EasyMote Universal Big Button TV Remote

2.1 کلیدي ځانګړتیاوې

• Dual Device Control: Controls both your TV and Cable Box (IR) with a single remote.
• ساده ډیزاین: Features 6 large, bright, backlit buttons for basic TV control.
• Clear Text: Buttons have clear and big text for easy visibility, even in low light conditions.
• د لاس پټه: Includes a strong, comfortable wrist strap to prevent misplacement.
• Universal Library: Equipped with a 'Quick Search' function to scan for TV codes quickly.
• د زده کړې حالت: Allows programming of each button to a custom command from your original TV or Cable Box remote.

2.2 اجزا

• EasyMote DT-R08W Remote Control
• Wrist Strap (pre-attached)
• د لارښود لارښود (دا سند)

Note: 2 AA batteries are required and not included.

2.3 محصول Views

مخکی view of the EasyMote remote, showing the large, green backlit buttons and attached wrist strap.

ګڼ views of the EasyMote remote, illustrating its ergonomic design and battery compartment on the back.

Close-up of a hand holding the EasyMote, highlighting the bright, green backlit buttons for enhanced visibility.

3.1 د بیټرۍ نصب کول

1. Locate the battery compartment on the back of the EasyMote remote.
2. د خلاصولو لپاره د بیټرۍ پوښ ښکته خوا ته وغورځوئ.
3. ۳ AA بیټرۍ دننه کړئ، د سم قطبیت (+ او -) ډاډ ترلاسه کړئ لکه څنګه چې د خونې دننه ښودل شوي.
4. د بیټرۍ پوښ بیرته ځای پر ځای کړئ تر هغه چې په خوندي توګه کلیک وکړئ.

3.2 Programming the EasyMote

The EasyMote can be programmed using two methods: Quick Search (Auto-Scan) or Learning Mode (from your original remote).

Method 1: Quick Search (Auto-Scan)

This method allows the EasyMote to automatically scan for compatible TV codes.

1. Ensure your TV is turned ON.
2. On the EasyMote, press and hold the خاموش او CH+ buttons simultaneously for approximately 5 seconds until the red indicator light stays on. This indicates programming mode.
3. While in programming mode, repeatedly press the CH- button. The remote will cycle through pre-programmed codes. Observe your TV screen.
4. When your TV changes channels, immediately press the خاموش button on the EasyMote to lock in the code. The red indicator light will turn off.
5. Test all buttons (ON/OFF, VOL+, VOL-, CH+, CH-, MUTE) to verify full functionality. If some buttons do not work, repeat the process as the remote may have found a partial match.

Method 2: Learning Mode (from Original Remote)

This method is ideal for programming specific functions from your existing TV or Cable Box remote, especially for cable box channel control.

1. Place the EasyMote and your original remote control on a flat surface, pointing their IR emitters directly at each other, about 2 inches apart.
2. On the EasyMote, press and hold the خاموش او VOL+ buttons simultaneously for approximately 5 seconds until the red indicator light stays on. This indicates learning mode.
3. Press the button on the EasyMote that you wish to program (e.g., ON/OFF). The red indicator light will start blinking slowly.
4. On your original remote, press and hold the corresponding button (e.g., ON/OFF). The EasyMote's red indicator light will blink rapidly, then stay solid, indicating successful learning.
5. Repeat steps 3 and 4 for all other buttons you wish to program (VOL+, VOL-, CH+, CH-, MUTE).
6. Once all desired buttons are programmed, press and hold the خاموش او VOL- buttons simultaneously on the EasyMote until the red indicator light turns off. This saves the learned commands and exits learning mode.
7. Test all programmed buttons to ensure they function correctly.