Support | Silver Peak
User Guide for aruba models including: EC-XS EdgeConnect Switcher, EC-XS, EdgeConnect Switcher
Quick Start Guide. FIPS. EC-XS. EC-M-P. EC-XL-P. EC-XL-P-NM. Before You Begin. ❑. Check your packing slip to verify that you have all the necessary.
Quick Start Guide ... Tamper-Evident labels and the Installation Guide are supplied ... Based on your model, refer to the separate instructions for rack.
2022-04-04 — Some appliances power up as soon as they're plugged in, oth- ers don't. If the power is off, turn it on. If you don't plug in all.
File Info : application/pdf, 2 Pages, 352.73KB
DocumentDocumentQuick Start Guide EdgeConnect FIPS EC-XS EC-M-P EC-XL-P EC-XL-P-NM Part 1 - Physical Installation IMPORTANT - READ THIS FIRST: You must install and register your Orchestrator with the Silver Peak Cloud Portal BEFORE setting up an EdgeConnect appliance. After Orchestrator is registered with your account name and key, you can proceed with EdgeConnect installation. If you don't know or are unsure what role the Orchestrator plays, please contact your network architect or deployment lead. 1 Apply Tamper-Evident Labels Tamper-Evident labels and the Installation Guide are supplied with the appliance. Before You Begin Check your packing slip to verify that you have all the necessary items. If installing an EC-M-P, first read, Small Form-Factor Pluggable (SFP) Module Installation Guide. If your EdgeConnect model requires it, ensure that you have the associated rack mount instructions. Make sure you have a standard Phillips screwdriver. Supply circuits should be protected by a minimum 15A, maximum 20A circuit breaker. On the network equipment, identify the 10/100/1000 Ethernet ports and/or the 1Gbps/10Gbps fiber ports. 2 Rack Mount the Appliance Based on your model, refer to the separate instructions for rack mount, desk mount, or wall mount. 3 Install the Appliance into the Network a. Identify the relevant ports on the rear of the appliance. b. Connect network cables from the appliance to the identified network equipment ports. c. DO NOT connect the power cables yet. All copper RJ-45 Gigabit Ethernet interfaces in the Silver Peak appliance support MDI/MDI-X and auto-negotiation. The fiber interfaces support: · LC connectors · multi-mode 50 fiber / 62.5 fiber · single-mode 9 fiber (EC-M-P only) 4 Connect Power Cords Depending on the model, your appliance may have a single power supply, or redundant power supplies. a. Connect each power cable to the Silver Peak appliance and to your local power source. b. For redundancy, plug in all power cords, preferably to different power sources. 5 Turn the Power On Some appliances power up as soon as they're plugged in, others don't. If the power is off, turn it on. If you don't plug in all the power cords, an audible alarm sounds until you do. a. Verify that each power supply's LED illuminates green. b. On the front panel, verify that the Power LED illuminates green or blue. 6 Optionally, connect the management ports It is not necessary, however, if you want to create local, physical access to the management ports, you can do so as follows: Silver Peak assigns the MGMT1 ethernet interface a default IP address of 169.254.0.1 and a subnet mask of /16 (the same as 255.255.0.0). Both RJ-45 Gigabit Ethernet interfaces (MGMT0 and MGMT1) support MDI/MDI-X and auto-negotiation. a. Identify the appliance's MGMT0 and MGMT1 interfaces. b. Using an RJ-45 cable, connect the appliance's MGMT0 interface to the network equipment interface. c. Using another RJ-45 cable, connect the appliance's MGMT1 interface to your PC. © 2021 Aruba, a Hewlett Packard Enterprise company All rights reserved. PN 201792 Rev A Aruba 6280 America Center Drive San Jose, CA 95002 1.877.210.7325 (toll-free in USA) +1.408.935.1850 www.silver-peak.com/support You've now completed the physical installation and are ready to register the product with Unity Orchestrator. Quick Start Guide EdgeConnect FIPS EC-XS EC-M-P EC-XL-P EC-XL-P-NM Part 2 - Registration Before You Begin Make sure that Orchestrator is installed and registered. Verify that you've received the email containing your Account Name and Account Key. IMPORTANT - READ THIS FIRST: You must install and register your Orchestrator with the Silver Peak Cloud Portal BEFORE setting up an EdgeConnect appliance. After Orchestrator is registered with your account name and key, you can proceed with EdgeConnect installation. If you don't know or are unsure what role the Orchestrator plays, please contact your network architect or deployment lead. 1 Approve the Discovered Appliance After you power on the EdgeConnect appliance, it automatically registers its serial number with the Silver Peak Cloud Portal. The portal knows how to associate a serial number with a particular account. a. Go to the Orchestrator. b. In the header, click the blinking box named Appliances Discovered. The Discovered Appliances page opens, listing the most recently discovered appliances first. 2 Complete the Appliance Manager Configuration Wizard a. If you've also purchased EdgeConnect Boost or EdgeConnect Plus, and you want to apply it to this appliance, select the relevant check box(es) on the Deployment Profile page. b. At the end, click Apply. It may take up to two minutes to register the appliance. c. Complete the remaining wizard screens. · On the Deployment page's default configuration, the WANside interfaces use DHCP IP addresses, unless you manually enter static IP addresses. c. After verifying that the appliance is yours, click Approve. d. Select the group and click Apply. The Appliance Manager Configuration Wizard opens. © 2021 Aruba, a Hewlett Packard Enterprise company All rights reserved. PN 201792 Rev A Aruba 6280 America Center Drive San Jose, CA 95002 1.877.210.7325 (toll-free in USA) +1.408.935.1850 www.silver-peak.com/support