pdp gaming 500-180 Controller Mount Nintendo Switch Grey User Guide

 pdp gaming 500-180 Controller Mount Nintendo Switch Grey User Guide

Items Included with the Joy-Con Charging Grip Plu

• Lighting Feature
• Getting Started
  • Installation
  • Charging
  • Removal
• 2-Year Limited Manufacturer’s Warranty Information

A: Charging Grip

B: USB Type C Charging Cable

C: Quick Start Guide

Once you connect the Joy-Con Charging Grip Plus to a power source, the LED indicators on the bottom of the grip will turn on and begin flashing. The individual charging indicators let you know the charge status of each Joy-Con controller. Once fully charged, the lights will remain solid.

Installation

Follow the steps below to install your Joy-Con controllers into the Joy-Con Charging Grip Plus:

• Take the empty grip out of the box and locate the latch on the top.
• Slide it to the right to release the hatch.
• Take a Joy-Con controller and align the rail on the side with the groove on the inside of the grip.
• Slide down until the bottom of the controller is flush with the bottom of the charging grip.
• Repeat these steps with the other Joy-Con controller.
• Once both controllers are in the grip, lift the hatch up towards you and then press the hatch down until you hear a small click. The Joy-Con controllers will then be secured in the grip and ready to use.
  

Charging

To charge your Joy-Con controllers using the Joy-Con Charging Grip Plus, ensure both controllers are secured in the grip and simply connect the included USB Type C cable into the charging port (located on top of the grip). Then, plug the other end of the USB Type C cable into a USB port. The LED Charging indicators will begin blinking and show the respective charge status of each Joy-Con controller

Removal

Follow the steps below to remove your Joy-Con controllers from the Joy-Con Charging Grip Plus:

• Slide the latch, on top of the charging grip, to the right and then push the hatch down.
• Push the controllers halfway up from the bottom, then pull the rest of the way out from the top.
• Repeat these steps to remove the other Joy-Con controller.
  

CLASS B EQUIPMENT

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that  to which the receiver is Connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

LIMITED WARRANTY

Coverage and Term PDP warrants that this product will be free from manufacturing defects for two years from the original date of purchase. Manufacturing defects are those defects in materials and/or workmanship, subject to final determination by PDP’s customer service department. This warranty applies only to original purchasers with a valid proof of purchase from an authorized PDP retailer that clearly shows the date of purchase.
Exclusive Remedy and Exclusions The exclusive remedy for valid claims will be the replacement, or refund of the product. This warranty does not cover defects caused by accidents, improper or abusive use of the product, unauthorized or improper modifications, repairs, or handling
How to Get Service

Purchasers with product issues should not return the product to the store, but instead contact PDP’s customer service department first. You can contact PDP customer service by phone at 1-800-331-3844 (US and Canada only), Monday to Friday from 8 AM to 6 PM PST. International customers can contact us by phone at +442036957905. You can always reach us, 24/7, by visiting support.pdp.com and clicking the “Submit a Request” button top right of the page to open a support ticket. Inquiries are typically answered within 24 business hours.
Your Rights Under Applicable Law This warranty does not affect the legal rights of customers under applicable state, provincial, or national laws governing the sale of consumer goods.
Additional Information for Australian Consumers PDP products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits given to you under our express warranty are in addition to other rights and remedies you have under the Australian Consumer Law and other laws.

2-Year Manufacturer’s Warranty: For product issues and guidance contact us instead of returning to the store.

Documents / Resources

pdp gaming 500-180 Controller Mount Nintendo Switch Grey [pdf] User Guide 500-180 Controller Mount Nintendo Switch Grey, 500-180, Controller Mount Nintendo Switch Grey, Nintendo Switch Grey, Switch Grey

References

• Patents
• PDP - Licensed Xbox, Switch, PlayStation and PC Controllers & Headsets