8Bitdo SF30 / SN30 2.4G User Manual

SN30 2.4G and SF30 2.4G

Instruction Manual

SN30 2.4G and SF30 2.4G

Connection

NES/SNES/SFC Classic Edition (wireless connection)

1. Plug the 2.4G Retro Receiver into your NES / SFC / SNES Classic Edition.
2. Press START on your controller to connect to the Retro Receiver.
3. LED will be solid blue when connection is successful.

Home Menu Access for NES/SNES/SFC Classic Edition.
SELECT + DOWN = RESET

If connection is lost or you wish to pair with a new retro receiver, press and hold SELECT on the

controller for 3 seconds. Blue LED will rapidly blink and be solid blue when connection is successful

Windows/macOS/Android (wired connection)

1. Connect the controller to your Windows/macOS/Android via the USB cable.
2. LED will be solid blue when connection is successful.
X-Input: press and hold START+X for 3 seconds, blue LED blinks twice to indicate mode activation.
D-Input: press and hold START+B for 3 seconds, blue LED blinks twice to indicate mode activation.
macOS: press and hold START+A for 3 seconds, blue LED blinks twice to indicate mode activation.
Default mode: D-input.

Status LED indicator
Low battery mode POWER LED in Red
Battery Charging POWER LED in green
Battery fully charged POWER LED turns off

Built-in 180 mAh Li-on with 25 Hours of play time.
Rechargeable via USB cable with 60 minutes charging time.

Power Saving

Sleep mode – 15 minutes with wireless connection but no use.

Support

Please visit support.8bitdo.com for further information and additional support.

 

8Bitdo N30 Pro / F30 Pro User Manual

N30 Pro and F30 Pro

Instruction Manual

Bluetooth Connection

Controllers will auto reconnect to your devices once they have been paired

Android (D-input)

1. Press and hold POWER for 1 second to power on the controller, LEDs will blink once per cycle.
2. Press and hold PAIR for 3 seconds to enter pairing mode. Blue LEDs will rapidly blink.
3. Go to your Android device’s Bluetooth setting, pair with [8Bitdo xx Pro].
4. LEDs will be solid blue when connection is successful.
USB Connection:connect your 8Bitdo controller to your Android device via USB Cable after step 1

Windows (X-input)

1. Press and hold POWER + X for 1 second to power on the controller, LEDs will blink twice per
cycle.
2. Press and hold PAIR for 3 seconds to enter pairing mode. Blue LEDs will rapidly blink.
3. Go to your Windows device’s Bluetooth setting, pair with [8Bitdo xx Pro(x)].
4. LEDs will be solid blue when connection is successful.
USB Connection:connect your 8Bitdo controller to your Android device via USB Cable after step1

macOS

1-Press and hold POWER + A for 1 second to power on the controller,
LEDs will blink three times per cycle
2-Press and hold PAIR for 3 seconds to enter pairing mode.Vlue LEDs will rapidly blink
3-Go to your macOS device’s Bluetooth setting ,pair with [Wireless Controller]
4-LEDs will be solid blue when connection is successful.
.USB connection : connect your 8Bitdo controller to your macOS device via USB cable after step1

Switch (by default)

1.press and hold POWER+Y for 1 second to power on the controller,
LEDs will blink four times per cycle

2.Go to your Switch Home Page to click on Controllers,then click on Change Grip/Order
3.Press and hild PAIR for 3 seconds to enter pairing mode.Blue LEDs will rapidly blink
4.LEDs will be solid blue when connection is successful
.When Connected to your Switch ,POWER button = Switch HOME button;
PAIR button = Switch screenshot button

Battery

Status LED indicator
Low battery mode LEDS blink in red
Battery Charging LEDS blink in Green
Battery fully charged LEDs stop blinking in green
  • Built-in 480 mAh Li-on with 18 Hours of play time.
  • Rechargeable via USB cable with 1-2 hour charging time.
  • Press POWER for 8 seconds to force turn off your controller

Power Saving

  1. Sleep mode -1 minute with no bluetooth connection
  2. sleep mode – 15 minutes with Bluetooth connection but no use
  3. Press POWER to wake up your controller

Support

.Please visit http://support.8bitdo.com for further information and additional support

 

8Bitdo N30 Arcade Stick User Manual

N30 Arcade Stick

Instruction Manual

N30 Arcade Stick

Bluetooth Connection

N30 Arcade Stick will auto reconnect to your devices once it has been successfully paired.

Android (D-Input)

1. Select DINPUT MODE via DINPUT/XINPUT Switch, then press START to power on the joystick.
Blue LED will blink once per cycle
2. Press and hold PAIRING button for2 seconds to enter pairing mode Blue LED wil rapidly blink.
3. Enter your device’s Bluetooth setting to pair with [8Bitdo x Arcadel. LED will be solid blue
when connection is successful.

Windows (X-Input)

1. Select XINPUT MODE via DINPUT/XINPUT switch, then press START to power on the joystick.
Blue LED will blink twice per cycle.
2. Press and hold PAIRING button for 2 seconds to enter pairing mode. Blue LED will rapidly blink.
3. Enter your devices Bluetooth setting to pair with [8Bitdo & Arcade(x]. LED will be solid
blue when connection is successful.

.USB Connection: connect your N30 Acade Stick to your Windows device via USB Cable after step 1
.D-input and X-input modes can be interchanged while playing.

macOS

1. Press and hold START + Ato power on the joystick. Blue LED will blink three time per cycle.
2. Press and hold PAIRING button for 2 seconds to enter pairing mode. Blue LED will rapidly blink.
3. Enter your device’s Bluetooth setting to pair with [Wireless Controller]. LED will be solid blue.
when connection is successful.

• USB Connection: connect your N30 Acade Stick to your macOS device via USB Cable after step 1.

