Fengda Mini Airbrush Compressor FD-18-2 User Manual

1. Wprowadzenie

Thank you for choosing the Fengda Mini Airbrush Compressor FD-18-2. This oil-free piston compressor is designed for various applications, including airbrushing, cosmetics, nail art, tattoos, hobbies, and home use. Its compact size and low noise level make it suitable for both professional and personal environments. Please read this manual thoroughly before operation to ensure safe and efficient use.

2. Instrukcje bezpieczeństwa

OSTRZEŻENIE: Nieprzestrzeganie tych instrukcji bezpieczeństwa może spowodować porażenie prądem, pożar lub poważne obrażenia.

• Zawsze upewnij się, że zasilanie jest zgodne z napięciemtage specified on the compressor (220-240V / 50Hz).
• Do not operate the compressor in wet conditions or near flammable liquids or gases.
• Trzymać dzieci i osoby nieupoważnione z dala od obszaru roboczego.
• Always disconnect the power plug before performing any maintenance or cleaning.
• Nie modyfikuj sprężarki ani jej podzespołów. Używaj wyłącznie oryginalnych części zamiennych.
• Ensure adequate ventilation during operation to prevent overheating. The compressor has thermal protection, but proper airflow is crucial.
• Never direct the air stream at people or animals.
• Wear appropriate personal protective equipment, such as eye protection, when operating the airbrush system.
• The compressor is designed for intermittent use. Avoid continuous operation for extended periods to prevent overheating.

3. Koniec produktuview

The Fengda FD-18-2 is a compact, oil-free piston compressor featuring a pressure regulator, filter, and manometer for precise control and clean air delivery. It is designed for quiet operation and portability.

3.1 Zawarte komponenty

• 1 x Fengda FD-18-2 Mini Airbrush Compressor (without air tank)
• 1 x Output Pressure Regulator with Filter and Manometer
• 1 x kabel zasilający
• 1 x Instrukcja obsługi

3.2 Główne cechy

• Oil-free piston design ensures clean air without oil contamination.
• Integrated pressure regulator with filter and manometer for precise pressure adjustment and moisture separation.
• Automatic start at 3 bar (43.5 PSI) and automatic stop at 4 bar (58 PSI) for efficient operation.
• Thermal protection against overload or overheating.
• Low noise level (47 dB) for comfortable use in various environments.
• Portable and lightweight design with rubber feet for stability.
• Suitable for airbrushes with nozzle sizes from 0.2 mm to 1.0 mm.
• Ideal for model painting, body painting, nail art, fine arts, car painting, touch-ups, cake decorating, textile and t-shirt painting, or other painting applications.

Rysunek 1: Koniecview of the Fengda FD-18-2 Mini Airbrush Compressor, showing the main unit, pressure regulator, filter, and power cable.

4. Konfiguracja i instalacja

1. Rozpakowywanie: Ostrożnie wyjmij wszystkie elementy z opakowania. Sprawdź, czy nie uległy uszkodzeniu podczas transportu.
2. Umieszczenie: Place the compressor on a stable, flat surface. Ensure the rubber feet are securely positioned to minimize vibration. Allow sufficient space around the unit for proper ventilation.
3. Podłącz regulator: The pressure regulator with filter and manometer typically comes pre-attached or needs to be screwed onto the air outlet port of the compressor. Ensure it is hand-tightened securely to prevent air leaks.
4. Connect Airbrush Hose: Connect your airbrush hose to the G 1/8" air outlet thread on the pressure regulator. Ensure a tight connection.
5. Podłączenie zasilania: Plug the power cable into a suitable grounded electrical outlet (220-240V / 50Hz).

Rysunek 2: Szczegółowy view of the pressure regulator, filter, and manometer, essential for controlling air pressure and ensuring clean air.

5. Działanie

1. Włączanie: Flip the power switch to the "ON" position. The compressor will start and build pressure until it reaches approximately 4 bar (58 PSI), then it will automatically shut off.
2. Dostosuj ciśnienie: Use the knob on the pressure regulator to adjust the desired working pressure. Turn clockwise to increase pressure, counter-clockwise to decrease. The manometer will display the current output pressure.
3. Begin Airbrushing: Once the desired pressure is set, you can begin using your airbrush. The compressor will automatically restart when the pressure drops to approximately 3 bar (43.5 PSI) and stop again when it reaches 4 bar (58 PSI).
4. Moisture Trap: The integrated filter acts as a moisture trap. Periodically check the transparent bowl for accumulated moisture.
5. Wyłączone: When finished, turn off the compressor using the power switch and disconnect it from the power outlet.

Rysunek 3: Zbliżenie view of the manometer, indicating the adjustable air pressure output.

6. Konserwacja

Regularna konserwacja zapewnia długowieczność i optymalną wydajność sprężarki.

• Drain Moisture Trap: Regularly check and drain any accumulated moisture from the filter/moisture trap. This prevents water from reaching your airbrush and paint. To drain, unscrew the small valve at the bottom of the transparent bowl.
• Czysty wygląd zewnętrzny: Wytrzyj zewnętrzną część kompresora za pomocąamp płótno. Nie używaj ostrych środków chemicznych ani ściernych środków czyszczących.
• Filtr powietrza: The compressor has an internal air filter. While not user-serviceable in the same way as the moisture trap, ensure the air intake vents are clear of dust and debris.
• Składowanie: When not in use, store the compressor in a clean, dry, and dust-free environment.

7. Rozwiązywanie Problemów

8. Specyfikacje

9. Gwarancja i wsparcie

This product is covered by a standard manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions. For technical support, spare parts, or warranty claims, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Manufacturer: Fenghua Bida Machinery Manufacture CO., LTD