTR-LB Three Single Pole Switch With Wall Plate User Guide

August 19, 2026

ELEGRP PA-APTR-LB Three Single Pole Switch With Wall Plate About this item 【Rational Design】 Three decorator style light switch features two smooth ON and OFF paddles with very good tactical feedback that prevent accidental flips of the switch. 【High Quality】…

Brand: ELEGRP

BESTTEN PA-APCO-L2A Combination Two Single Pole Switch And Receptacle With Wall Plate User Guide

August 19, 2026

BESTTEN PA-APCO-L2A Combination Two Single Pole Switch And Receptacle With Wall Plate SPECIFICATION Features & Specs Operation Mode ON-OFF Current Rating 15 A Operating Voltage 120 volts Contact Type Normally Open Connector Type Clamp Switch Type Rocker Terminal Screw Circuit…

Brand: Bestten

asa ELECTRONIC BTWP2 Bluetooth Wall Plate Instruction Manual

July 6, 2026

asa ELECTRONIC BTWP2 Bluetooth Wall Plate INTRODUCTION Thank you for choosing the BTWP2. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll…

Brand: asa ELECTRONIC

altronics DIT2 Mic/Line Input Dante Wall Plate Owner’s Manual

March 11, 2026

DIT2 Mic/Line Input Dante Wall Plate Introduction DIT2 is designed to accept Mic input and RCA Line level input with the Dante interface. Equipped with high performance of microphone pre-amplifier circuit and phantom power, DIT2 supports condenser or dynamic microphone…

Brand: ALTRONICS

Milestone MP-WP-DAN Dante Wall Plate User Manual

March 4, 2026

Milestone MP-WP-DAN Dante Wall Plate Product Introduction Thank you for choosing the MP-WP-DAN audio wall plate. It receives signals from Bluetooth and converts them into Dante network data for output. One-touch pairing simplifies connectiom The device is powered via POE…

Brand: Milestone

asa ELECTRONICS BTWP2F Filter Bluetooth Wall Plate Installation Guide

December 2, 2025

asa ELECTRONICS BTWP2F Filter Bluetooth Wall Plate Product Information Specifications Date Released: 10/29/25 Document Revision: A Model/Part No.: BTWP2F, BTWP2 Tracking Number: TB10104 Written By: D. Robinson Product Usage Instructions Disconnect the speaker harness from the back of the BTWP2.…

Brand: asa ELECTRONICS

MuxLab SE-001022-A Dante 2-Channel XLR Wall-Plate User Manual

November 25, 2025

MuxLab SE-001022-A Dante 2-Channel XLR Wall-Plate Product Information Specifications XLR Impedance Input: Balanced 20k Ohm XLR Impedance Output: Balanced 100 Ohm Dante Interface: RJ45 interface with PoE Frequency Response: 20Hz-20kHz Sampling Rate: 48kHz Floor Noise: -90dB Channel Isolation: 100dB @…

Brand: MuxLab

peerless-AV WSP756 Metal Stud Wall Plate Instruction Manual

October 1, 2025

peerless-AV WSP756 Metal Stud Wall Plate WARNING This product is designed to be installed on metal stud walls. Hardware is included for metal stud installation. Before installing make sure the supporting surface will support the combined load of the equipment…

Brand: Peerless-AV

CaseBot 2022 Wall Plate User Manual

September 20, 2025

CaseBot 2022 Wall Plate CaseBot Wall Plate Compatible With Installation Instructions Dimensions

Brand: CaseBot

BLUSTREAM DA11ABL Bluetooth and Analog Audio Dante Wall Plate User Guide

September 11, 2025

DA11ABL-WP-US-V2 Quick Reference Guide Introduction The DA11ABL-WP-US-V2 is a multi-input / output wall plate to convert Bluetooth and analog audio within a digital Dante® networked audio system. The DA11ABL-WP-US-V2 converts 2 input channels of Bluetooth or unbalanced audio to Dante®…

Brand: BLUSTREAM