Switch (by default)

1. Press and hold START + Y to power on the joystick. Blue LED will blink four time per cycle.
2. Press and hold PAIRING buton for2 seconds to enter pairing mode. Blue LED will rapidly blink.
3. Go to your Switch Home Page to click on Controllers, then click on Change Grip/Order.
4. Blue LED will be solid blue when connection is successful.
• When connected to your Switch, DOWN + SELECT = Switch HOME button.

Battery

Status LED indicator
Low battery mode Red blinking LED
Battery Charging Green blinking LED
Battery fully charged Green LED turns off
  • Built-in 480 mAh Li-on.
  • 18 Hours of play time.
  • Rechargeable via USB cable with 1-2 hour charging time.
  • Press START for 8 seconds to force turn off your Arcade Stick.

Power Saving

  1. Joystick enters sleep mode in l minute with no Bluetooth connection.
  2. Joystick enters sleep mode in 15 minutes with no use
  3. Use the joystick to wake your N30 Joystick。

Support

Please visit support.8bitdo.com for further information and additional support.

 

8Bitdo NES Classic Edition Retro Receiver User Manual

Retro Receiver for NES Classic Edition

Instruction Manual

Supported Controllers

Supported Controllers

For Nintendo Switch Joy-con

1-insert Retro Receiver into console and then press button
(the LED will rapidly blink)

2-Press your joy-con’s sync button.
3-Wait untill your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on
4-For next connection only need to press A button

Nintendo Switch Joy-con

For Nintendo Switch Pro Controller

1-insert Retro Receiver into console and then press pairing button (the LED will rapidly blink)
2-press your switch pro controller’s sync button
3-Wait untill your Retro Receiver’s LED is solid blue anfd the controller’s #1 LED stay on
4-For next connection only need to press A button

Nintendo Switch Pro Controller

For 8Bitdo controllers

1-Power on 8Bitdo controller (Mode 1) to enter pairing mode.
2-insert Retro Receiver into console and then press the pairing button(the LED will rapidly blink)
3-Wait intill your Retro Receiver and your 8Bitdo controller’s LEDs are both solid blue
4-Your controller is now paired


8Bitdo-Controller

For Wii Rmote/Wii Motionplus controller

1-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink)
2-Press the Wii Remote/Wii MotionPlus controller’s sync button.
3-wait untill your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4-To re-sync after powering your console down.
For Wii Remote : press 1 and 2 buttons.
For Wii MotionPlus : Press A button

Wii RmoteWii Motionplus controller

For Wii U pro controller

1-insert Retro Receiver into console and then press the pairing button(the LED will rapidly blik)
2-Press your Wii U Pro controller’s sync button.
3-Wait untill your Retro Receiver’s is solid blue and the controller’s #1LED stay on
4-For next connection only need to press A button

Wii U pro controller

For PS3 controller

1-Download and Run 8Bitdo Retro Receiver Tools in your PC available for Mac and PC.
2-On your Retro Receiver,hold down the pairing button and connect it to your MAC/PC via USB
3-Connect your PS3 controller to MAC/PC via USB.
4-Once your Retro Receiver and PS3 controller are both connected via USB
click the “Pair” button in the software
5-Once pairing is complete ,you can insert Retro Receiver into your console
6-Now press the PS button on your PS3 controller.
7-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on.
8-To re-sync after powering your console down,begin from step6.

PS3.controller

For PS4 controller

1-insert Retro Receiver into console and then press pairing button(the LED will rapidly blink)
2-Press and hold the PS and share buttons until the lightbar begins to strobe quickly in double.
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s lightbar stay on.
4-For next Connection only need to press PS button and wait until receiver’s LED is solid blue.

PS4 controller

instruction Manual For X-Input

X-Input

For 8Bitdo controllers

1-Power on 8bitdo controller(Mode 1) to enter pairing mode.
2-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
3-Wait until your Retro receiver and your 8bitdo controller’s LEDs are both solid blue.
4-Your controller is now paired.

8Bitdo.controllers(x-input)
structure for 8bitdo controllers.X-input

For Wii Remote/Wii MotionPlus controller

1-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink)
2-Press the Wii Remote/Wii MotionPlus controller’s sync button.
3-Wait until your Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4-To re-sync after powering your console down.
For Wii Remote:Press 1 and 2 buttons.
For Wii MotionPlus :press A button

x-input for RemoteWii MotionPlus controller

For Wii U Pro controller

1-insert Retro Receiver console and then the pairing button (the LED will rapidly blink)
2-press your Wii U pro controller’s sync button
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on
4-For next connection only need to press A button.

Wii U Pro controller.x-input

For PS3 controller

1-Download and Run 8Bitdo Retro Receiver Tools in your PC available for Mac and PC.
2-On your Retro Receiver,hold down the pairing button and connect it to your MAC/PC via USB.
3-Connect your PS3 controller to MAC/PC via USB.
4-Once your Retro Receiver and PS3 controller are both connected via USB
click the “Pair” button in the software.
5-Once pairing is complete ,you can insert Retro Receiver into your console.
6-Now press the PS button on your PS3 controller.
7-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on.
8-To re-sync after powering your console down,begin from step6.

PS3 controller.Xinput

For PS4 controller

1-insert Retro Receiver into console and then press pairing button(the LED will rapidly blink).
2-Press and hold the PS and share buttons until the lightbar begins to strobe quickly in double.
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s lightbar stay on.
4-For next Connection only need to press PS button and wait until receiver’s LED is solid blue.

PS4 controller.X-input

Instruction Manual for PS 3

PS3

For 8Bitdo controllers

1-Power on 8bitdo controller(Mode 1) to enter pairing mode.
2-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
3-Wait until your Retro receiver and your 8bitdo controller’s LEDs are both solid blue.
4-Your controller is now paired.

