GZYF LIRU MLS062 Universal Motorcycle LCD LED Digital Odometer Speedometer Gauge Instruction Manual

1. پیژندنه

This manual provides detailed instructions for the installation, operation, and maintenance of your GZYF LIRU MLS062 Universal Motorcycle LCD LED Digital Odometer Speedometer Gauge. Please read this manual thoroughly before installation and use to ensure proper function and safety.

1.1 د خوندیتوب معلومات

• Always disconnect the motorcycle's battery before performing any electrical work.
• ډاډ ترلاسه کړئ چې د تارونو ټولې اړیکې خوندي او په سمه توګه موصل شوي دي ترڅو د لنډ سرکټ مخه ونیول شي.
• Mount the speedometer securely to avoid vibration damage or detachment during operation.
• که تاسو د نصبولو د کومو ګامونو په اړه ډاډه نه یاست، نو د وړ تخنیکین سره مشوره وکړئ.

2. د بسته محتويات

ډاډ ترلاسه کړئ چې ټول توکي په کڅوړه کې شتون لري:

• 1 x GZYF LIRU MLS062 Digital Odometer Speedometer Gauge
• 1 x Speed Sensor
• Mounting Hardware (as pictured)

Image 2.1: The GZYF LIRU MLS062 Digital Odometer Speedometer Gauge, including the speed sensor and small mounting components.

3. محصول ختم شوview

The MLS062 is a universal digital gauge designed for motorcycles, providing essential riding information on a clear LCD LED display.

انځور 3.1: مخکی view of the speedometer unit, showing the display area and control buttons.

انځور ۵.۱: اړخ view of the speedometer unit, highlighting its compact design.

3.1 کلیدي ځانګړتیاوې

• LCD LED Digital Display
• Speedometer (Max 199 units)
• Odometer (Max 99999.9)
• Trip Meter (Max 999.9, resettable)
• RPM Gauge (Max 14000r/min)
• Gear Indicator (N, 1-6)
• 24-ساعت ساعت
• Turn Signal, High Beam, and Neutral Indicators

4. مشخصات

Image 4.1: Dimensional diagram of the speedometer unit, showing measurements in millimeters.

5. ترتیب او نصب کول

The MLS062 speedometer is designed for universal fitment on 12V motorcycles. Professional installation is recommended.

5.1 Mounting the Speedometer

1. Choose a suitable location on your motorcycle's dashboard or handlebar area for optimal visibility.
2. Use the provided mounting hardware to securely attach the speedometer unit. Ensure it is stable and does not obstruct your view یا کنټرولونه.

5.2 د تارونو نښلول

Refer to the wiring diagram (if provided with your unit) and the image below for typical connections. The speedometer uses standard multi-pin connectors.

Image 5.1: Close-up of the wiring harness connectors, showing multiple pins for various functions.

• Power (12V): Connect the positive wire to a switched 12V power source (e.g., ignition). Connect the negative/ground wire to the motorcycle chassis.
• د سرعت سینسر: Connect the speed sensor wires to the corresponding input on the speedometer harness.
• د RPM سیګنال: Connect the RPM signal wire to the motorcycle's ignition coil or ECU RPM output.
• د ګیر موقعیت: Connect the gear position wires (N, 1-6) to the motorcycle's gear sensor outputs.
• شاخصونه: Connect wires for turn signals (left/right), high beam, and neutral light to their respective motorcycle circuits.

5.3 د سرعت سینسر نصب کول

1. Mount the speed sensor near a rotating part of the wheel (e.g., brake disc bolts, wheel spokes) that can trigger the sensor.
2. Ensure the sensor is positioned correctly to detect rotations consistently. Adjust the gap between the sensor and the trigger point as needed.

6. عملیاتي لارښوونې

Once installed and powered on, the speedometer will display various information. The unit typically features two buttons for control, often labeled 'SEL' (Select) and 'ADJ' (Adjust).

Image 6.1: The MLS062 speedometer display shown in an operational state on a motorcycle dashboard, indicating speed, RPM, and gear.

6.1 ښودل حالتونه

• Press the 'SEL' button briefly to cycle through different display modes: Odometer (ODO), Trip Meter (TRIP), and Clock.
• The main display will always show current speed and RPM.

6.2 Resetting Trip Meter

• While in TRIP mode, press and hold the 'ADJ' button for a few seconds to reset the trip meter to zero.

6.3 د ساعت تنظیم کول

1. Navigate to the Clock display mode using the 'SEL' button.
2. Press and hold the 'SEL' button until the hour digits begin to flash.
3. Use the 'ADJ' button to adjust the hour.
4. Press 'SEL' again to move to the minute digits, then use 'ADJ' to adjust minutes.
5. Press 'SEL' one more time to save the settings and exit clock adjustment mode.

6.4 Unit Switching (MPH/KMH)

The method for switching between Miles Per Hour (MPH) and Kilometers Per Hour (KMH) may vary. Typically, this is done by:

• Turning off the ignition.
• Pressing and holding the 'SEL' button while turning the ignition back on.
• Release the button once the unit changes.

Note: Refer to specific instructions provided with your unit if this method does not work.

7. ساتنه

The GZYF LIRU MLS062 speedometer requires minimal maintenance.

• پاکول: یو نرم استعمال کړئ، دamp د نندارې د پاکولو لپاره ټوکر او جasing. Avoid abrasive cleaners or solvents that could damage the plastic.
• اړیکې: Periodically check all wiring connections for tightness and corrosion. Ensure the speed sensor is clean and free from debris.
• د چاپیریال ساتنه: While designed for motorcycle use, prolonged exposure to extreme weather conditions (heavy rain, direct sunlight) may affect longevity. Consider a protective cover when parking for extended periods.

8. ستونزه حل کول

9. تضمین او ملاتړ

For warranty information or technical support, please refer to the seller or manufacturer's contact details provided at the point of purchase. Keep your purchase receipt as proof of purchase.