PACOM 8707 Display Reader Installation Guide

PACOM-logo

PACOM 8707 Display Reader

PACOM-8707-Display-Reader-product

Specifications

Type Code 8707R-001
Supply Voltage 10-30VDC
Power Consumption (Typ.) 55mA@24VDC
Power Consumption (Max.) 100mA@24VDC
Reading distance (Typ.) 30mm
Keyboard Type 16 keys, backlit.

Tactile indication on key 5.

Ingress Protection Rating IP54 (with mounting plate)
Dimensions (W x H x D) 74 x 134 x 31 mm
Weight 240 g
Operating Environment -40 to +60°C
Colour Black
Connection 4+6 way screw terminal block

Product Usage Instructions

Installation and Setup

  1. Ensure power supply matches the specified voltage requirement.
  2. Connect the reader to the appropriate interface based on the communication protocol being used (RS485, Wiegand, OSDP).
  3. Follow the wiring diagram for the proper connection of cables.

Configuration

  1. Set up RS-485 addressing and termination as per the provided guidelines.
  2. Configure the supported card formats in the system settings.

Firmware Update and Key Exchange

  1. Enable OSDP Secure Channel for encrypted communication.
  2. Perform firmware updates and key exchanges as needed by following the system-specific procedures.

INDICATIONS

Display OLED B/W 128×64 px
Optical Indication 1 LED, multi-color
Acoustical Indicator Built-in buzzer

Supported Card Formats

  • 13,56Mhz Mifare Classic
  • Mifare Plus, DESFire EV1 + EV2

Signalling

Interface RS485, Wiegand
Communication OSDP 2
Card Formats 26, 32, 34, 56 bits
Tamper Yes

Cable Recommendation
RS485: Data cable shielded twisted pair 2x2x0.5 mm2 (e.g. Belden 3107A) Wiegand: Data cable shielded 8x1x0.25 mm2 (e.g. Belden 9538)PACOM-8707-Display-Reader-fig- (1)

Wiring

PL1 Description
1 RS485 +
2 RS485 –
3 10-30VDC
4 0V
PL2 Description
1 Wiegand D0
2 Wiegand D1
3 Green LED
4 Red LED
5 Buzzer
6 Signal Ground

SETUP

  • Basic reader configuration is done through the setup menu.
  • To enter the setup menu, make sure that 1) the reader is powered up, and 2) the reader tamper switch is active.
  • Press and hold the Service button on the back of the reader for 5 seconds to bring up the “Enter Setup?” prompt. Confirm by pressing the PACOM-8707-Display-Reader-fig- (3) key to enter the setup menu.
  • The contents of the setup menu may vary depending on reader firmware, but for most common installation scenarios with a single reader using OSDP communication, the default settings do not have to be changed.
  • To save the settings, press the PACOM-8707-Display-Reader-fig- (3)key while in the main menu.

RS-485 Addressing and Termination

Up to four readers can be used at the same time on the RS-485 bus. If more than one reader is used, please make sure that each reader on the bus has its unique address (1-4), and that the RS-485 termination is set up correctly. RS-485 termination must be ON (Active) on the last device at each end of the bus. For a single reader connected to a Door Controller, RS-485 termination should be ON for both the Door Controller and the Reader. For other connection scenarios, make sure that the device at each end of the bus has termination ON to ensure communication is working properly.PACOM-8707-Display-Reader-fig- (2)

OSDP SECURE CHANNEL – MIFARE CARD ENCRYPTION KEYS & FIRMWARE

  • If OSDP Secure Channel is enabled, a set of encryption keys are exchanged between the Door Controller and the Pacom 8707 Reader. Once the encryption keys have been exchanged, the Door Controller and the Pacom 8707 Reader are paired, and are thereafter only able to communicate with each other.
  • If a Pacom 8707 Reader is to be moved to a different Door Controller once OSDP Secure Channel is enabled, it needs to be reset to factory default and the Secure Channel Base Key (SCBK) cleared. It can then be paired again with a different Door.
  • Controller (refer to system system-specific procedure on how to perform the pairing operation).
  • Depending on the type of Door Controller and Management System used, the Pacom 8707 Reader is capable of download of MIFARE Card Encryption Keys as well as new firmware.
  • Please contact Pacom Support for more information on which systems support these options.

DS-HW-8002-SE v240604 Specifications subject to change without notice. Copyright © PACOM Systems

FAQs

Q: How do I reset the Pacom 8707 Reader to factory default?
A: To reset to factory default, clear the Secure Channel Base Key (SCBK) and follow the system-specific procedure for pairing with a different Door Controller.

Q: Can the Pacom 8707 Reader be used outdoors?
A: No, the reader is designed for indoor use only to ensure optimal performance and longevity.

Documents / Resources

PDF thumbnail8707 Display Reader
Installation Guide · 8707 Display Reader, 8707, Display Reader, Reader

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Hej Fungerar denna läsare med passerkort DESfire EV3 4K?

    Jonas Järvbäck asks Hej Fungerar denna läsare med passerkort DESfire EV3 4K?
    Manuals+ clarified question
    Question

    Does the PACOM 8707 Display Reader support DESfire EV3 4K access cards?

    Answer

    Based on the PACOM 8707 Display Reader Installation Guide, the officially supported card formats are:

    • 13.56MHz Mifare Classic
    • Mifare Plus
    • DESFire EV1
    • DESFire EV2

    The manual does not explicitly list DESFire EV3 as a supported format. While EV3 cards are often backward compatible with EV2 readers, the documentation only guarantees support up to EV2. For definitive confirmation regarding EV3 4K compatibility, it is recommended to contact PACOM Support directly.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.