Neuro 200 Advanced Universal Process Indicator
Instruction Manual

This brief manual is primarily meant for quick reference to wiring connections and parameter searching. For more details on operation and application; please log on to www.ppiindia.net

OPERATOR PAGE AND PARAMETERS

Parameters	Settings (Default Value)
Alarm Acknowledge	No Yes (Default : No)
Maximum PV	View Only (Default : NA)
Minimum PV	View Only (Default : NA)
Reset Command	No Yes (Default : No)
Reset Password	0 to 250 (Default : 0)
Alarm-1 Setpoint	Min to max Range specified for the selected Input Type (Default: Min or Max Range)
Alarm-2 Setpoint	Min to max Range specified for the selected Input Type (Default : Min or Max Range)

ALARM PARAMETERS

Parameters	Settings (Default Value)
Alarm-1 Type	None Process Low Process High (Default : None)
Alarm-1 Setpoint	Min to max Range specified for the selected Input Type (Default : Min or Max Range)
Alarm-1 Hysteresis	1 to 999 or 0.1 to 999.9 (Default : 2.0)
Alarm-1 Inhibit	No Yes (Default : Yes)
Alarm-1 Logic	Normal Reverse (Default : Normal)
Alarm Latch	No Yes (Default : No)
Alarm-2 Type	None Process Low Process High (Default : None)
Alarm-2 Setpoint	Min to max Range specified for the selected Input Type (Default : Min or Max Range)
Alarm-2 Hysteresis	1 to 999 or 0.1 to 999.9 (Default : 2.0)
Alarm-2 Inhibit	No Yes (Default : Yes)
Alarm-2 Logic	Normal Reverse (Default : Normal)
Alarm Latch	No Yes (Default : No)

RE TRANSMISSION PARAMETERS

Parameters	Settings (Default Value)
Recorder Output Type	0 to 20mA 4 to 20mA 0 to 5 Volts 0 to 10 Volts (Default : 0 to 20mA)
Recorder Low	Min. to Max. Range specified for the selected Input Type (Default : -200)
Recorder High	Min. to Max. Range specified for the selected Input Type (Default : 1376)

INPUT CONFIGURATION PARAMETERS

Parameters	Settings (Default Value)
Input Type	Refer Table 2 (Default : Type K)
Units	Refer Table 1 (Default : ºC)
Signal Range Low	Input Type Settings Default 0 to 20 mA 0.00 to Signal High 0.00 4 to 20 mA 4.00 to Signal High 4.00 Reserved 0.0 to Signal High 0.0 0 to 80 mV 0.00 to Signal High 0.00 0 to 1.25 V 0.000 to Signal High 0.000 0 to 5 V 0.000 to Signal High 0.000 0 to 10 V 0.00 to Signal High 0.00 1 to 5 V 1.000 to Signal High 1.000
Signal Range High	Input Type Settings Default 0 to 20 mA Signal Low to 20.00 20 4 to 20 mA Signal Low to 20.00 20 Reserved Signal Low to 80.00 80 0 to 80 mV Signal Low to 80.00 80 0 to 1.25 V Signal Low to 1.250 1.25 0 to 5 V Signal Low to 5.000 5 0 to 10 V Signal Low to 10.00 10 1 to 5 V Signal Low to 5.000 5
Resolution	Refer Table 2 (Default : 1)
DC Range Low	-1999 to 9999 (Default : 0.0)
DC Range High	-1999 to 9999 (Default : 100.0)
Offset	-1999 to 9999 or -199.9 to 999.9 (Default : 0)
Filter	0.5 to 60.0 Seconds (in steps of 0.5 Seconds) (Default : 2.0 sec.)

