Q-TRAN FL3SC Linear Fixtures Surface

Introduction

• Encapsulated with polyurethane for indoor and outdoor locations (IK10)
• Perfect for recess mounted installations
• Features high quality LED strips encapsulated in a rigid extrusion providing a robust fixture for various environments
• Delivers superior uniform light output and luminosity
• Q-Tran Red & Amber LED products are Florida Fish and Wildlife Conservation Commission certified, making them safe for turtles and other wildlife
  

1 PRODUCT

2 WATTS/ FT

3 CCT

4 RATED

5 EFFICIENCY

6 LENS

7 WIRE INPUT/ OUTPUT

8 CONNECTOR/ WIRE IN

9 CONNECTOR/ WIRE OUT

10 INPUT END CAP

11 OUTPUT END CAP

12 WIRE COLOR

13 WIRE TYPE

14 MOUNTING

15 FINISH

16 LENGTH (IN)

17 EXACT/OPTIMAL

FL3SC

5.0

ENC

STD

STD

SST

1. PRODUCT FL3SC
   See last page for compatible power supplies
2. WATTS/FT
   5.0 5.0W/ft
3. CCT
   
   • A Amber
     
   • B Blue
     
   • G Green
     
   • R Red
4. RATED
   ENC IP67
5. EFFICIENCY
   STD Standard
   WO White Optics
   White Optics – Internal coating, greater lumen output
6. LENS
   • CL Clear
   • TL Translucent
     For representation of LED visibility, see Diode Visibility section on following pages.
     For beam angles, see Photometric Performance section on following pages
7. WIRE INPUT/OUTPUT
   • S1 Single 1 (Input only) – End Feed
     S2 Single 2 (Input only) – Bottom Feed
     For continuous mounting, consider bottom feed
   • P1 Pass Through 1 (Input/output) – End Feed
     P2 Pass Through 2 (Input/output) – Bottom Feed
     For continuous mounting, consider bottom feed
8. CONNECTOR/WIRE IN
   • BW: Bare Wire (Standard 24″)
     BRL: Barrel
     CON6: Connector 6″
     CON24: Connector 24″
     Connector/Wire In not needed to specify product. Typical selection is BW.
     BW: Standard length is 24″, Max length is 120″. Request custom length by writing in part number next to BW (example: BW48)
   • BW: Bare Wire (Standard 24″)
     BRL: Barrel
     CON6: Connector 6″
     CON24: Connector 24″
   • Connector/Wire In not needed to specify product. Typical selection is BW.
     BW: Standard length is 24″, Max length is 120″. Request custom length by writing in part number next to BW (example: BW48)
9. CONNECTOR/WIRE OUT
   • CLS Closed End (No feed)
   • BW: Bare Wire (Standard 24″)
   • BRL: Barrel
   • CON6: Connector 6″
   • CON24: Connector 24″
     Connector/Wire Out not needed to specify product. Typical selection is CLS or BW.
   • BW: Standard length is 24″, Max length is 120″. Request custom length by writing in part number next to BW (example: BW48)
10. INPUT END CAP
    
    • STD: Standard
      STD – End cap matches fixture finish chosen
11. OUTPUT END CAP
    
    • STD: Standard
      STD – End cap matches fixture finish chosen
12. WIRE COLOR
    • WH White
    • BK Black
    • N/A For Barrel
13. WIRE TYPE
    
    • CL2 Class 2
      
    • CL2P Plenum Rated
      
    • N/A For Barrel
      CL2P only available with bare wire leads (BW)
14. MOUNTING
    
    • SST: Stainless Steel
15. FINISH
    
    • ST Satin
    • BK Black
16. LENGTH (IN)
    Fixture length min 12”, max 98.43” not including end caps.
    Tolerance +0 – 1/8”. Consult factory for lengths under 12″

PRODUCT – DIMENSIONS

DELIVERED LUMENS

• [Calculated L70 = 40000 hrs]
• Tested with FL3SC-5.0-**-ENC-STD

	Red	Green	Blue	Amber
	LM/FT	LM/F1	LM/FT	LM/FT
CL	56	304	79	51
TL	35	191	50	32

DIODE VISIBILITY

	ENC/CL – Clear encapsulation
	ENC/TL – Translucent encapsulation

WIRE INPUT/OUTPUT

SINGLE (Input only)

PASS THROUGH (Input/Output)

CONFIGURATION OPTIONS

CONNECTOR/WIRE – IN/OUT

Connector/Wire In or Out not needed to specify product. Standard configuration is BW for Wire In and CLS for Wire out

WIRE COLOR

MOUNTING

• 2 clips provided for 4′ or less; 4 clips provided for greater than 4′
• To order separately use SST-01
• Each clip comes with a #4 x 5/8″ Flat Head screw
  

FINISH

EXACT/OPTIMAL FIXTURE LENGTH

EXAMPLES OF 12 OPTIMISE STATIC WHITE FIXTURES WITH DIFFUSED LENS

SC ENC LENGTHS BY INCH

Exact fixtures are the length specified. Optimal fixtures’ length is rounded down with illumination end to end. All fixtures’ tolerance is +0 – 1/8”. Consult factory for lengths under 12″.

