Leviton 15 Amp 125 Volt Industrial Grade Straight Blade Grounding Connector (Model 1547)

محصول پای ته ورسیدview

د لیویټون ۳۰ Amp, 125 Volt, Straight Blade, Industrial Grade, Dustguard, Grounding Connector, Model 1547, is engineered for demanding environments. Its rugged construction resists impact, sunlight, chemicals, and rough use. Key features include solid one-piece contacts for superior conductivity and an ergonomic, fluted-body design with a radial gripping edge for easy handling. The unique cord clamp accommodates a wide range of cord sizes, ensuring a secure grip without damaging the cord. This connector is designed to meet IP44 splash-proof and dust-tight standards. The Santoprene Husk material provides resistance to oil, acids, alkalis, and many industrial solvents, and is developed to withstand dusty and dirty environments, cracking, fading, and temperature extremes.

Image: Leviton 1547 Industrial Grade Straight Blade Grounding Connector, Yellow.

د خوندیتوب مهم معلومات

خبرداری: د بریښنا شاک یا اور خطر. This product must be installed and used in accordance with national and local electrical codes. If you are unsure about any part of these instructions, consult a qualified electrician. Always disconnect power at the circuit breaker or fuse box before installing or servicing this product. Do not use this product if it appears damaged. This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning).

• Always ensure power is OFF before installation or maintenance.
• د ټاکل شوي بریښنایی درجې څخه ډیر مه کوئ (15) Amp، ۲۵۰ ولټه).
• ډاډ ترلاسه کړئ چې د ځمکې سره سمې اړیکې جوړې شوې دي.
• له ماشومانو لرې وساتئ.
• Do not immerse in water. This product is splash-proof, not waterproof.

د نصبولو لارښوونې

Follow these steps for proper wiring and assembly of the connector:

1. کیبل چمتو کړئ: Strip the outer jacket of your electrical cable to the appropriate length, typically 1 to 1.5 inches, exposing the insulated conductors (hot, neutral, ground). Strip approximately 1/2 inch of insulation from each conductor.
2. نښلونکی جلا کړئ: Unscrew the housing of the Leviton 1547 connector to separate the body from the wiring module.
3. کیبل داخل کړئ: Thread the prepared cable through the cord clamp and into the connector body.
4. د تار نښلول: Connect the insulated conductors to the corresponding terminals on the wiring module.
   • شنه یا بربنډ مسو تار: Connect to the grounding screw (green).
   • White Wire (Neutral): Connect to the silver screw.
   • Black Wire (Hot): Connect to the brass screw.
   Ensure all wire strands are securely under the screw heads and tightened firmly. Double-check that no stray wire strands are touching other terminals.
5. Secure Cord Clamp: تار کلک کړئ clamp screws to secure the cable, ensuring a firm grip without overtightening, which could damage the cord. The cord clamp prevents strain on the wire connections.
6. Reassemble Connector: Carefully align the wiring module with the connector body and screw the housing back together until it is tight. Ensure no wires are pinched during reassembly and that the connector is fully sealed.

عملیات

Once properly installed and assembled, the Leviton 1547 connector functions as a standard electrical plug. Insert the connector into a compatible 125 Volt, 15 Amp, straight blade receptacle (NEMA 5-15R) to establish an electrical connection. Ensure the connection is firm and secure. To disconnect, grasp the connector body and pull it straight out from the receptacle; do not pull by the cord.

ساتنه

To ensure continued safe and reliable operation of your Leviton 1547 connector, perform the following maintenance:

• منظم معاینه: Periodically inspect the connector for any signs of wear, damage, cracks, discoloration, or exposed wiring. Check the cord clamp د ټینګښت لپاره.
• پاکول: The Dustguard design helps protect internal components from dust and moisture. Clean the exterior of the connector with a dry, soft cloth. Do not use harsh chemicals, solvents, or abrasive cleaners, as these can damage the Santoprene Husk material.
• د چاپیریال ساتنه: While designed for industrial use and resistance to various elements, avoid prolonged exposure to extreme conditions beyond its specifications.
• بدلول: If the connector shows any signs of significant damage, such as deep cracks in the housing, bent or corroded blades, or if the cord clamp is no longer securing the cable, replace the connector immediately. Do not attempt to repair damaged electrical components.

د ستونزو حل کول

If you encounter issues with your Leviton 1547 connector, refer to the following table for common problems and solutions:

تخنیکي مشخصات

تضمین او ملاتړ

This Leviton product is backed by a د 10 کال محدود تضمین. This warranty covers defects in materials and workmanship under normal use. For specific details regarding warranty coverage, limitations, and how to make a claim, please refer to the official Leviton webد لیویټون پیرودونکي خدماتو سایټ یا مستقیم اړیکه ونیسئ.

For technical assistance, product inquiries, or support, please visit the official Leviton webسایټ (www.leviton.com) or contact their customer support department. Contact information, including phone numbers and email addresses, can typically be found in the 'Support' or 'Contact Us' section of their webسایټ