ProtoArc HubMouse User Manual

ProtoArc HubMouse User Manual

www.protoarc.com

US
support@protoarc.com
(+1) 866-287-6188
Mon-Sun: 9AM – 1PM; 2PM – 6PM PT (Eastern Time)
*Closed during Holidays

UK
support-uk@protoarc.com

Product Function

A Left Button
B Right Button
C Scroll Wheel
D DPI Switch Button
E Micro USB Charging Port
F Bluetooth Indicator Light 2
G Bluetooth Indicator Light 1
H USB Indicator Light
I Mode Switch Button
J Power Switch
K USB Receiver
L Low Battery Indicator Light /Charging Indicator Light

Introduction to HUB capabilities

The HUB comes with a 2.4G receiver that is perfectly linked to the mouse

HDMI: Maximum 4K support

USB 3.0: maximum transfer bandwidth up to 5.0 Gbps (500 MB/s)

PD fast charge: the charging power can reach 60W

Support System: Compatible with Mac OS / Windows /Linux/IOS/Android disclaimer

2.4G Connection

Bluetooth Connection

1. Slide the power switch to “ON”.
   
2. Press the mode switch button to switch to BT1 or BT2, the white light flashes slowly.
   Long press the mode switch button for 3-5 seconds until the white light flashes quickly, means that the mouse enters the Bluetooth pairing mode.
   
3. Turn on the Bluetooth settings on your device, search or select “HubMouse” and start Bluetooth pairing until the connection is completed.
   

Mode Switch Method

After completing BT1, BT2 and 2.4G connection, short press the mode switch button on the bottom of the mouse to easily switch between devices.

Short press the mode switch button on the bottom of the mouse.

USB Cable Charging

1. Use the included USB cable to charge the mouse when the battery is low.
   
2. Plug the USB charging cable into the USB port of your computer, the light on the bottom shows red while charging, the charging process is about 4-6 hours (The light flashes red when the battery voltage is 3.7V, at this time the battery needs to be charged, the light turns red while charging and will be off after fully charged).
   

Main Specifications

Engine: Optical
Mouse DPI: 1000/1600/2400 dpi
Mouse Button Life: Over 3 million times click
Capacitance capacity: 300mAh/3.7V
Mouse Size: 109*61*31mm
Mouse Weight: 79g

2.4GHz Transmission Main Specifications:
Transmission Distance: 10 meters
Working Voltage: 3.7V
Working Current: 6.0±0.5mA
Mouse Polling Rate: 250Hz

Bluetooth Transmission Main Specifications:
Transmission Distance: 10 meters
Working Voltage: 3.7V
Working Current: 6.0±0.5mA
Mouse Polling Rate: 125Hz

System Requirement:
Bluetooth Receiving Device, USB port
Windows 8/Windows 10 Version or above
Mac OS × 10.10 Version or above
Android 4.3 Version or above

Package Contents

• 1 × Mouse
• 1 × HUB
• 1 × USB Charging Cable
• 1 × User Manual

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user. is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC ID Warning:
This device complies with Industry Canada licence-ex-empt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.

RF warning statement
The device has been evaluated to meet general ‘RF exposure requirement. The device can be used in portable exposure condition without restriction.