Orange Pi 3 LTS
Official website data download:
http://www.orangepi.org/downloadresources/
Product description
What’s Orange Pi 3 LTS?
It’ s an open-source single board computer. It can run Android 9, Ubuntu, Debian. It uses the Allwinner H6 SoC, and has 2GB LPDDR3 SDRAM.
Top view 
- 26 Pin headers
- PMU
- Allwinner H6
(ARM® Cortex -A53 Quad-core 1.8GHZ ) 64 bit - WiFi + BT
- Ethernet chip
- IR Receiver
- USB2.0
- Gigabit Ethernet
- WiFi Antenna
- USB3.0+USB2.0
- Audio output and AV
- MIC
- HDMI
- Debug TTL UART
- 8GB EMMC Flash
- Power switch
- LED
- 2GB LPDDR3
- USB Type-C power interface
Bottom view
- TF card slot
Orange Pi 3 LTS v1.2 pinout diagram
Who’s it for?
Orange Pi 3 LTS is for anyone who wants to start creating with technology – not just consuming it. It’s a simple, fun, useful tool that you can use to start taking control of the world around you.
What can I do with Orange Pi 3 LTS?
You can use it to build……
- A computer
- A wireless server
- Games
- Music and sounds
- HD video
- A speaker
- Android
- Scratch
Pretty much anything else, because Orange Pi 3 LTS is open source.
Orange Pi 3 VS Orange Pi 3 LTS
|
Model |
Orange Pi 3 | Orange Pi 3 LTS |
|
Hardware features |
||
| SOC | Allwinner H6 64bit |
Allwinner H6 64bit |
|
CPU Architecture |
Cortex™-A53 | Cortex™-A53 |
| CPU Frequency | 1.8GHz |
1.8GHz |
|
Onboard Storage |
•MicrosD Card •8GB EMMC Flash/EMMC(Default Empty) | •MicrosD Card •8GB EMMC Flash |
| Core Number | 4 |
4 |
|
Memory Bus |
LPDDR3 | LPDDR3 |
| Memory | 1GB/2GB |
2GB |
|
WiFi+BT5.0 |
AP6256 | AW859A |
| Network | 10M/100M/1000M Ethernet |
10M/100M/1000M Ethernet |
|
USB |
1*USB2.0+4*USB3.0 | 2*USB2.0+1*USB3.0 |
| PCB Size | 60×93.5mm |
56x85mm |
|
Power Interface |
DC Input, MicroUSB (OTG) | 5V3A Type-C |
| PMU | Yes |
Yes |
|
PCIE |
Yes | – |
|
Software features |
||
|
OS |
Android7.0,Ubuntu,Debian |
Android9.0,Ubuntu,Debian |
Orange Pi 3, Orange Pi 3 LTS Dimension
Orange Pi 3 Orange Pi 3 LTS
Hardware specification:
|
CPU |
Allwinner H6 Quad-Core 64-Bit 1.8GHz High-Performance Cortex-A53 Processor |
|
GPU |
|
|
RAM |
2GB LPDDR3 (Shared with GPU) |
|
Onboard Storage |
|
|
Onboard Ethernet |
|
|
Onboard WIFI+Bluetooth |
|
|
Video Output |
|
|
Audio Output |
|
|
Power Supply |
5V3A Type-C |
|
Power Management Chip |
AXP805 |
|
USB Port |
1* USB 3.0 HOST, 2* USB 2.0 HOST |
|
Low-Level Peripherals |
|
|
Debug Serial Port |
UART-TX, UART-RX & GND |
|
LED |
Power LED & Status LED |
|
IR Receiver |
Support IR Remote Control |
|
Button |
Power Button (SW4) |
|
Supported OS |
Android 9.0, Ubuntu, Debian |
Appearance specification introduction:
|
Dimension |
56mm x 85mm |
|
weight |
45g |
is a trademark of the Shenzhen Xunlong Software CO., Limited
Completely open source maker artifact
Orange Pi 3 LTS runs Android
Orange Pi 3 LTS runs Ubuntu / Debian
Product display
Front 
Back
45° angle
45° angle
45° angle
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Documents / Resources
 |
orange PI 3 LTS Single Board Computer [pdf] User Manual 3 LTS Single Board Computer, 3 LTS, Single Board Computer, Board Computer, Computer |