8Bitdo controllers for ps3
8Bitdo controllers for ps3 (prt2)

For Wii Remote/Wii MotionPlus controller

1-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink)
2-Press the Wii Remote/Wii MotionPlus controller’s sync button.
3-Wait until your Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4-To re-sync after powering your console down.
For Wii Remote:Press 1 and 2 buttons.
For Wii MotionPlus :press A button

Wii RemoteWii MotionPlus controller for PS3

For Wii U Pro controller

1-insert Retro Receiver console and then the pairing button (the LED will rapidly blink)
2-press your Wii U pro controller’s sync button
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on
4-For next connection only need to press A button.

Wii U Pro controller for ps3

 

8Bitdo NES Retro Receiver User Manual

 

Retro Receiver for NES

instruction manual

Supported Controllers

supported.controllers

For Nintendo Switch Joy-con

1-insert Retro Receiver into console and then press button
(the LED will rapidly blink)

2-Press your joy-con’s sync button.
3-Wait untill your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on
4-For next connection only need to press A button

Nintendo Switch Joy-con

For Nintendo Switch Pro Controller

1-insert Retro Receiver into console and then press pairing button (the LED will rapidly blink)
2-press your switch pro controller’s sync button
3-Wait untill your Retro Receiver’s LED is solid blue anfd the controller’s #1 LED stay on
4-For next connection only need to press A button

Nintendo Switch Pro Controller

For 8Bitdo controllers

1-Power on 8Bitdo controller (Mode 1) to enter pairing mode.
2-insert Retro Receiver into console and then press the pairing button(the LED will rapidly blink)
3-Wait intill your Retro Receiver and your 8Bitdo controller’s LEDs are both solid blue
4-Your controller is now paired


8Bitdo-Controller

For Wii Rmote/Wii Motionplus controller

1-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink)
2-Press the Wii Remote/Wii MotionPlus controller’s sync button.
3-wait untill your Retro Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4-To re-sync after powering your console down.
For Wii Remote : press 1 and 2 buttons.
For Wii MotionPlus : Press A button

Wii Rmote/Wii Motionplus controller

For Wii U pro controller

1-insert Retro Receiver into console and then press the pairing button(the LED will rapidly blik)
2-Press your U Pro controller’s sync button.
3-Wait untill your Retro Receiver’s is solid blue and the controller’s #1LED stay on
4-For next connection only need to press A button

Wii U pro controller

For PS3 controller

1-Download and Run 8Bitdo Retro Receiver Tools in your PC available for Mac and PC.
2-On your Retro Receiver,hold down the pairing button and connect it to your MAC/PC via USB
3-Connect your PS3 controller to MAC/PC via USB.
4-Once your Retro Receiver and PS3 controller are both connected via USB
click the “Pair” button in the software
5-Once pairing is complete ,you can insert Retro Receiver into your console
6-Now press the PS button on your PS3 controller.
7-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on.
8-To re-sync after powering your console down,begin from step6.

PS3.controller

For PS4 controller

1-insert Retro Receiver into console and then press pairing button(the LED will rapidly blink)
2-Press and hold the PS and share buttons until the lightbar begins to strobe quickly in double.
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s lightbar stay on.
4-For next Connection only need to press PS button and wait until receiver’s LED is solid blue.

PS4 controller

instruction Manual For X-Input

X-Input

For 8Bitdo controllers

1-Power on 8bitdo controller(Mode 1) to enter pairing mode.
2-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
3-Wait until your Retro receiver and your 8bitdo controller’s LEDs are both solid blue.
4-Your controller is now paired.

8Bitdo.controllers(x-input)
structure for 8bitdo controllers

For Wii Remote/Wii MotionPlus controller

1-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink)
2-Press the Wii Remote/Wii MotionPlus controller’s sync button.
3-Wait until your Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4-To re-sync after powering your console down.
For Wii Remote:Press 1 and 2 buttons.
For Wii MotionPlus :press A button

x-input for RemoteWii MotionPlus controller

For Wii U Pro controller

1-insert Retro Receiver console and then the pairing button (the LED will rapidly blink)
2-press your Wii U pro controller’s sync button
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on
4-For next connection only need to press A button.

Wii U Pro controller.x-input

For PS3 controller

1-Download and Run 8Bitdo Retro Receiver Tools in your PC available for Mac and PC.
2-On your Retro Receiver,hold down the pairing button and connect it to your MAC/PC via USB.
3-Connect your PS3 controller to MAC/PC via USB.
4-Once your Retro Receiver and PS3 controller are both connected via USB
click the “Pair” button in the software.
5-Once pairing is complete ,you can insert Retro Receiver into your console.
6-Now press the PS button on your PS3 controller.
7-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on.
8-To re-sync after powering your console down,begin from step6.

PS3 controller.Xinput

For PS4 controller

1-insert Retro Receiver into console and then press pairing button(the LED will rapidly blink).
2-Press and hold the PS and share buttons until the lightbar begins to strobe quickly in double.
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s lightbar stay on.
4-For next Connection only need to press PS button and wait until receiver’s LED is solid blue.

PS4 controller.X-input

Instruction Manual for PS 3

PS3

For 8Bitdo controllers

1-Power on 8bitdo controller(Mode 1) to enter pairing mode.
2-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink).
3-Wait until your Retro receiver and your 8bitdo controller’s LEDs are both solid blue.
4-Your controller is now paired.

8Bitdo controllers for ps3
8Bitdo controllers for ps3 (prt2)

For Wii Remote/Wii MotionPlus controller

1-insert Retro Receiver into console and then press the pairing button (the LED will rapidly blink)
2-Press the Wii Remote/Wii MotionPlus controller’s sync button.
3-Wait until your Receiver’s LED is solid blue and the controller’s #1 LED stay on.
4-To re-sync after powering your console down.
For Wii Remote:Press 1 and 2 buttons.
For Wii MotionPlus :press A button

Wii RemoteWii MotionPlus controller for PS3

For Wii U Pro controller

1-insert Retro Receiver console and then the pairing button (the LED will rapidly blink)
2-press your Wii U pro controller’s sync button
3-Wait until your Retro Receiver’s LED is solid blue and the controller’s #1LED stay on
4-For next connection only need to press A button.