SUPERVISORY PARAMETERS

Parameters	Settings (Default Value)
Alarm SP Adjustment on Operator Page	Disable Enable (Default : Disable)
Process Value High-Low Monitoring	No Yes (Default : No)
Password for Resetting PV High-Low	0 to 250 (Default : 0)
Serial ID Number	1 to 127 (Default : 1)
Baud Rate	4800 9600 19200 (Default : 9.6)
Parity	None Even Odd (Default : Even)
Serial Write Permission	No Yes (Default : Yes)

USER LINEARISATION PARAMETERS

Parameters	Settings (Default Value)
User Linearization Setting Code	0 to 9999 (Default : 0)
User Linearization	No Yes (Default : No)
Total Break Points	2 to 32 (Default : 2)
Break Point Number	1 to 32 (Default : 1)
Actual Value for Break Point (X co-ord)	-1999 to 9999 (Default : Undefined)
Derived Value for Break Point (Y co-ord)	-1999 to 9999 (Default : Undefined)

TABLE- 1

Lower Readout	Units
	°C	Temperature
	°F
	Kelvin
	Engineering Units
	Percentage
	Pascals	Pressure
	Mpascals
	Kpascals
	Bar
	Milli bar
	PSI
	kg/sq cm
	mm water gauge	Pressure
	Inches water gauge
	mm mercury
	Torr
	Litres per hour	Flow
	Litres per minute
	% Relative Humidity
	% O2
	% CO2
	% Carbon Potential
	volts	Electricity
	Amps
	Milli amps
	Milli Volts
	Ohms
	Parts per million
	Revolutions per pinute
	Milli seconds	Time
	Seconds
	Minutes
	Hours
	PH
	%PH
	Miles per hour
	Milli grams	Weight
	Grams
	Kilo grams

Lower Readout	Units
	mm (Millimeter)	Length/Height/Distance
	cm (Centimeter)
	Meter
	Kilometre
	Foot
	Inch
	Mile

Table 2

Option	What it means	Range (Min. to Max.)	Resolution
	Type J Thermocouple	0 to +960°C / +32 to +1760°F	Fixed 1°C/1°F
	Type K Thermocouple	-200 to +1376°C / -328 to +2508°F
	Type T Thermocouple	-200 to +385°C / -328 to +725°F
	Type R Thermocouple	0 to +1770°C / +32 to +3218°F
	Type S Thermocouple	0 to +1765°C / +32 to +3209°F
	Type B Thermocouple	0 to +1825°C / +32 to +3092°F
	Type N Thermocouple	0 to +1300°C / +32 to +2372°F
	Reserved for customer specific Thermocouple type not listed above. The type shall be specified in accordance with the ordered (optional on request) Thermocouple type.
	3-wire, RTD Pt100	-199 to +600°C/-328 to +1112°F or -199.9 to 600.0°C/-199.9 to 999.9°F	User settable 1°C/1°F or 0.1°C/0.1°F
	0 to 20mA DC current	-1999 to +9999 units	User settable 1 / 0.1 / 0.01/ 0.001 units
	4 to 20mA DC current
	Reserved
	0 to 80 mV DC voltage
	0 to 1.25V DC voltage
	0 to 5.0V DC voltage
	0 to 10.0V DC voltage
	1 to 5.0V DC voltage

FRONT PANEL LAYOUT

Keys Operation

Symbol	Key	Function
	PAGE	Press to enter or exit set-up mode.
	DOWN	Press to decrease the parameter value. Pressing once decreases the value by one count; keeping pressed speeds up the change.
	UP	Press to increase the parameter value. Pressing once increases the value by one count; keeping pressed speeds up the change.
	ENTER/ACK	Set up Mode: Press to store the set parameter value and to scroll to the next parameter on the PAGE. Run Mode: Press to acknowledge any pending Alarm(s). This also turns off the Alarm relay.

PV Error Indications

Message	PV Error Type
	Over-range (PV above Max. Range)
	Under-range (PV below Min. Range)
	Open (Sensor open/broken)

ELECTRICAL CONNECTIONS

101, Diamond Industrial Estate, Navghar,
Vasai Road (E), Dist. Palghar – 401 210.
Sales: 8208199048/8208141446
Support: 07498799226/08767395333
E: sales@ppiindia.net
support@ppiindia.net
Dec 2021

Documents / Resources

	PPI Neuro 200 Advanced Universal Process Indicator [pdf] Instruction Manual Neuro 200 Advanced Universal Process Indicator, Neuro 200, Advanced Universal Process Indicator, Universal Process Indicator, Process Indicator, Indicator
	PPI neuro 200 Advanced Universal Process Indicator [pdf] User Manual neuro 200 Advanced Universal Process Indicator, neuro 200, Advanced Universal Process Indicator, Universal Process Indicator, Process Indicator

References

• User Manual