EXACT LENGTH

Requested Length	Potential dim spot on either end of fixture
12″	1″
13″	o.5″
14″	1″
15″	0.5″
16″	1″
17″	0.5″
18″	1″
19″	o.5″
20″	1″
21″	o.5″
22″	1″
23″	o.5″
24″	1″
36″	1″
4811	1″
60″	1″
72″	1·
84″	1·
96″	1·

OPTIMAL LENGTH: highlighted rows are closest to requested nominal length

Requested Nominal Length	S1 & S2		P1  & P2
12·	10.5′		10.75 “
13″	12.5 “		12.75″
14“	12.5″		12.75″
15•	14. 5″		14.75″
16″	14.5″		14.75 “
17″	16. 5″		16.75″
18″	16. 5″		16.75″
19″	18. 5″		18.75″
20·	18. 5″		18.75 “
21″	20. 5″		20.75″
22·	20.5″		20.75″
23″	22.5″		22.75″
24“	22.5″		22.75″
36″	34. 5″		34.75″
48″	46.5″		46.75″
60″	58.5″		58.75″
72″	70.5′		70.75″
84″	82.5″		82.75″
96″	94.5′		94.75″

COMPATIBLE POWER SUPPLIES

See power supplies cut sheets for more information. Data subject to change, all data has +/- 5% tolerance.

DIM TO LEVEL	INDOOR	OUTDOOR
	SC	SC
Dim to Black	06 M-DC+CAP QTM-DC+CAP iO-PH iO-PH+OD1	OOM-DC+CAP QOM-PHIO-PH
0.1%	OTM-eLED+0-10V QTM-eLED+AN QZ-DMX OZ-PH/0-10V QZ-STICK-PH/0-10V OZLP	Q-SET-OZ-DMX O-SET-QZ-PH/0-10V Q-SET eLED+0-10V QOM-eLED+0-10V QZ-DMX QZ-PH/0 -10V
1%	QTM-eLED(E) QTM-eLED(L) OTM -eLED+DALI-DT6 QTM-eLED+DALI -DT6 AN	QOM-eLED+DALI-DT6
10″/4	Non-Dim Power Supply with SW App Dongle

DIMMING PROTOCOL	IOIOOOR	OUTDOOR
	SC	SC
Non-Olm	OTM-eLE.0-.ND QZ-NO	Q-SET-QZ-ND Q-SET-eLED-ND QOM-eLED-ND QZ-ND iQ-ND-50-65
Pha-se	Q6M-DC+CAP QTM-DC+CAP QTM-eLED(E) QTM-eLED(L) QZ-PH/0-10V QZ-STICK-PH/0-10V QZLP iQ-PH iQ-PH+QD1	Q-SET-QZ-PH/0-10V QOM-DC+CAP QOM-PH QZ-PH/0-10V iQ-PH
0-IOV	QTM-eLED+0-10V QTM-eLED+AN QZ-PH/0-10V QZ-STICK-PH/0-10V QZLP	Q-SET-QZ-PH/0-10V Q-SET-eLED+0-10V QOM-eLED+0-10V QZ-PH/0-10V
Lutron Athena	QTM-eLED+AN QTM-eLED+DALI-DT6-AN
ECO System	QTM-eLED(E)
DMX	QZ-DMX	Q-SET-QZ-DMX QZ-DMX
DALI-2: DT6	QTM-eLED+DALI-DT6 QTM-eLED+DALI-DT6-AN	QOM-eLED+DALI-DT6
SCENE App Dimmed	Non-Dim Power Supply with SW App Dongle

COMPATIBLE MOUNTING ACCESSORIES

HINGE – HMB-M	HINGE – HMB-L	HINGE – HMB-XL	a-PIVOT	a-ANGLE
Adjustable mounting bracket – Medium	Adjustable mounting bracket – Large	Adjustable mounting bracket – Xlarge	Small mounting accessory	Adjustable mounting accessory

COMPATIBLE WIRING ACCESSORIES

Q-mlnl-J	BARREL-EXT	BARREL FOUR-FER	CON-EXT	CON FOUR-FER
UL Listed, miniature Junction box	8ft barrel cable bracket extender	Splits lead from one to four LED Barrel connector fixtures	1Oft Con cable extender	Splits lead from one to four LED Con  connectors

5 year warranty

• Field modifications void warranty
• Data subject to change, all data has +/- 5% tolerance
• Compatible for use with Q-Tran power supplies
• Florida Fish and Wildlife
• Conservation Commission (FWC) rated Strips: Red and Amber
• IK10 rated
• Patent # D798,471 S

Customer Support

© 2023 Q-Tran Inc. All rights reserved
155 Hill St. Milford, CT 06460
203-367-8777
sales@q-tran.com
www.q-tran.com

Documents / Resources

Q-TRAN FL3SC Linear Fixtures Surface [pdf] Owner's Manual FL3SC Linear Fixtures Surface, FL3SC, Linear Fixtures Surface, Fixtures Surface, Surface

References

• User Manual