Wii U Pro controller for ps3

 

8Bitdo Twin Cube Speakers User Manual

TwinCube Speakers Manual

 


Press POWER button on each speaker. LED on each speaker will rapidly blink.

 


(1) Press and hold|| PLAY button on any of the two speakers for 3 seconds
(2) When you hear ‘Party Searching, speakers enter pairing mode.
(3) When you hear Party Connected, speakers are successfully paired.
(4) LE D on the primary/left speaker will slowly blinktwice every cycle. LED on the secondary/right speaker will slowly blink once each cycle.

 


(1) Bluetooth: find [8Bitdo TwinCube] in your device’s Bluetooth setting, click to connect
(2) Audio cable: plug your audio cable in AUX IN port on the primary speaker to connect.
.TwinCube Speakers will auto reconnect to last paired device.

 


(1)  || Play : 1.Play/Pause,  2.AUX IN mode: Silent / Sound back
(2) +/- volume

 


Press and hold POWER button on each speaker to turn off the system, you will hear a beeping sound.

 

Additional Information

 


(1) Press POWER button on any of the two speakers.
(2) Find [8Bitdo TwinCube] in your device’s Bluetooth setting, click to connect
(3) LED will stay solid, there will also be a sound indicating that connection is successful

 


(1) Music playing will be replaced by ring tone when there is an in-coming call
(2) Press || PLAY button to answer/stop phone call
(3) Press and hold ||  PLAY button to resume music playing.

 


Plug in USB cable LED stays solid LED turns off when battery is fully charged. Charging time >= time 2.5 hours.

 


Please visit support.8bitdo.com for further information and additional support.



(1) Power
(2) Volume-
(3) Play/Pause Answer Phone Call)
(4) Volume +
(5) Battery LED
(6) USB Port
(7) Bluetooth LED
(8) AUX IN

@Done by Fazlul Haque

8BITDO F30 Arcade Joystick User Manual

 

 

FC30 Arcade Joystick

 

Instruction Manual

 

Everything old is new again

 

 

 

ios

1. To enter pairing mode, press and hold HOME + A for 3 seconds. The blue LED will rapidly blink.
2. Enter your iOS devices Bluetooth settings. Pair with [8Bitdo Joy].
3. The LED will be solid blue when the connection is successfull.

macOS / Windows / Android

1. To enter pairing mode, press and hold HOME for 3 seconds. The blue LED will rapidly blink.
2. Enter your devices Bluetooth settings. Pair with [8Bitdo Joy].
3. The LED will be solid blue when the connection is successful.

Note: USB OTG might be needed with some Android devices

 

 

1. Press and hold HOME for 3 seconds. The blue LED will rapidly blink.
2. Connect the Micro USB cable to your controller and preferred device please.

Note: your iOS device must be in English

 

 

Status

Low battery mode
Battery charging
Battery fully charged
LED Indicator

Red blinking LED
Green blinkine LED
Green LED turns off

 

 

To upgrade the firmware, please visit: www.Bbitdo.com

 

 

We are continuously developing and providing additional support for new game systems and products
Please visit www.Bbitdo.com for more information on how to update your controller with unique features.

 

 

1. Please visit our official website for up to date information.
2. Please charge the controller for 20 minutes before using it again if it has been put away for a lengthy perlod of time.
3. To avoid any physical damage of the controller, please ensure to keep it in a clean and dry place, away from high temperature, grease or any chemical substance.

 

 

Dimensions : width: 360 mm (14.17 inches)
Height: 231 mm 19.09 inches)
Depth: 59 mm (2.32 inches)
Connectivity : Wireless Bluetooth, Micro-USB
Range : 10 Meters
Compatibility : mac OSX, Windows, ios, Android
Battery Type : Built-in 1000 mAh Li-on, rechargeable
Battery Life : 40 Hours with 1-2 hour charging time
Controller Modes : Bluetooth Keyboard, iCade, Android Joystick, Emu-Touch Screen.
Weight : 2.980 kg with packaging

 

GT08 User Manual

User Guide v1.2

Attention before using:

1. Watchband tightness standards: cross the watchband, can be added into an index finger as the standard;
2. Pairing connection for the first time, without using bluetooth pairing method, only need close NFC on the watchband to mobile phone NFC antenna location nearly.SmartWatch NFC antenna position , please reference the overview products (diagram).
3. Use watchband for the first time, will be tight, hard to buckle into, pls follow as below methods: Put right index finger inside of the watchband , from the top push button in.

Use watchband

1. Safe instructions and main precautions

1.1 The company reserves the right to revised the manual without any prior notice.
1.2 Please charge more than 2 hours before using
1.3 Security Code

To prevent others use your product without authorization, the original password is 1122.In order to ensure the security of your personal information, please modify the original password and remember it.

2. Product Introduction

2.1 Introduction

Components of SmartWatch

Power button: Turn on/off, Wake up, Shut down, Back;

USB:Charging and data function;

Touch screen: capacitive touch screen, the function can be operationed in capacitive touch screen.

2.2 Enter Quickly

After turn on,finger drag left enter the next menu, drag right to return back the menu;Finger drag from the top to
down, enter into the notification bar,from the bottom to top, back to the main menu.
Drag distance need drag over half of the screen,if drag too short, will be mistaken for a click.
The function icon can be place the position freely according to your ideas , click ok to sure.

2.3 Using the Clock screen

While using the Watch, press the Power button to open the Clock screen.Then click the central of screen to change clock type.

