Instrukcja obsługi

1. Wprowadzenie

This manual provides detailed instructions for the installation, operation, and maintenance of the IXITAB KWS-AC301/KWS-AC300 Digital AC Power Energy Meter. This device is designed to accurately measure and display AC voltage, current, active power, energy (kWh), and temperature. It is suitable for monitoring electrical parameters in various AC circuits.

2. Informacje dotyczące bezpieczeństwa

OSTRZEŻENIE: Electrical shock hazard. Installation and servicing should only be performed by qualified personnel. Failure to follow these instructions may result in serious injury or death.

• Ensure the power supply is disconnected before installation or wiring.
• Nie przekraczaj określonej objętościtage and current ratings (AC 50-300V, 100A).
• Nie używaj urządzenia w mokrym lub damp warunki.
• Trzymaj urządzenie z dala od materiałów łatwopalnych.
• Przed podłączeniem zasilania sprawdź, czy wszystkie połączenia są bezpieczne i prawidłowe.

3. Koniec produktuview

The KWS-AC301/KWS-AC300 meter features a clear digital display for simultaneous monitoring of multiple electrical parameters. It is compact and designed for easy integration into electrical panels or systems.

Figure 3.1: Product image placeholder. This image indicates that a specific product image is not available. The actual product is a compact digital meter designed for AC electrical measurements.

Główne cechy obejmują:

• Real-time measurement of AC Voltage (V), Current (A), Active Power (W), and Energy (kWh).
• Wyświetlacz temperatury.
• High accuracy and stability.
• Łatwy do odczytania wyświetlacz cyfrowy.

4. Konfiguracja i okablowanie

Before proceeding, ensure the main power supply is OFF.

1. Montowanie: Choose a suitable location for the meter, typically within an electrical panel or enclosure, ensuring adequate ventilation.
2. Tomtage Input (L/N): Podłącz obj. ACtage input wires to the designated L (Live) and N (Neutral) terminals on the meter. Ensure the voltage mieści się w zakresie 50-300 V prądu przemiennego.
3. Podłączenie przekładnika prądowego (CT):
   • Pass the load wire (the wire carrying the current you wish to measure) through the hole of the external current transformer (CT).
   • Connect the two small wires from the CT to the dedicated CT input terminals on the meter. Pay attention to polarity if indicated, though many simple CTs are non-polar for measurement.
4. Załaduj połączenie: Ensure the load is correctly connected to the circuit being monitored.
5. Włączanie: After all connections are verified and secure, restore power to the circuit. The meter should power on and display readings.

Note: The CT must be connected before applying power to the meter to avoid damage. Do not disconnect the CT while power is applied to the meter.

5. Instrukcja obsługi

Once powered on, the KWS-AC301/KWS-AC300 meter will automatically begin displaying the measured parameters. The display typically cycles through or shows simultaneously:

• Tomtage (v): Displays the current AC voltage.
• Prąd (A): Displays the current AC amperage flowing through the monitored circuit.
• Moc czynna (W): Displays the instantaneous active power consumed by the load.
• Energia (kWh): Accumulates the total energy consumed over time. This value is typically non-volatile and retained even after power loss.
• Temperatura (°C/°F): Displays the ambient temperature measured by the device.

Some models may include a button for resetting the energy (kWh) reading. If present, press and hold the button for approximately 5 seconds to clear the accumulated energy data. Refer to specific product markings for button functionality.

6. Konserwacja

The KWS-AC301/KWS-AC300 meter requires minimal maintenance.

• Czyszczenie: Do czyszczenia wyświetlacza i obudowy należy używać miękkiej, suchej ściereczki.asing. Nie należy używać środków czyszczących o właściwościach ściernych ani rozpuszczalników.
• Kontrola: Okresowo sprawdzaj połączenia przewodów, aby mieć pewność, że są bezpieczne.
• Składowanie: If storing the device for an extended period, keep it in a dry, cool environment, away from direct sunlight and extreme temperatures.

7. Rozwiązywanie Problemów

8. Specyfikacje

9. Gwarancja i wsparcie

This product is manufactured by IXITAB. For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly through the platform where the product was purchased. Please have your purchase details and product model number (KWS-AC301/KWS-AC300) ready when contacting support.

For further assistance, you may refer to the product listing on Amazon.com.