Instruction Manual for CARAUDIO-SYSTEM models including: VW RNS315-Amundsen, RNS510-Columbus, RCD510, OBD-301-R Rear View Camera OBD Coder, OBD-301-R, Rear View Camera OBD Coder, View Camera OBD Coder, Camera OBD Coder, OBD Coder, Coder
Apr 5, 2024 · RNS510/Columbus navigation systems ... -7. Requirements. Vehicle. Audi, Skoda, Volkswagen. Navigation. RNS315/Amundsen and RNS510/Columbus ...
OBD-301-R Rear-view camera OBD-coder for VW RNS315/Amundsen, RNS510/Columbus navigation systems and RCD510 radio with 26pin connector as well as Audi MIB MMI Navigation, VW MIB Composition Media and Seat Media System Plus Delivery contents Take down the SW-version and HW-version of the interface boxes, and store this manual for support purposes. HW______________ SW______________ OBD-301-R Legal Information Changes/updates of the vehicle's software can cause malfunctions of the interface. We offer free software-updates for our interfaces for one year after purchase. To receive a free update, the interface must be sent in at own cost. Labor cost for and other expenses involved with the software-updates will not be refunded. Version 05.04.2024 OBD-301-R Check compatibility of vehicle and accessories Requirements Vehicle Navigation Limitations After-market rear-view camera PDC screen License Audi, Skoda, Volkswagen RNS315/Amundsen and RNS510/Columbus navigation systems RCD510 Radio/CD head-unit WITH 26pin connector on backside. MIB Composition Media, MIB MMI Navigation, Media System Plus Only compatible with NTSC-cameras. In some vehicles with MIB system, the PDC screen must be manually deactivated after automatic camera shutdown The OBD-coder can only be used in one vehicle (after use in a vehicle the using in other vehicles is blocked) Installation Vehicle with RNS315/Amundsen and RCD510 1. On RCD510 ensure that there is a 26pin connector on the rear 2. Locate OBD-port and remove cover 3. Turn on ignition (pos. 2, do not start engine) 4. Wait until the head-unit has booted 5. Plug coder into OBD-port 6. Leave coder for about 30 seconds in OBD-port 7. Remove coder from the OBD-port To reverse the coding repeat steps 2.-7. Vehicle with RNS510/Columbus 1. Locate OBD-port and remove cover 2. Turn on ignition (pos. 2, do not start engine) 3. Wait until the head-unit has booted 4. Plug coder into OBD-port, message "DIAG" is shown in the display 5. Leave coder for about 30 seconds in OBD-port 6. Remove coder from the OBD-port 7. A reset is necessary. Press buttons Tr+, Tr- and * together and hold them until the reset is done. To reverse the coding repeat steps 1.-7. Version 05.04.2024 OBD-301-R Vehicle with MIB Composition Media, MIB MMI Navigation and MIB Media System Plus 1. On RCD510 ensure that there is a 26pin connector on the rear 2. Locate OBD-port and remove cover 3. Turn on ignition (pos. 2, do not start engine) 4. Wait until the head-unit has booted 5. Plug coder into OBD-port 6. Leave coder for about 30 seconds in OBD-port 7. Remove coder from the OBD-port To reverse the coding repeat steps 2.-7. Note: After the first use on a vehicle, the coder OBD-301-R is personalized to this vehicle (head-unit) and can be used unlimited times to code or reverse coding on this vehicle. Rear-view camera video connection Vehicle with RNS315/Amundsen, RCD510 and RNS510/Columbus The video interface "RL-MFD3" is additionally required for these systems (available seperately). Vehicle with MIB Composition Media, MIB MMI Navigation and MIB Media System Plus The video cable included in the set is connected to the MIB Quadlock connector: Cable colour // Colored (video) Black (ground) Assignment Chamber B - Pin 6 Chamber B - Pin 12 Version 05.04.2024 OBD-301-R LED information: LED Blue Green Red Green + Red Status Flashes Lights Lights Flashes Lights Explication Coding process is running Coding procedure successfully completed Remove coding procedure successfully completed Coding process failed / license violation CAN Communication Error! - Abort of the diagnostic session Technical Support CAS GmbH Manufacturer / Distributor In den Fuchslöchern 3 D-67240 Bobenheim-Roxheim Email: support@casgermany.com Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered trademarks ® of their corresponding legal owners. Version 05.04.2024 OBD-301-RmacOS Version 13.5 (Build 22G74) Quartz PDFContext