Clock screen faces

Setup ways:

method 1:turn on,on the Clock screen,click the central of screen to change clock type.,there are 3 types can be selected.
method 2:turn on,enter the menu :setup–phone setup–Standby menu–Unlock type selection.

2.4 Theme Settings

Setting Method:

Go into the smart watch menu: themes-theme Settings-select your theme

3. Operation Quickly

3.1 Download the synchronous software

Methods 1: turn on the menu of watches – enter into QR Codes directory, using mobile phone QR code scanning software scan the QR code on the watch.
Methods 2: Using mobile phone scan below QR code to download

QR code

Method 3, using mobile browser, enter the following URL to download
http://c3.cli.im/FT5K1A

After download, according to the prompts to install the application. This Program only support synchronization between watch and android smart phone,will not charge mobile phone network traffic.
If you have downloaded relevant software from other channels , please check the software version,
please use the latest version of the synchronization software, to ensure the normal use of function.
If software version has upgraded, please update synchronization software.

3.2 Installation and use synchronization software

Android application software installation:

On smartphone, according to the normal android software installation, when installation complete,
can be stored into the phone memory or synchronization assistant software installation can be used.

Android applications use method: ( installed software already)

(smartphone)Enter the Settings –auxiliary Settings–bluetooth notice (services) click enter,
enable the service.
(when start using, there will be a warning, please select “ok”) software can be automatically run in the background,
synchronizing function can be used .as following:

synchronizing function

Click on the bluetooth notice, choose “notification service”,
in the “notice”,choose to push personal application or system application you need;
Telephone service function, including text messages and telephone;Looking for watch。

Note:when you use the back-end to clean up or close the back-end application software,
please do not close this bluetooth notification service,
if closed, sync will influence the watch with a mobile phone.

3.3 Bluetooth connectivity and synchronization function

3.3.1 from the mobile phone to connect Watch

Enter Mobile phone settings – turn on bluetooth – search equipment, when find GT08,
click choose matching, and select “yes” on the watch, matching success, when there is a phone book request,
please click “ok”,
it is better choose “next time no longer prompt” at the same time,
convenient for next time connection, the phone book will sync directly, not prompt again.
Note:If has installed a synchronization software,
pls also turn on this synchronization software on mobile phone in auxiliary function,
after connection,within 2-5 seconds, the mobile phone terminal will show the bluetooth connected;
on smart watch at the same time,will prompts you automatic synchronization cellphone time,
it indicates that the synchronization function is enabled.When mobile phone have a new message coming,
will synchronization to smart watches in timely.
3.3.2From the smart watch to connect mobile phone
On the smart watch,select the bluetooth dialer – click to search bluetooth device –
find your smartphone (such as samsung 9500) – click connection;the continue process operation as 3.3.1
3.3.2From the smart watch to connect mobile phone On the smart watch,
select the bluetooth dialer – click to search bluetooth device – find your smartphone (such as samsung 9500)
– click connection;the continue process operation as 3.3.1
Note: At the same time,the mobile phone need turn on the bluetooth
and allow to be searched by around bluetooth products

3.4 Function menu description

3.4.1 Message mobile phones synchronous message or smart watch message

3.4.2 Bluetooth

3.4.3 Set up the state of the bluetooth, turn on or off.

3.4.4 Call Records

3.4.5 After connecting the bluetooth, you can view your call status of the near term。

Bluetooth Dialer :

From the watches to connect the mobile phone for matching;

3.4.6 Remote Notification

Synchronous Show the message from mobile phone terminal , such as: QQ, WeChat, messages, time, Twitter, Facebook etc.;

3.4.7 Remote Take Photos

Controlling from the watch,using mobile phone camera take pictures;Need turn on the android mobile phone’s camera advance.

3.4.8 Anti-lost

Watch looking for mobile phone or mobile phone looking for watch. Two-way anti lost;

3.4.9 Setup

Note: In the phone setting, you can set the clock type and theme;In the security Settings, the default security code: 1122

3.4.10 Pedometer

In pedometer Settings, drag to left, you can see steps and burn calories, speed, mileage etc.
movement information;
In the process of movement, if want to go back to the main menu, and don’t want to stop step function,
please press the power button.pedometer function will continue to run in the background.
Motion synchronization data, please see the behind dynamic capabilities.

3.4.11 Sleep Monitoring

According to your sleep time to show the quality of your sleep.

3.4.12 Sedentary Remind

Can set up the time, remind you need to take exercise;It is recommended that one time at least per hour;

3.4.13 QR code

Scan the QR code, can download the synchronization software, if have the new version software to upgrade,
please contact with our company, we will provided the new download address;Please do not use WeChat or QQ
,or others browser scanning and download.

3.4.14 Intelligent search

Searching for the relevant information on the watch

3.4.15 Clock

3.4.16 Calendar

3.4.17 Calculator

3.4.18 Profiles

3.4.19 File Manager

3.4.20 Music Player

Can play music on the watch and mobile phone music connected bluetooth;

3.4.21 Theme, as shown in the theme Settings

3.4.22 Camera

3.4.23 Video recording device

3.4.24 Photo

3.4.25 Video Player

3.4.26 Record

4.Precautions for use

4.1 Please charge fully before use, charging time need 1-2 hours.
4.2 Charge line can use android smartphone charge line and authentic charger;
Or use the standard configuration
accessories;
4.3 Bluetooth disconnect if exceeds the distance, after using two-way anti-lost,if do not reconnect again,
it cannot use the search function;
4.4 Using bluetooth,it will be disconnect occasionally,please reconnect(if over 5 minutes not connected,
need connect manually)When connection,
please pay attention to choose agree with the phone book synchronous;Otherwise,
it will not be able to show the calls from phone book;
4.5 Music function, because of there are different android mobile phone,
some will show the name of the song ,some mobile phone is can not show the name of the song, this is normal.

