Thermaltake Contac 21 Universal CPU Cooler

1. Koniec produktuview

The Thermaltake Contac 21 Universal CPU Cooler (CLP0600) is designed to provide efficient cooling for various CPU platforms. It features Direct-Touch Heat Transfer Technology with four 6mm copper heatpipes that make direct contact with the CPU, enhancing thermal transfer efficiency. The cooler includes one 92mm PWM fan and supports an additional 92mm fan for increased performance. It is compatible with Intel LGA-1366/1155/1156/775 and AMD FM1/AM3+/AM3/AM2+/AM2 sockets, supporting CPUs with a Thermal Design Power (TDP) up to 140W.

Figure 1: Thermaltake Contac 21 Universal CPU Cooler. This image shows the heatsink with its fins and heatpipes, and the attached 92mm PWM fan.

2. Informacje dotyczące bezpieczeństwa

• Przed instalacją lub konserwacją należy zawsze odłączyć komputer od zasilania.
• Ostrożnie obchodź się z elementami, aby uniknąć ich uszkodzenia. Na żeberkach radiatora mogą znajdować się ostre krawędzie.
• Przechowywać w miejscu niedostępnym dla dzieci.
• Zadbaj o odpowiednią wentylację wnętrza obudowy komputera.
• Do not operate the CPU without a properly installed cooler.

3. Zawartość opakowania

Sprawdź, czy w opakowaniu znajdują się wszystkie elementy:

• Thermaltake Contac 21 Heatsink
• 92mm PWM Fan (x1)
• Fan Mounting Clips (for one or two fans)
• Universal Mounting Kit (backplate, brackets, screws, spacers)
• Thermal Grease (pre-applied or in a small tube)
• Instrukcja obsługi (ten dokument)

4. Konfiguracja i instalacja

Ważny: Installation requires access to the rear of the motherboard. In some computer cases, the motherboard may need to be removed to install the backplate. Refer to your computer case manual for details on motherboard access.

Ogólne kroki instalacji:

1. Przygotuj procesor: Ensure the CPU socket is clean. If replacing an old cooler, carefully clean off any old thermal paste from the CPU surface using isopropyl alcohol.
2. Nałóż pastę termoprzewodzącą: If thermal grease is not pre-applied to the cooler's base, apply a small, pea-sized amount to the center of the CPU's integrated heat spreader (IHS). Do not spread it manually; the pressure from the cooler will distribute it evenly.
3. Montaż płyty tylnej: Position the universal backplate on the rear side of the motherboard, aligning the holes with the CPU socket mounting holes.
4. Zamocuj wsporniki montażowe: On the front side of the motherboard, place the appropriate mounting brackets (Intel or AMD) over the CPU socket, aligning them with the backplate screws. Secure them loosely with the provided standoffs/screws.
5. Montaż radiatora: Carefully place the heatsink onto the CPU, ensuring the heatpipes make direct contact. Align the heatsink's mounting holes with the brackets.
6. Bezpieczny radiator: Using the provided screws, alternately tighten the screws in a diagonal pattern until the heatsink is firmly seated. Nie dokręcaj zbyt mocno. Ensure even pressure.
7. Podłącz wentylator: Use the included fan clips to attach the 92mm PWM fan to the heatsink. Ensure the fan is oriented to blow air through the heatsink fins towards the rear or top of the case.
8. Podłącz kabel wentylatora: Plug the 4-pin PWM fan connector into the CPU_FAN header on your motherboard.
9. Optional Second Fan: If installing a second 92mm fan (not included), use the additional fan clips and connect it to an available fan header on your motherboard (e.g., CHA_FAN or SYS_FAN).

Uwagi dotyczące konkretnej platformy:

• Intel LGA775/1156/1155/1366: Use the Intel-specific mounting brackets and hardware. Ensure the backplate is correctly oriented for your socket type.
• AMD FM1/AM3+/AM3/AM2+/AM2: Use the AMD-specific mounting brackets and hardware. Some users have reported challenges with AMD instructions; proceed carefully, ensuring all components fit without excessive force. If issues arise, double-check component alignment and consult online resources for visual guides specific to your motherboard and CPU socket.

5. Instrukcja obsługi

Once installed, the Thermaltake Contac 21 operates automatically. The 92mm PWM fan's speed is controlled by your motherboard based on CPU temperature, ensuring optimal cooling performance while minimizing noise.

• Początkowy rozruch: After installation, power on your computer and enter the BIOS/UEFI settings. Verify that the CPU fan is detected and spinning. Monitor CPU temperatures during initial operation.
• Monitorowanie temperatury: Use motherboard monitoring software or third-party utilities to keep track of your CPU temperature, especially under load, to ensure the cooler is functioning effectively.
• Kontrola prędkości wentylatora: Most motherboards allow customization of PWM fan curves in the BIOS/UEFI. You can adjust these settings to prioritize quieter operation or maximum cooling performance as desired.

6. Konserwacja

Regularna konserwacja pomaga zapewnić długowieczność i optymalną wydajność chłodzenia procesora.

• Usuwanie kurzu: Periodically (every 3-6 months, depending on environment) use compressed air to blow dust out of the heatsink fins and fan blades. Hold the fan blades gently to prevent over-spinning during cleaning, which can damage the fan motor.
• Kontrola wentylatora: Check the fan for any signs of wear, unusual noise, or obstructions. Ensure the fan cable is securely connected.
• Smar termiczny: The thermal grease typically lasts for several years. If you notice a significant increase in CPU temperatures over time, consider reapplying fresh thermal grease. This requires removing the cooler, cleaning both surfaces, and applying new paste.

7. Rozwiązywanie Problemów

8. Specyfikacje

9. Gwarancja i wsparcie

Thermaltake products are manufactured to the highest quality standards. This product is covered by a limited warranty from the date of purchase. Please refer to the official Thermaltake webAby zapoznać się ze szczegółowymi warunkami gwarancji obowiązującymi w Twoim regionie, odwiedź naszą witrynę.

For technical support, troubleshooting assistance, or warranty claims, please visit the official Thermaltake support website or contact their customer service department. Have your product model number (CLP0600) and proof of purchase ready when contacting support.

Urzędnik Webstrona: www.thermaltake.com

10. Zasoby wideo

No official product videos from the seller were available in the provided data for embedding. Please refer to the manufacturer's official website or YouTube channel for any available video guides or demonstrations.