OHSUNG ELECTRONICS LCWB-004 PCB Module 

OHSUNG ELECTRONICS LCWB-004 PCB Module

Contents hide
1 LCWB-004 Overview and Specification
2 FCC Statement
3 ISED Statement
4 Customer Support
5 Documents / Resources
5.1 References
6 Related Posts

LCWB-004 Overview and Specification

Overview

  1. This is a Wi-F i& BLE Combo module
  2. Wi-Fi wireless communication with wired LAN IoT product for protocol and application performance based on IEEE 802.11 b/g/n (HT20) standard technology
  3. The RTL8720 series highly integrated Bluetooth Low Energy controller with a UART interface. It combines a BLE Protocol (PHY, LL, L2CAP, SM, ATT, GAP, GATT), BLE Baseband, Modem, and BLE RF in chip, also supports BLE user GATT-based profile application.
Specification
CategoriesDetails
Model NameLCWB-004
WIFIRange of

Frequency

2400MHz ~ 2483.5MHz
Channel14EA
Transmission Output17 dBm (802.11b)
15 dBm (802.11g)
14 dBm (802.11n)
Reception sensitivity–88 dBm (802.11b)
-75 dBm (802.11g)
-72 dBm (802.11n)
Modulation802.11b : DQPSK, DBPSK, CK 802.11g/n : OFDM/64-QAM,16-QAM, QPSK, BPSK
BLERange of

Frequency

2402 MHz ~ 2480 MHz
Channel40EA
Transmission Output4.5 dBm
Reception sensitivity-95 dBm
AntennaPCB Pattern Antenna
DimensionL x W x H : 48 x 20 x 11.2 (typical) mm
Power5V±0.5V / 12V±1.2V

FCC Statement

FCC Part 15.19 Statements:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Part 15.105 statement(Class B)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15.21

statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Responsible Party InformationSupplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information
Responsible Party –U.S. Contact Information LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs New Jersey, United States, 07632
Modular Approval StatementRegulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual This module has been granted modular approval as below listed FCC rule parts.
  • FCC Rule parts 15C(15.247)
    Summarize the specific operational use conditions
  • The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed below this instruction manual.
    RF exposure considerations
  • The module has been certified for integration into products only by OEM integrators under the following condition:
  • The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
  • The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
  • Mobile use As long as the three conditions above are met, further transmitter testing will not be required.
    OEM integrators should provide the minimum separation distance to end users in their end-product manuals.  Antennas list
This module is certified with the following integrated antenna.
  • Max. Antenna gain: 1.72 dBi / Ant. Type: PCB Printed Antenna  Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.
End Product Labeling

The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:

“Contains FCC ID: BEJ-LCWB004 “Contains IC: 2703H-LCWB004

Information on test modes and additional testing requirements
  • OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.).  Additional testing, Part 15 Subpart B disclaimer
  • The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.
  • The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.

ISED Statement

Licensed-exempt StatementThis device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Statement (MPE)The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
End Product LabelingFinal product labeling (IC)

The module is labeled with its own FCC identification and IC certification number. If the FCC identification and IC certification number are not visible when the module is installed inside another device, the external portion of the device in which the module is installed must also have a label referencing the module included. In this case, the final product must be labeled in a visible area with the following information: Contains transmitter module IC: 2703H-LCWB004

Customer Support

Tel : 1588-6400

[Certification Mark / Certification Number] KC : R-C-LGE-LCWB-004
FCC ID : BEJ-LCWB004
IC : 2703N-LCWB004
CE : Marking (min. 5mm)

Company : Ohsung Electronics
Production Date : 2023.
Manufacturer/Country : Ohsung Electronics/KOREA

Documents / Resources

OHSUNG ELECTRONICS LCWB-004 PCB Module [pdf] Instruction Manual
LCWB-004, LCWB-004 PCB Module, PCB Module, Module

References

Related Posts

Leave a comment

Your email address will not be published. Required fields are marked *