5. Dynamic movement data synchronization function

5.1 Download Dynamic movement back-end service software

QR code

Method one: scan the QR code, installation Dynamic movement
background services software;Installation method as above;
Method Two: Log in background services website: www.fundo.cc download dynamic movement APK;

5.2 Sport data storage and sharing
5.2.1 Registered ID and login dynamic server, to accurate accounting sport data and give you the correct guidance,pls set your parameters, including height, weight, age.
5.2.2 Connect Smart Watch and mobile phone bluetooth,
and connect the bluetooth synchronization software;Same as above
5.2.3 After do exercise, click the “reset” data on the watch, can store multiple data
5.2.4 In the mobile phone, use dynamic software synchronous data,
synchronization data to back-end to share and store.Back-end will record your movement process and data
5.2.5 Please reference the function and use introduction on the website about the other function
and new features for the dynamic movement software.
5.2.6 Dynamic service website:www.fundo.cc

6. NFC Application

6.1 The smart watch with NFC function(Near Filed Communication);
Bluetooth pairing password has been written into the smart watch when production on factory
6.2 Smart Watch paired with mobile phone bluetooth, turn on mobile phones bluetooth,
smart watch NFC antenna position close nearly to the mobile phone NFC antenna position
(the different phone will be on different position,
can be searched by move slowly in mobile phone’s back around),
the phone will automatically prompt the bluetooth pairing;
Then pairing as usual.After the smart watch pairing with mobile phones,
need to connect again,or disconnected,
only need two NFC antenna close nearly to contact, without any manual processing.
6.3 Write the content into smart watch NFC:
6.3.1 Mobile phone download the write NFC software ,
there are too many kinds of software sold on the market,we recommended TagWriter
it can be download easy,please installed like android software after downloading;
6.3.2 Written software instructions ( TagWriter for example):
1) open the software, as following figure (figure 1) View is to read,
to read data for NFC module .Please see the content what has been written.
Create and write is to write documents

2) Click Create and write go into the next interface:(figure 2)
3) Write in a bluetooth address and password, click New, shown as figure 3,
and then select bluetooth, shown as figure 4,
then searching the connected Bluetooth watch (such as M2)

4) click the device name M2, and then go into the next interface (figure 5),
click Next enter the Next step shown as figure 6, tick the write multiple NFC,
click Next ,in the next step, shown as figure 7.
Using mobile phone antenna position close to smart watch NFC antenna position,
wait for 2 seconds, watches and cell phone issued a “tick”at the same time,success shown as figure 8.

5) write other content, steps and methods are same as above, only in
step 3), choose a different content, it can be message or contacts.

7. Common Troubleshooting Guides

If have any problems when using the smart watch, please refer to the following terms and conditions.
If the problem still exists, please contact the dealer or the designated maintenance personnel.

7.1 Can not turn on
Press the power button too short, please press over 3 seconds.
Battery Power too low, please charge.
7.2 Shut down automatic Battery Power too low, please charge.
7.3 Using time is very short
Not fully battery power, please make sure Charging enough time (minimum 2 hours).
Use the SIM card, but the signal is very poor, lead to cell phone use big current.
7.4 can’t normal charge
Check whether the battery is available, the performance of the battery will reduce after a few years.
Check the charger is working correctly, change the new charger to try Check the connect USB charging line interface
try again.
7.5 Not show the caller’s name
When the bluetooth connection, it not choose to upload directory;or not tick uploaded phone book;
Reconnect again, do not sync the contacts, please reconnect again and pairing.
7.6 Voice quality is not good
Smartwatch and the mobile phone too far away, please come close;
Or Bluetooth signal is bad.
The mobile phone signal is bad, change another place to answer the phone.
7.7 Dynamic data can’t sync, because of not log in the back-end,
movement data can’t save in the back-end,please register and log in.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions
(1) This device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

SAR:

The radiated output power of this device is below the FCC
radio frequency exposure limits. Nevertheless, the device
should be used in such a manner that the potential for human
contact is minimized during normal operation.
The exposure standard for wireless devices employs a unit of
a measurement iknown as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6 W/Kg. Tests for SAR are
conducted using standard operating positions accepted by the
FCC with the device transmitting at its highest certified power
level in all tested frequency bands. Although the SAR is
determined at the highest certified power level, the actual SAR
level of the device while operating can be well below the
maximum value. This is because the device is designed to
operate at multiple power levels so as to use only the power
required to reach the network. In general, the closer you are to
a wireless base station antenna, the lower the power output. To
avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna should be
minimized.

 

Sharper Image DX-3 Video Drone User Manul

Sharper Image DX-3 Drone Manual Rechargeable 2.4GHz Video Drone

Rechargeable 2.4GHz DX-3 VIDEO DRONE

Download the PDF version here.

GETTING TO KNOW YOUR DRONE

PLEASE READ ALL WARNINGS AND INSTRUCTIONS
PRIOR TO USE. KEEP THIS DOCUMENT AS IT CONTAINS
IMPORTANT INFORMATION ABOUT YOUR DRONE.

1. CHARGING

  • Drone must be charged before each use (USB cable included)
  • Indicator light will turn off once fully charged
  • Install batteries in remote

2. PAIRING

Before each flight pair the remote with the drone:

  1. Turn your drone on and place on a flat, level surface
  2. Turn on the remote on and move the left joystick down, then up, then down again
  3. The beep will indicate successful pairing

3. DIRECTIONAL LIGHTS

  • White lights indicate the front of the drone
  • Red lights indicate the back of the drone
  • Not applicable in auto-orientation mode

4. REMOTE CONTROL OVERVIEW

Practice flying your drone below 10 feet and at low speeds until comfortable with all
controls to avoid unnecessary damage or injury

Left joystick
Up/Down controls elevation
Left/Right controls spin
Right joystick
controls flight direction
Direction Trim
use to eliminate drift To cut power to drone, move left joystick to down position

QUESTIONS OR CONCERNS?

