Once you connect the Joy-Con Charging Shuttle to a power source, the LED indicators on the top of the charging shuttle will turn on and begin flashing. The individual charging indicators let you know the charge status of each Joy-Con controller. Once fully charged, the lights will remain solid.

INSTALLING & CHARGING THE JOY-CON CONTROLLERS

To set up your Joy-Con Charging Shuttle, connect the USB cable to the Nintendo Switch Dock, or any other USB port.
Once connected, the LED charging indicators on top of the charging shuttle will flash 3 times, indicating “ready” status.

Line up the Joy-Con controllers with the rails on the charging shuttle and carefully slide them down until they can’t go any further.

The LED charging indicators will light up and begin breathing to indicate the Joy-Con controllers are properly installed.

When charging, the LED indicators will show the charge status of each respective Joy-Con controller.
The LED charging indicators will remain solid when fully charged.

REMOVING THE JOY-CON CONTROLLERS

To remove a Joy-Con controller from the Joy-Con Charging Shuttle, simply pull the controller up and out.

CLASS B EQUIPMENT

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

FCC

These limits are designed to provide reasonable protection against harmful interference in a residential installation. Ihis equipment generates, uses and can radiate radio frequency energy and, it not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is Connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

2.YEAR LIMITED MANUFACTURER’S WARRANTY

Coverage and Terms

PDP warrants that this product will be free from manutacturing detects for two years from the original date of purchase. Manutacturing defects are those defects in materials and/or workmanship, subject to final determination by PDP’s customer service department. This warranty applies only to original purchasers with a valid proof of purchase from an authorized PDP retailer that clearly shows the date of purchase.

Exclusive Remedy and Exclusions

The excdusive remedy for valid claims wil be the repair, replacement, or retund of the product. This warranty does not cover defects caused by accidents, improper or abusive use of the product, unauthorized or improper modifications, repairs, or handling.

How to Get Service

Purchasers with product issues should not return the product to the store, but instead contact PDP’s customer service department first. You can contact PDP customer service by phone at 1-800-331-3844 (US and Canada only), Monday to Friday from 8 AM to 6 PM PST. International Customers can contact us by phone at +442036957905. You can always reach us, 24/7, by visiting support.pdp.com and clicking the “Submit a Request” button top right of the page to open a support ticket Inquiries are tvoically answered within 24 husiness hours

Your Rights Under Applicable Law

Ihis warranty does not affect the legal rights of customers under applicable state, provincial, or national laws governing the sale of consumer goods.

Additional Information for Australian Consumers

PDP products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or retund tor a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Ihe benetits given to you under our express warranty are in addition to other rights and remedies you have under the Australian Consumer Law and other laws.

© 2021 Performance Designed Products LLC. PDP, PDP Gaming, Level Up Your Game, and their respective logos are trademarks and/or registered trademarks of Performance Designed Products LLC. All rights reserved. © 2021 Nintendo. Nintendo Switch is a trademark of Nintendo. Licensed by Nintendo. All rights reserved. All other logos and trademarks are the property of their respective owners. Please keep this information for future reference.

For Australia Only: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

This product is manufactured and imported by Performance Designed Products Ltd.

Performance Designed Products LLC. 4225 W Buckeye Rd #2, Phoenix, AZ 85009, USA support.pdp.com

Documents / Resources

pdp gaming NS 500-188 Joy-Con Charging Shuttle for Nintendo Switch [pdf] User Guide
NS 500-188 Joy-Con Charging Shuttle for Nintendo Switch, NS 500-188, Joy-Con Charging Shuttle for Nintendo Switch, Shuttle for Nintendo Switch, Nintendo Switch