PNX12-10001 Touch Panel Controlmini
User Manual
Controlmini and Gira DCS
Getting started
| Created for use with the following product | Item number |
| Controlmini | PNX12-10001 |
Introduction
The following instructions explain how to set up a Gira door station with your PEAKnx touch panel.
Audioassistant of the TKS Communicator
- Select audio components
− Select the „Microphone and Loudspeaker“ option.
- Adjusting the volume
− Start the volume test and adjust the slider to your needs. By default a position in the middle is recommended.
- Select recording device
− Select the option „Microphone (Intel SST Audio Device(WDM))“ here.
- Adjusting the microphone volume
− Do the speech test and move the slider to the second line from the right.
− Select „Settings“ at the bottom of the window.
− In the next window double-click on the microphone with the green tick.
− Here you can now set the gain under the „Level“ tab.
− Adjust the microphone volume (Microphone) to the middle.
− Set the microphone boost to +12.0 dB.
− Accept the settings and close the window to continue with the wizard.
■ Calibrate microphone volume
− Press the „Start“ button and adjust the slider to the middle.
■ Optimize voice quality
− Perform the voice quality test. - Optimize microphone volume
− Move the slider to the second line from the right.
- Test configuration
− Start the configuration test. - Finish Audio Assistant
− Close the audio assistant and have fun with your Controlmini intercom!
Troubleshooting
| Problem | Solution |
| After a few seconds of good intelligibility on the door unit, the person on the PEAKnx Panel is suddenly perceived quiet and barely audible or cut off and hard to hear. | Microphone is amplified too much, see point 4 Microphone volume. Reduce microphone volume slightly or reduce microphone level slightly (slider to the left) |
| At the door unit, the person at the PEAKnx Panel is perceived at the correct volume but with white noise in the background. | The wizard amplifies the microphone of the PEAKnx Panel too much, see point 5 Optimize microphone volume. Reduce the microphone volume (slider to the left) |
| At the door unit, the person at the PEAKnx Panel is perceived too quiet. | The microphone is not amplified enough, see point 4 Microphone volume. Increase the microphone volume (slider to the right) |
Display TKS Communicator larger
■ Right-click on the TKS Communicator shortcut and select Properties.
■ Switch to the Compatibility tab.
■ Click on Change high DPI settings.
■ Check Override high DPI scaling behavior and select “System (Advanced)” from the dropdown menu below it.
■ Confirm with “Ok” in both windows.
When the bell is pressed, switch on the screen via the Gira Home Server
■ Create TKS IP gateway:
■ Create internal KOs (communication objects):
■ IP/EIB telegrams (send):
*Receiver (Empfänger): IP/Host-Address: IP address of the panel
*Send (Senden): Text (Text): TecTool command. To learn more about TecTool, click here.
■ Create logic:
Technical Support
If you experience problems with your PEAKnx Panel please contact our PEAKnx Support Team:
− Mail: support@peaknx.com
− Create a Support Ticket: support.peaknx.com/?lang=en_US
− Tel.: +49-6151-279 1825
The product names mentioned in this document may be brands or registered trademarks of their respective owners. These are not explicitly labeled with “™” or “®”.
© PEAKnx GmbH
Otto-Röhm-Strasse 69
64293 Darmstadt
Germany
www.peaknx.com
info@peaknx.com
Document version: 2.1.0
Date: 17.05.22
Documents / Resources
 | PEAKnx PNX12-10001 Touch Panel Controlmini [pdf] User Manual PNX12-10001 Touch Panel Controlmini, PNX12-10001, Touch Panel Controlmini, Panel Controlmini |