PLEASE GIVE US A call ..WE ARE HERE TO HELP

CHOKING HAZARD
SMALL PARTS NOT FOR CHILDREN UNDER 3 YEARS
ADULT ASSEMBLY REQUIRED

CUSTOMER SERVICE

(800)374-2744

Before Calling please locate the 10 digits code printed on the back of your remote

Contents

INTRODUCTION

Congratulations on your purchase of the Sharper Image Rechargeable 2.4 GHz DX-3 Video Drone.Get ready to
soar to new heights. Master the art of drone flying and stunting with remote
control maneuverability. This lightweight stunting drone will provide
hours of fun.

SPECIFICATIONS

Remote Controller Battery:6×1.5V AA
Charging Time: Approximately 120 minutes
Drone Battery: 800 mAh Li-po
Maximum Recommended Altitude 150 ft.

TABLE OF CONTENTS

General Warnings

Contents and Remote Battery Installation

Charging LiPo and Replacing Propeller

Remote Overview

Operating Drone

Modes and Installing B lade Gaurds

Tips and FCC Warning

General Warnings

READ ALL WARNINGS AND PRECAUTIONS BEFORE USE ∶

SAFETY WARNINGS:

• Not recommended for children under 12 years of age. As with all electrical products, precaution
• should be observed during handling and use to reduce the risk of electrical shock.
• Adult supervision is required at all times.
• Before each use, an adult should review the product and battery to determine that no damage or
• hazards exist
DO NOT TOUCH SPINNING PROPELLERS
• Do not allow anything to intentionally make contact in any way with spinning propellers
• Prevent contact with spinning blades by turning off remote prior to handling drone
Use caution and pay attention to your surroundings while operating drone
• Do not fly drone into animals, people, or inanimate objects

• Keep drone away from power lines, buildings, trees, public areas, and any other potentially
• hazardous areas.
• Do not operate in rain, heavy wind, and or any type of severe weather
• Do not land drone on wet surfaces
• Never touch or allow others to touch drone while it is flying
• Always turn drone off when it is not in use
• Always fly drone in large open areas
• Never fly drones above or near people, sudden changes in wind or other conditions could lead to
• unexpected crashes.
• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and
• property rights of others.
• The drone shall never be modified or used for anything except its intended purpose.

 

PLEASE RECYCLE OR
DISPOSE OF ELECTRONICS
PROPERLY RECYCLING
INFORMATION IS AVAILABLE AT
WWW.MERCHSOURCE.

 

 

Invasion of Privacy Warning
Always be mindful of others privacy and do not
record video or take images of others without
their consent. Check and comply with your
federal, state and local laws regarding privacy.

 

Contents and Remote Battery Installation

Components OF LITHIUM-POLYMER BATTERY
“AA” batteries

REMOTE BATTERY INFORMATION

1-Slide open battery compartment
2-Install 6 “AA” batteries as shown in diagram shown above
3-Replace and close battery compartment

LITHIUM-POLYMER BATTERY WARNING
There is a risk of fire and personal injury if Li-Po
battery is punctured, damaged or misused
• Never expose battery to extreme temperatures
• or moisture
• Do not subject battery to strong impacts
• Always keep battery away from flammable
• materials
• Only use manufacturer specified batter(ies),
• charger(s), and/or adapters, if applicable,
• specified by the manufacturer
• Battery is not serviceable
• Let battery cool to room temperature before
• charging
• While charging, never leave battery unattended
• Recycle or dispose of battery according to federal
state and local laws
KEEP THIS INSTRUCTION MANUAL FOR REFERENCE

BATTERY WARNING

• Do not mix old and new batteries
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium)
batteries
• Insert batteries using the correct polarity. Do not short-circuit the supply terminal
• Only use manufacturer specified batter(ies), charger(s), and/or adapters, if
applicable, specified by the manufacturer
• Always use, replace, and recharge (if applicable) batteries under adult supervision.

Charging LiPo and Replacing Propellers

CHARGING BATTERY

Note: The Battery Charger will light up when it
is charging the battery and turn off when the
battery is fully charged. Charge time is
approximately 120 minutes.

Turn off the drone before charging.
Connect the Battery Charger to the Micro USB
port on the Drone.
Connect USB connector to power source.

Method for CHARGING BATTERY

Replacing Propellers

1. Follow diagram.
2. Remove screw from top of Propeller
3. Remove broken Propeller and
replace with new Propeller.
4. Make sure you installed the correct
blade. Each blade has a number
written on it.Match the blades with
the corresponding number on the drone.
5. Insert screw into top of Propeller

Unistall Propeller

broken Propeller
Remote Overview
Remote Overview
Operating Drone

OPERATING DRONE

Step 1 – Pre Flight Checklist

1. Read all warnings and instructions.
2. Install remote batteries, page 2.
3. Make sure that drone and remote are powered off.
4. Assemble Drone, page 3.
5. Charge batteries, page 3.

Step 2 – Choosing a location

• Drone is designed to be flown indoors and outdoors

• Always make sure you have enough space to fly drone

• Always follow warnings, page 1

Step 3 – Starting Drone

1. Making sure your remote is off, slide drone switch
to ON. Drone lights will begin to flicker
2. Choose a flat even surface and follow the
diagram
3. Turn remote on. Bring the Throttle all the way up
then bring it all the way down. Remote will beep
and drone lights will flicker rapidly then turn on
permanently once paired.
4. Drone is ready for flight.

