Categories: ORTUR

ORTUR Laser Master 3 Laser Engraving Machine Instruction Manual

ORTUR Laser Master 3 Laser Engraving Machine

Dear Customer

Thank you for purchasing Ortur products and hope you have a good experience.

If you are having technical issues with our machine, we have a 24 hours team of customer support that would quickly address the problem.
Please visit our ticketing system at: https://ortur.tech/support  or email us at: Support@ortur.tech

Disclaimer and Safety Guidelines

  1. The laser engraver could generate laser light. It is strictly forbidden to place any living body under the laser emission port (this port is marked with a yellow warning sign).
  2. Patients with photosensitive epilepsy are prohibited from using or approaching the laser device.
  3. When using the laser engraving machine, the operator ànd anyone near the machine must Wear laser safety glasses. Do not operate the laser Without glasses protection (laser goggles). Our machines come with a pair of safety goggles, but additional laser safety glasses can be purchased commercially. Requirements for goggles: wavelength protection 400-445nm (+-5nm), outer diameter +5, minimum L-level L5.
  4. When the laser engraver is working, the operator must pay close attention and not place it alone to prevent the engraved material from catching fire. Please set up the laser engraver in a fireproof area and ensure good ventilation. f possible, we recommend that you purchase a fire extinguisher and keep it close to the machine.
  5. Using the laser engraver in a room that can be closed by a door, making sure that neither the laser beam nor stray light can penetrate the window.
  6. When using the laser engraver, put the door sign or the waning light on the door to indicate that the laser engraver is running.
  7. Make sure there is no flammable material near the laser engraver, we recommend put a fireproof mat under the machine
  8. Ensure an adequate environment when operating the laser engraving. Engraving certain materials may generate fumes, which should be exhausted by a dedicated filtered exhaust.
  9. When the machine is running, do not touch the laser beam or touch it with other objects, which may cause serious bodily injury or beam reflection. Do not touch the radiator, you may burn your body and hands when the laser engraver just stops Working.
  10. Do not let children or teenagers use the laser engraver alone (especially children under the age of 14), adult supervision is required at all times.
  11. For commercial use, using and registering with regulatory authorities and professional associations is mandatory.
  12. The operating temperature range of the machine is -15°C~ 30°C.
  13. The flame sensor is provided to keep our equipment as safe as possible and no warranty, written or implied, is made as to the availability or functionality of the flame sensor.

Airframe Parts

  • Front Assembly 1
  • Rear Assembly 1
  • Sideway of Left Y-axis 1
  • Assembly of X-axis 1
  • Sideway of RightY-axis 1

  • Synchronized Belt 2
  • Laser Wire 1
  • Circuit Group 1
  • USB Cable 1
  • M4 8mm Screws4
  • M36mm Screws 2
  • Idler Assembly 2
  • WIFI Aerial 1

  • M4 Set Screws 2
  • 2mm Allen Key 1
  • 3mm Allen Key 1
  • Wrench 1
  • Testing Acrylic 1
  • Testing Woods 4
  • 2.5mm Allen Key 1
  • Laser Goggle 1

  • Brush 1
  • Cable Ties 10
  • Testing Aluminium Flake 1
  • Power Adapter 1
  • Card Reader+ TF Card 1
  • Machine Key 1
  • YRR Motor Wire 1

Laser Module

  • LU2-10A Laser Module 1
  • Laser Shield 1
  • Air Flow Regulator 1
  • Air Pipe 1 (OD:6mm ID:4mm).
  • Pipe Connector 1
  • Thumb Screw 1
  • Air Assist 1

Assemble the Machine

You need the following parts ready

 

  • Pay attention to the installation direction of the X-axis assembly.

 

  • The installation steps of the synchronous belt on the left and right sides are the same.

  • Push the X-axis assembly to the rear limit point

  • The installation steps are the same for the left and right sides.

Connect Wire

Port Description

  1. WIFI Aerial
  2. Power Input
  3. USB Port
  4. Main Power Button (Status Light)
  5. Key Switch
  6. Emergency Stop Button
  7. TF-card
  8. Upgrade Button (for Upgrading Firmware)
  9. Reset Button
  10. Input and Output Ports
  11. Harness Interface
  12. Y-axis Motor Interface
  13. YRR Transfer Switch
  14. YRR Motor Wire Port

Adjustment of rollers and timing belts

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the users authonity to operate the equipment. This equipment has been tested and tound to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Ihese limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiO Communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisIon reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located for operating in conjunction with any other antenna or transmitter.

Address: No. 1 Building, Ruijin Science and Technology Industrial Park, Changping, Dong guan 523558, Guangdong, china.

  • Facebook
  • Youtube
  • Instagram
  • Twitter

Dongguan Ortur Intelligent Technologies Co,Ltd.

Documents / Resources

ORTUR Laser Master 3 Laser Engraving Machine [pdf] Instruction Manual
LASER-MASTER-3, LASERMASTER3, 2A7JTLASER-MASTER-3, 2A7JTLASERMASTER3, Laser Master 3 Laser Engraving Machine, Laser Master 3, Laser Engraving Machine

Recent Posts

Q-TRAN NEXUS-SW Q-CAP Flexible Fixtures Instruction Manual

NEXUS-SW Q-CAP Flexible Fixtures NEXUS-SW Q-CAP Flexible Fixtures - MICRO 5 SERIES Mounting NOTE: 2…

6 mins ago

Q-TRAN WALA-SW Q-CAP Flexible Fixtures Instruction Manual

WALA-SW Q-CAP Flexible Fixtures WALA-SW Q-CAP Flexible Fixtures - MICRO 5 SERIES Mounting WSC-02: WHITE…

6 mins ago

Q-TRAN WALA-DW Q-CAP Flexible Fixtures Instruction Manual

WALA-DW Q-CAP Flexible Fixtures WALA-DW Q-CAP Flexible Fixtures - MICRO 5 SERIES Mounting WSC-02: WHITE…

6 mins ago

BRESSER Jumbo LCD Wall Clock Instruction Manual

Jumbo LCD Wall Clock Jumbo LCD Wanduhr · Wall Clock Art. No. 7001800CM3000 7001800GYE000 7001800QT5000…

12 mins ago

Q-TRAN WSC-02 WALA-RGB Q-CAP Flexible Fixtures Instruction Manual

WSC-02 WALA-RGB Q-CAP Flexible Fixtures WALA-RGB Q-CAP Flexible Fixtures - MICRO 5 SERIES Mounting WSC-02:…

12 mins ago

DiO 84203-v2 Stylish Battery Operated Wireless Doorbell User Manual

84203-v2 Stylish Battery Operated Wireless Doorbell FR 84203-v2 Carillon design sans fil sur batterie ­…

12 mins ago