Fengda FD-196 Mini Airbrush Compressor User Manual

1. Wprowadzenie i produkt końcowyview

The Fengda FD-196 is an oil-free, dual-piston mini airbrush compressor designed for a wide range of applications, from hobbyist model painting to professional nail art and cosmetics. It features a 3.5-liter air tank, automatic stop function, and a maximum pressure of 6 bar, ensuring consistent and pulsation-free air delivery. Its quiet operation and integrated water filter and pressure regulator make it a versatile and reliable tool.

Główne cechy:

• Oil-free dual-piston design.
• 3.5L air tank for stable pressure.
• Automatic start/stop function (Level 1: 2.8 bar start, 4 bar stop).
• Maximum pressure of 6 bar (Level 2).
• Low noise level (approximately 45-55 dB).
• Integrated pressure regulator with manometer and water filter.
• Zabezpieczenie przed przegrzaniem.
• Supports simultaneous operation of two airbrushes.

Rysunek 1: Ogólnie view of the Fengda FD-196 Mini Airbrush Compressor, showing the main unit, air tank, pressure regulator, and air outlets.

Figure 2: Close-up of the solenoid valve, which contributes to the smooth start-up of the compressor.

2. Instrukcje bezpieczeństwa

Please read all safety instructions carefully before operating the compressor. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Always ensure the compressor is placed on a stable, level surface in a well-ventilated area.
• Do not operate the compressor near flammable liquids, gases, or dust.
• Upewnij się, że napięcie zasilaniatage matches the specifications on the compressor's label (220 Volts).
• Never touch the compressor with wet hands or while standing in water.
• Unplug the compressor from the power outlet before performing any maintenance, cleaning, or when not in use.
• Nie modyfikuj sprężarki ani jej podzespołów. Używaj wyłącznie oryginalnych części zamiennych.
• Trzymaj dzieci i zwierzęta domowe z dala od pracującego kompresora.
• Nie kieruj strumienia powietrza na ludzi i zwierzęta.
• Regularly drain condensation from the air tank to prevent corrosion and maintain performance.
• The compressor is equipped with an overheat protection system. If it shuts down due to overheating, allow it to cool down before restarting.
• The safety valve is designed to release pressure if it exceeds 6 bar. Do not tamper with or block this valve.

Rysunek 3: Zbliżenie view of the safety labels and the drain valve located at the bottom of the air tank. Always observe safety warnings and drain condensation regularly.

3. Zawarte komponenty

Po rozpakowaniu należy sprawdzić, czy znajdują się w nim wszystkie poniższe elementy:

• 1x Fengda FD-196 Airbrush Compressor with 3.5L Air Tank
• 1x Pressure Regulator Outlet with Integrated Filter and Manometer
• 1x Kabel zasilający
• 1x Instrukcja obsługi (ten dokument)

Rysunek 4: Example of the protective styrofoam packaging used to secure the compressor during transport. Please ensure all components are removed from packaging before setup.

4. Konfiguracja

1. Rozpakowywanie: Carefully remove the compressor and all accessories from the packaging. Inspect for any damage that may have occurred during transit.
2. Umieszczenie: Position the compressor on a firm, level, and stable surface. Ensure there is adequate ventilation around the unit to prevent overheating. Keep it away from direct sunlight, heat sources, and moisture.
3. Attach Pressure Regulator: Screw the pressure regulator outlet (with filter and manometer) onto the designated air outlet port of the compressor. Ensure it is hand-tightened securely to prevent air leaks.
4. Connect Airbrush Hose: Connect your airbrush hose to the outlet of the pressure regulator. The hose fitting diameter is typically 1/8".
5. Podłączenie zasilania: Ensure the compressor's power switch is in the "OFF" position. Plug the power cable into a grounded electrical outlet (220 Volts).

5. Instrukcja obsługi

The FD-196 compressor features a dual-level switch for flexible operation modes.

1. Włączanie: Flip the main power switch to the desired operating level.
2. Tryby pracy:
   • Level 1 (Automatic Stop Mode): In this mode, the compressor will automatically start when the pressure drops to 2.8 bar and stop when it reaches 4 bar. This mode is ideal for most airbrushing tasks, providing consistent pressure and reducing wear on the motor.
   • Level 2 (Maximum Pressure Mode): In this mode, the compressor will run continuously until it reaches its maximum pressure of 6 bar. A safety valve will automatically release pressure if it exceeds 6 bar. This mode is suitable for tasks requiring higher, sustained pressure.
3. Regulacja ciśnienia: Use the knob on the pressure regulator to adjust the working pressure. The manometer will display the current output pressure. Adjust the pressure according to your airbrush and paint requirements. The effective continuous working pressure range is 0.35 to 2.5 bar.
4. Zabezpieczenie przed przegrzaniem: The compressor is equipped with thermal overload protection. If the unit becomes too hot during prolonged use, it will automatically shut down. Allow it to cool down completely before attempting to restart.
5. Dual Airbrush Support: The compressor is designed to support two airbrushes operating simultaneously, provided the combined air demand does not exceed the compressor's capacity.
6. Wyłączone: After use, switch the compressor to the "OFF" position and unplug it from the power outlet.

Figure 5: Close-up of the main power switch, which allows selection between automatic stop mode (Level 1) and maximum pressure mode (Level 2).

6. Konserwacja

Regularna konserwacja zapewnia długowieczność i optymalną wydajność sprężarki.

• Odpływ kondensatu: After each use, or at least daily, drain any accumulated condensation from the air tank. This is crucial to prevent internal corrosion. Locate the drain valve at the bottom of the air tank (refer to Figure 3), place a container underneath, and open the valve until all water is expelled. Close the valve securely afterward.
• Filtr czystego powietrza: Periodically check and clean the air filter on the pressure regulator. A clogged filter can reduce airflow and efficiency. Refer to the regulator's specific instructions for cleaning or replacing the filter element.
• Ogólne sprzątanie: Przetrzyj zewnętrzną część sprężarki za pomocąamp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure the compressor is unplugged before cleaning.
• Składowanie: When storing the compressor for extended periods, ensure the air tank is drained and the unit is clean and dry. Store in a cool, dry place.

7. Rozwiązywanie Problemów

8. Specyfikacje

9. Gwarancja i wsparcie

Aby uzyskać informacje o gwarancji i pomocy technicznej, zapoznaj się z dokumentacją dołączoną do zakupu lub skontaktuj się bezpośrednio ze sprzedawcą lub producentem. Zachowaj dowód zakupu na wypadek roszczeń gwarancyjnych.