Step 4 – Lift Off

1. Slowly and carefully press the Throttle Joystick
up. Drone will begin to elevate. You can
compensate for some of the drones drifting by
using the Multi Directional Button or by following
step 5. You may need to practice this step
several times before successfully getting drone
into the air.
2. You can let go of the throttle once you get to your
desired elevation. The drone will engage its auto hover function. auto

Practice Step

Step 5 – Drone Begins to Drift

Follow this step if your drone begins to drift while take off or during flight

• Drone drifts backwards: Press the forward Adjustment Button

• Drone drifts forwards: Press the Backwards Adjustment Button

• Drone drifts left: Press the Right Adjustment Button
• Drone drifts right: Press the Left Adjustment Button
• Drone spins clockwise (viewing drone from top): Slide
the spin Adjustment to the left
• Drone spins counter-clockwise (viewing drone from top):
Slide the Spin Adjustment to the right

Step 6 – Operating Drone in Flight

The drones range is approximately 400 feet or 150 feet of altitude

• Read and be aware of all warnings found on page 1.
• Maintain your desired elevation by using the Throttle
• Push the Throttle joystick to right or left to spin the drone.
• Use the Multi Directional Joystick to move forwards,
backwards, and side to side
• Review step 5 if your drone begins to drift
• Drone will begin to blink when drone is paired to remote
and battery is low

Step 7 – Landing Drone

There are two ways to land the drone

1. Press the Auto Land Button. The drone will slowly begin to land. If
the drone begins to drift, you can still control the drone’s
direction using the Multi Directional Button.
2. Slowly and carefully press the Throttle Joystick down until drone
lands. If the drone begins to drift, you can still control the drone’s
direction using the Multi Directional Button


Always turn off remote prior to retrieving
or picking up drone. This will help you
avoid accidently activating propellers.

Modes and Installing Blade Gaurds

MODES

Stunt Button

Once you are comfortable flying the drone, use the Stunt Button to perform acrobatic stunts.

1. Hover the drone to at least above 10 feet.
2. Press the Stunt Button. You will hear beeping coming from the remote
3. Move the Multi Directional Button to the desired direction that you would like the drone to flip

Auto Orientation Button ☮

• Auto Orientation default setting is off. To enter this mode press Auto Orientation “+” button. Re mote
will beep twice.
• After drone success paired, the 2 white LED lights toward orientation will be the original forward
orientation, when drone is in auto orientation mode, whatever the drone spin, the forward orientation
will be previous original forward orientation.
• Remote will beep every 6s to indicate the drone is in Auto Orientation mode.
• To exit mode, press the “+“ button. Remote will sound 1 long beep indicating that it has exited Auto
Orientation mode.

Auto Landing Button ⚇

• Make sure you have achieved level, balanced flight, where the drone is neither climbing nor
descending.This mode allows you to safely and slowly land your drone without having to control the
speed. It is done for you automatically.
• The ideal auto landing height is 25ft.
• Press the “-“ button to trigger auto land. Remote will beep continuously until drone lands
• Do NOT touch the left control stick. This will interrupt the landing sequence.
• To steer the drone during landing, use the right control until drone has reached the ground.
• Press the “-“ button again to exit auto landing mode.

NOTE: Please make sure the throttle joystick is on down position before exit auto landing mode.

Camera – taking pictures and creating videos

• Taking a picture- press Camera Button once to take a picture. 4 main lights will blink once and
audible beep heard indicating photo has been taken.
• Creating video- press Video Button once to take a video. Main lights will blink continuously indicating
video is being recorded. Lights will go solid (stop blinking) when video recording has stopped.
• Please press the video button again to stop the video creating.

NOTE: Please make sure the throttle joystick is on down position before exit auto landing mode.

INSTALLING BLADE GAURDS

• Click blade guards in place per
diagrams below.
• Use provided screws and a small
screwdriver to secure the blade gaurds
before use.

blade guards &screwdriver
Tips and FCC Warning

TIPS

• Do not crash drone into sand or dirt. Drone gears may become clogged
• When first learning to fly, practice lifting off and hovering
• Stay several feet from walls and buildings
• Always Press Throttle all the way down after crashing or when something gets stuck in propellers
• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.
• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of
others.
• The drone shall never be modified or used for anything except its intended purpose.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

TROUBLESHOOTING:

When remote switch is turned on, the remote light does not illuminate:

1) Check that batteries in the remote are installed correctly OR
2) Replace with new batteries

During drone flight, the remote LED is flashing:

1) Remote batteries are low; replace them with new batteries

Drone and remote properly pair, but the drone will not lift-off:

1) Drone Li-Po needs charging. Use charging cable to connect the drone to power source.

After trimming the drone, the drone flight is very unstable and cannot fly properly:

1) One or more blades are most likely damaged;
2) Turn off the drone and remote.
3) Replace with the proper number replacement blade and try flying again.

After impact, the drone is unstable:

1) Put the left remote control lever to the left bottom and put the right remote control lever
to the right bottom at the same time which connected to the drone (diagram to right).
2) If the above does not resolve the issue, reboot the drone and controller and pair again.

Remote Controller and Drone can not be paired:

1) Check Point: Remote Controller must be closed to Drone, not exceed 4 meters.

Note: If there are 2 sets of Drones within 4 meters for Pairing, you must pair one successfully before pairing the second set.


 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause
harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.


Remote Controller

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio commu- nications.
However there is no guarantee that interference will not occur in aparticular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on the user is encouraged to try to
correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna,
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

©Sharper Image. All Rights Reserved.
SHARPER IMAGE ® name and logo are registered trademarks manufactured and marketed by MerchSource,
LLC under license. All other logos and
trademarks are proprietary to their respective owners. The artwork and design of this package are protected by
US copyright law and may not be
reproduced, distributed, displaced, published or used for any purpose without prior written permission.
Altering, removing or reproducing any of the
trademark or copyright notices on this package is not permitted.

©2016 MerchSource, LLC. All rights reserved.
Distributed by MerchSource, LLC, Irvine, CA 92618.
PATENT PENDING
Printed in China